LI-COR Odyssey Bedienungsanleitung
Infrared Imaging System
Installation
Manual
Version 2.1
ODYSSEY
®
Archived Document for Discontinued Imager
ii
Notice
The information contained in this document is
subject to change without notice.
LI-COR MAKES NO WARRANTY OF ANY
KIND WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. LI-COR shall not be liable for errors
contained herein or for incidental or conse-
quential damages in connection with the
furnishing, performance, or use of this
material.
This document contains proprietary infor-
mation which is protected by copyright. All
rights are reserved. No part of this document
may be photocopied, reproduced, or translated
to another language without prior written
consent of LI-COR, Inc.
Printing History
New editions of this manual will incorporate
all material since the previous editions. Update
packages may be used between editions.
Publication Number 984-08467
Revised June 2006
LI-COR is an ISO9001 registered company. © 2001-
2006 LI-COR Inc. LI-COR, Odyssey, and IRDye are
registered trademarks of LI-COR, inc. Netscape is a
registered trademark of Netscape Communications
Corporation. Adobe and Acrobat are registered trade-
marks of Adobe Systems, Incorporated. Windows and
Microsoft are registered trademarks of Microsoft Corpo-
ration.
The Odyssey Infrared Imager and IRDye reagents are
covered by U.S. patents, foreign equivalents, and
patents pending.
Archived Document for Discontinued Imager
iii
Table of Contents
Chapter 1. Installation Quickstart
Unpacking and Initial Inspection ................. 1
Unpacking the Odyssey Imager................ 1
Installation Overview .................................. 2
Firewall Recommendations ......................... 3
Chapter 2: Basic Installation
Procedure
Introduction................................................ 5
Hardware Configuration .............................. 6
Power Connections.................................. 7
Enter the IP Address in Odyssey................... 8
Windows XP Setup .................................... 10
Setting Date and Time............................ 13
Changing Power Management Settings... 13
Log on to Odyssey..................................... 14
Installing Odyssey Application Software .... 17
Importing Key Files for Software
Modules................................................. 19
Adding Users to Odyssey Application
Software................................................. 19
Adding Scanners to Odyssey Application
Software................................................. 20
Configuring Internet Explorer..................... 22
What’s Next .............................................. 23
Chapter 3: Connecting Odyssey to
a Network
Introduction............................................... 25
Configuring Odyssey for Network
Operation .................................................. 26
Network Address Schemes ..................... 28
Using the Networking Setup Page .......... 29
Configuring Windows XP for Network
Operation ..................................................30
Hardware Configuration.............................34
Verifying the Network Configuration..........36
Using Dynamic Addressing (DHCP)...........37
Determining a Dynamically Assigned
IP Address...............................................37
Configuring Scanners in Odyssey
Software.....................................................38
What’s Next...............................................39
Chapter 4: Using Two Networks for
Odyssey and a LAN
Configuring Computers With Two Network
Cards .........................................................41
Connections ...................................................42
Chapter 5: Appendices
Configuring the Netscape Browser .............43
Network Address Form ..............................45
Archived Document for Discontinued Imager
iii
Archived Document for Discontinued Imager
1
Check your packing list to verify that you received everything
included with the Odyssey
®
Infrared Imaging System, including the
following items:
•
Odyssey Infrared Imager.
•
Odyssey Manuals and Accessories Kit, which includes (contents
may vary):
- Odyssey Instruction Manuals and Protocols.
- Odyssey Application Software CD.
- 25
×
25 cm silicone rubber pad and 10 cm roller.
- Microplate Alignment Guide.
- Marking pen and ruler (visible on infrared scans).
- Ethernet switch.
- Power cable and two network cables.
- Calibration/focus page package.
•
Computer, monitor, and accessories.
Unpacking the Odyssey Imager
Remove the
Manuals and Accessories Kit
and set it aside. Use at least
two people to move the Odyssey Imager, as it weighs 32 kg (70
pounds). Lift under the metal enclosure on each side and gently set
the Odyssey Imager at its new position.
Place the instrument on a laboratory bench that is sufficiently sturdy
to bear its weight. Place the instrument away from sinks or other
Unpacking and Initial Inspection
Chapter 1: Installation Quickstart
Archived Document for Discontinued Imager
CHAPTER 1
2
Installation Quickstart
sources of water that pose a shock hazard. Recommended operating
conditions are 15-35 °C and dew point not greater than 20 °C. For
proper ventilation, do not place the instrument in a location where
the fans on the back are blocked.
Each plastic foot on the bottom of the instrument has a threaded
metal insert that can be turned up or down to adjust its height.
Though not needed for proper operation, leveling the instrument
prevents moist membranes from sliding on the scanning surface. If
the laboratory bench is not level, adjust the feet as necessary to level
the instrument. After leveling, make sure all four feet contact the
bench top to prevent the instrument from rocking.
When you are finished unpacking Odyssey, unpack the Ethernet
switch found in the accessories kit.
The Odyssey Infrared Imager is a server device that can be connected
via TCP/IP to the system computer or to your network. The basic
installation procedure in Chapter 2 describes how to connect the
Odyssey Imager directly to the computer, establish communication,
and install Odyssey Application Software. For users who do not want
to connect Odyssey to a network, the installation procedure is
complete after following the instructions in Chapter 2.
Users who want to connect Odyssey to their network should perform
the basic installation in Chapter 2, confirm proper operation, and
then follow the network installation procedure in Chapter 3 to
complete the installation. Connection to a network allows image
data, run parameters, and security protocols to be viewed or changed
using any computer on the network. For example, finished scans can
be downloaded from the Odyssey hard disk to a computer in your
office for analysis and storage.
Installation Overview
Archived Document for Discontinued Imager
3
For networks connected to the Internet, the safest way to protect your
research and data is to put the Odyssey instrument and computer on
a subnet that is behind a firewall. Inexpensive firewall appliances
can perform this function. Contact your local IT department for help
in selection and configuration if your organization does not already
provide you with firewall protection. Legitimate, safe, remote access
can still be achieved when the Odyssey system is protected by a
firewall. Failure to adequately protect the Odyssey instrument or its
computer from attack can have very serious consequences that are
not covered by LI-COR's express or implied warranty.
Firewall Recommendations
Archived Document for Discontinued Imager
iii
Archived Document for Discontinued Imager
5
The installation procedure in this chapter configures both the
Odyssey Imager and its computer. Communication is established by
connecting the Odyssey Imager to the computer without using your
network. Using this direct connection, you can verify that the
instrument is working correctly and install the Odyssey Application
Software. After software installation, the computer can be used to
start scans and analyze images. If you want to extend this basic
configuration so files can be transferred over your network, the
Odyssey Imager and computer can be connected to your network as
described in Chapter 3.
The Ethernet switch and two Cat. 5 RJ-45 network cables included
with the system are required for this installation. The following topics
are included in this chapter:
•
Hardware configuration using supplied switch and cables.
•
Entering the IP address on the Odyssey keypad.
•
Configuring Windows
®
XP and entering an IP address for the
computer.
•
Using the Odyssey browser interface to add user accounts.
•
Installing the Odyssey Application Software, and adding users and
scanners.
•
Configuring your browser to work with the Odyssey Imager.
Introduction
Chapter 2: Basic Installation
Procedure
Archived Document for Discontinued Imager
CHAPTER 2
6
Basic Installation Procedure
1)
Unpack the computer and connect the monitor, keyboard, mouse
and any other accessories as described in the documentation
included with your computer. Connect the power cords using the
included surge protector, but don’t turn the computer on
(Windows
®
XP setup is described later in this chapter).
2)
Connect a supplied Cat. 5 RJ-45 cable to the port labeled
10BASE-T
or
100BASE-TX
on the Odyssey back panel as shown below.
3)
Connect the other end of the Cat. 5 RJ-45 cable to port one on the
switch.
4)
Use the second Cat. 5 RJ-45 cable to connect one of the network
ports on the computer to port two on the switch.
Hardware Configuration
Switch
Odyssey
Host Computer With
Odyssey Software And
Internet Browser
Odyssey
Back Panel
Cat. 5 RJ-45 Cable
To Port 1
Cat. 5 RJ-45 Cable
To Port 2
Cat. 5 RJ-45 Cable
To Network Port
TRANSPORT
MOTORLOCK
OPERATE
10BASE-Tor
100BASE-TX
1 2 3 45Uplink
Power
Ethernet Switch
Back Panel
Do not use Port 5
or the Uplink port.
Archived Document for Discontinued Imager
Andere Handbücher für Odyssey
1
Inhaltsverzeichnis
Andere LI-COR Laborausrüstung Handbücher
LI-COR
LI-COR LI-6400 Bedienungsanleitung
LI-COR
LI-COR LI-6800 Bedienungsanleitung
LI-COR
LI-COR Odyssey CLx Bedienungsanleitung
LI-COR
LI-COR Odyssey CLx Bedienungsanleitung
LI-COR
LI-COR Odyssey M 3340 Bedienungsanleitung
LI-COR
LI-COR LI-6400 Bedienungsanleitung
LI-COR
LI-COR 6400-09 Bedienungsanleitung
LI-COR
LI-COR LI-6800 Bedienungsanleitung
LI-COR
LI-COR Odyssey XF Bedienungsanleitung
LI-COR
LI-COR LI-6400XT Bedienungsanleitung
Beliebte Laborausrüstung Handbücher anderer Marken
Agilent Technologies
Agilent Technologies 5800 ICP-OES Bedienungsanleitung
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Bedienungsanleitung
NI
NI PXI-5422 Handbuch
Collomix
Collomix Aqix Bedienungsanleitung
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung
Ocean Insight
Ocean Insight FLAME-NIR+ Bedienungsanleitung
Parker
Parker ALIGN-MG-NA Bedienungsanleitung
BD
BD 644787 Bedienungsanleitung
DENTAURUM
DENTAURUM Compact Megaplus Bedienungsanleitung
Biuged Laboratory Instruments
Biuged Laboratory Instruments BGD 626 Bedienungsanleitung
VWR
VWR SAS Super IAQ Bedienungsanleitung
illumina
illumina MiSeqDx Bedienungsanleitung