Lincoln G Series Bedienungsanleitung

DESCRIPTION

Model 1810

MANUAL CENTRO-LUBER,

GREASE PUMP

Series "G"

The 1810 Centro-Luber is a manually operated multiple stroke grease pump for use on machines where periodic manual

lubrication is acceptable. It is used as the pumping unit for a centrali ed lubrication system having a single line circuit of

Series SL-1, SL-32, or SL-33 Injectors. Injectors can be used in combination where bearing si es or lubricant requirements

indicate such a combination advantageous and most efficient.

Pump dispenses grease up through NLGI #1 and discharges an established amount (*.160 cu. in.) into the circuit for each

full stroke of the pump handle. A built-in cycle indicator in the pump shows completion of the lubrication cycle.

*Based on lubricants that are free of entrapped air. Lubricants that are specifically aerated will reduce output of pump.

Model 1810 has a spring loaded follower in the reservoir and is filled with a filler pump through a filler fitting.

SPECIFICATIONS

LUBRICANT

OUPUT RESERVOIR

CAPACITY LUBRICANT

OUTLET

LUBRICANT OPERATING PRESSURE (PSI)

INJECTOR

SYSTEM MINIUM MAXIMUM RECOMMENDED

* .160 cu in.

per stroke 5 lb.

(150 cu. in.) 1/4" NPTF

Female

SL-1 1,850 3,500 2,500**

SL-32

SL-33 1,200 3,500 2,500**

SUPPLY LINE SPECIFICATIONS

1810

CENTRO-LUBER CENTRALLY

LOCATED ON MACHINE

FOR CONVENIENCE

OF FILLING AND

OPERATION

Section

Page

- C8

- 62K

APR - 96

TO FILL MODEL 1810 WITH FILLER PUMP

1) Use a manual filler pump to fill reservoir through the filler fitting in the

pump body. Attach coupler on delivery hose to filler fitting. Stroke filler

pump handle until lubricant weepage is noted at air vent hole in the

reservoir (lower portion of follower must rise beyond air vent hole to expel

entrapped air from lubricant).

NOTE: When filling the reservoir, caution should be used, as extreme

pressure can cause damage to reservoir and follower assembly.

) A strainer is behind the filler fitting to prevent foreign material from

entering the reservoir. Remove filler fitting to inspect and clean strainer

periodically.

**Pressure i dicator of pump set at factory.

One Lincoln Way

St. Louis, Missouri 63120-1578

(314 679-4200

Printed in U.S.A.

SEAMLESS STEEL

TUBE SIZE

MAXIMUM LENGTH OF

SUPPLY LINE GREASE

NLGI #0 NLGI #1

3/8" O.D. x .028" Wall 50 Ft. 25 Ft.

AIR VENT

HOLE

RESERVOIR

FILLER

FITTING

COUPLER

FILLER PUMP

DELIVERY

HOSE

A+B+C+D+E+F must not exceed maximum supply line

length shown above.

FORM 402621

Form 402621 Page 2

Assembly Note:

Loosely install 16650 and 31128

onto 91613. Then install 91613 into

40434 and tighten to 75 ft-lbs.

Tighten 16650 to 60 ft-lbs.

TO PRIME SYSTEM

S PPLY LINES

After pump reservoir has been filled with recommended lubricant, turn vent plug counterclockwise one complete turn

and operate pump until lubricant flows freely from opening in vent plug to expel air pockets trapped between the pump

and the supply line connection. Tighten vent plug. Remove all plugs in dead ends of the injector manifolds and supply

lines. Operate pump until lubricant flows from any plug opening. Close opening with plug. Continue operating pump

until lubricant flows from another plug opening. Repeat this procedure until all supply lines are primed and plug openings

closed.

FEEDER LINES

Fill each feed line with lubricant before connecting lines to outlet of injectors and bearings. This will prevent having

to cycle each injector for every inch of feed line between injector and bearing.

INJECTORS

Check each individual injector for proper operation. Injector stem moves when injector discharges lubricant to bearing.

This may require cycling system several times. After checking injectors for operation adjust injectors for the volume

required for each individual bearing.

Form 402621 Page 3

SECTION A - A

PART QTY. DESCRIPTION

10127 1Vent plug

12511 1Pipe plug

12635 1 Pin

12637 1Indicator extension

12638 1Packing retainer

12639 1Spring housing

12640 1 Indicator pin

13068 1Toggle

13069 1Eccentric cam

13310 1 Pin

13348 3Tie rod

14359 1Bushing

16395 1Handle

16650* 1Check stop

31104* 1Gasket

31128* 1Gasket

34122* 1Packing (Nitrile)

34230* 1O-ring (Nitrile)

34231* 1Packing (Nitrile)

34274* 1Gasket (Neoprene)

35117* 1Packing (Nitrile)

40408 1Handle casting

40434 1Pump body casting

40435 1 Cover

45939 2Follower guide

50044 2Screw

50531 1Set screw

51003 1Jam nut

51015 1Jam nut

51022 3 Nut

55305* 2Spring

57055 1Spring

57057 1Snap ring

66765 4Retaining ring

66924 2Retaining ring

69217 1 Cotter pin

70397 1Knob

70485* 1Ball

91142 1Indicator assembly

91613 1Bushing &plunger assembly

242260* 1O-ring (Nitrile)

247210 1Reservoir assembly (Acrylic)

SERVICE PARTS

* Recommended service

parts inventory

Form 402621 Page 4

RESERVOIR

HANDLE

INDICATOR

SUPPLY LINE

TO INJECTORS

1st OPERATION

2nd OPERATION

OPERATION

The Centro-Luber System lubrication cycle consists of two

operations:

1st OPERATION

The outward stroke of the handle forces lubricant into

the supply line. As handle is operated, lubricant pressure

is built up until it reaches ,500 PSI. When this pressure

is reached, the indicator will move out to its extended

position exposing a red ring on the indicator stem. This

indicates that the necessary pressure needed to operate

the system has been reached and operation of pump

handle is no longer required.

Lubricant pressure built up in the supply line operates the

injectors which dispense a measured amount of lubricant

into the bearing.

2nd OPERATION

Release handle and return it to its normal position

against the reservoir. When handle is in this position

lubricant pressure in the system vents back into the

reservoir. handle must be released for pump to vent.

Operators hand, gripping the handle, prevents the pump

from venting between strokes. Injectors re-charge for

next lubrication cycle.

PUMPING

RANGE

VENTING

POSITION

HANDLE

50531

SET SCREW

13069

ECCENTRIC

CAM

51003

NUT

CENTRO-LUBER IS ALWAYS VENTED EXCEPT DURING PUMPING PERIOD

To adjust Vent Position of Handle loosen the 50531 Set Screw. Then unthread the 51003 Nut

approximately one full turn. The 13069 Eccentric Cam can then be moved to the desired vent

postion. Re-tighten nut and set screw.

NOTE: t may be necessary to try several positions of eccentric cam before desired venting

adjustment is obtained.

RETAIN THIS INFORMATION FOR FUTURE REFERENCE

When ordering replacement parts list: Part Number Description Model Number and Series Letter.

LINCOLN provides a Distributor Network that stocks equipment and replacement parts.

VENT PLUG

SUPPLY LINE

TO INJECTORS

RESERVOIR

HANDLE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lincoln Wasserpumpe Handbücher

Lincoln

Lincoln Quicklub Bedienungsanleitung

Lincoln

Lincoln FlowMaster 85588 Bedienungsanleitung

Lincoln

Lincoln 82050 Betriebsanleitung

Lincoln

Lincoln SKF FlowMaster II A Series Bedienungsanleitung

Lincoln

Lincoln FlowMaster C Series Bedienungsanleitung

Lincoln

Lincoln SKF FlowMaster II A Series Bedienungsanleitung

Lincoln

Lincoln A Series Produkthandbuch

Lincoln

Lincoln SKF ContiMaster Bedienungsanleitung

Lincoln

Lincoln 230 Bedienungsanleitung

Lincoln

Lincoln 1335 Bedienungsanleitung

Lincoln

Lincoln SAF1-YL Bedienungsanleitung

Lincoln

Lincoln QUICKLUB 203 Bedienungsanleitung

Lincoln

Lincoln SKF FlowMaster II 85875 Bedienungsanleitung

Lincoln

Lincoln SAF1-YL Handbuch

Lincoln

Lincoln A Series Bedienungsanleitung

Lincoln

Lincoln SKF GTP-C Bedienungsanleitung

Lincoln

Lincoln 84933 Produkthandbuch

Lincoln

Lincoln 9917 Produkthandbuch

Lincoln

Lincoln FlowMaster A Series Bedienungsanleitung

Lincoln

Lincoln FlowMaster C Series Bedienungsanleitung

Lincoln

Lincoln CENTRO-MATIC FlowMaster 85219 Bedienungsanleitung

Lincoln

Lincoln QUICKLUB 203 Bedienungsanleitung

Lincoln

Lincoln SKF VarioSuper UFV 20 Series Bedienungsanleitung

Lincoln

Lincoln SKF FlowMaster II A Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung