Linksys WBP54G Original Betriebsanleitung

Model No.

Quick Installation

A Division of Cisco Systems, Inc.

Model No.

Wireless

Bridge for Phone Adapters

Wireless-G

Package Contents

• Wireless-G Bridge for Phone Adapters (with

Attached Combo-power/Ethernet Cable)

• CD-ROM with Setup Wizard and User Guide

• Quick Installation Guide

• Registration Card

NOTE:The power adapter for your

Linksys phone adapter or IP phone

will be used to power the Bridge.

NOTE:If you connect the Bridge to a

router, make sure the Bridge and PC

running the Setup Wizard are

connected to the Ethernet network

(LAN) ports of the same router.

The Setup Wizard will guide you

through the steps to configure

and connect the Bridge.

AInsert the Setup CD-ROM

into your CD-ROM drive. The

Setup Wizard should run

automatically, and the

Welcome screen should

appear. If it does not, click

Start and choose Run. In

the field that appears, enter

D:\setup.exe (if “D” is the

letter of your CD-ROM

drive).

BClick Click Here to Start on

the Welcome screen.

CAfter reading the License

Agreement, click Next if you

agree, or click Cancel to

end the installation.

DThis screen will inform you

about which Linksys phone

adapters and IP phones

work with the Bridge. Make

sure your phone adapter or

IP phone is listed on-screen.

Click Next.

EYou will use the PC running

this Setup Wizard to set up

the Bridge. Disconnect the

power jack from the back of

the Linksys phone adapter

or IP phone. (You will use this

power adapter to power the

Bridge.) If your network

router or this PC is in a

different room, disconnect

the power adapter from the

electrical outlet. Move the

power adapter and Bridge

to the room where your

router or PC is located.

Click Next.

FConnect the power jack to

the Power port of the Bridge.

Then plug the power

adapter into an electrical

outlet.

Click Next.

GYou will use the

combination Ethernet

network and power cable

attached to the Bridge.

Connect the Ethernet

network cable of the Bridge

to an Ethernet network (LAN)

port of the router or PC. (Do

not use the power cable

now; you will use it later.)

Make sure the Bridge’s

Ethernet LED is solidly lit or

flashing. Click Next.

HA list of all Bridges for Phone

Adapters that can be

detected by the Setup

Wizard will be displayed.

Select the Bridge you are

installing and click Next. If

the Bridge you want is not

displayed, click the Refresh

List button to search again.

IThis screen will display a list

of wireless networks that can

be detected. Select the

wireless network you want.

If the network you want is

not displayed, click the

Refresh List button to

search again.

To manually enter the SSID

of the network you want,

click the SSID radio button

and enter the SSID of your

wireless network.

Click Next.

JConfigure the wireless

security settings. Select the

method your network is

using, WPA, WPA2,

WEP (128-Bit), or WEP (64-

Bit). Then proceed to the

appropriate instructions. If

you are not using wireless

security, select Disabled,

and proceed to step K.

Set up and Connect the Bridge

2.4

802.11g

WBP54G

IMPORTANT:Some wireless

access points or routers do not

broadcast their status information. If

you do not see the network you

want, click the SSID radio button

and manually enter its SSID.

enter a Passphrase, enter

the WEP key and select the

appropriate number from

the Key Index drop-down

menu. Click Next.

Key 1-4 - The WEP key(s) you

enter must match the WEP

key(s) of your wireless

network. For 64-bit

encryption, enter 10

hexadecimal characters.

For 128-bit encryption, enter

26 hexadecimal

characters. Valid

hexadecimal characters

are “0” to “9” and “A” to “F”.

Key Index - If your access

point or wireless router uses

a different transmit key

number, select that number

from the index.

KReview the new settings.

Click Next to save them.

LThe Bridge will attempt to

connect to the wireless

network using the new

settings.

Make sure the Bridge’s

Wireless LED is solidly lit or

flashing. This indicates that

the Bridge has connected

to the wireless network. If the

attempt succeeds,

proceed to step M.

If the attempt fails, you

have two options offered by

a pop-up screen. Click Yes

to save the new settings

and proceed, or click No to

reconfigure the settings.

MDisconnect the Ethernet

network cable of the Bridge

from the router or PC.

Click Next.

NIf the phone adapter or IP

phone is in a different room,

disconnect the power

adapter from the electrical

outlet. Move the power

adapter and Bridge to the

location of the phone

adapter or IP phone.

Click Next.

ODisconnect the Ethernet

network cable from the

phone adapter or IP phone.

You will use the

combination Ethernet

network and power cable

attached to the Bridge.

Connect the Ethernet

network cable of the Bridge

to the phone adapter or IP

phone.

Click Next.

WPA

TKIP is automatically

selected as the encryption

method. Enter a

Passphrase, also called a

pre-shared key, of 8-63

characters. Click Next.

WPA2

AES is automatically

selected as the encryption

method. Enter a

Passphrase, also called a

pre-shared key, of 8-63

characters. Click Next.

WEP (128-Bit) or WEP (64-Bit)

To automatically generate

a WEP key, enter a

passphrase. To manually

enter a WEP key, leave the

Passphrase field blank.

Then click Next.

NOTE:The passphrase is case-

sensitive and should not

be longer than 16

alphanumeric characters.

It must match the

passphrase of your

wireless network.

A new screen will appear. If

you entered a Passphrase,

the WEP key will be

displayed. If you did not Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and

PConnect the power cable

of the Bridge to the Power

port of the phone adapter

or IP phone. Then connect

the power adapter to an

electrical outlet.

Make sure the Bridge’s

Ethernet and Wireless LEDs

are solidly lit or flashing.

Click Next.

QMake sure your cable

connections match the

cable connections shown

on-screen. Click Next.

ROn the Congratulations

screen, click Exit to exit the

Setup Wizard, or click

Online Registration to

www.linksys.com/registration

Congratulations! The installation

of the Wireless-G Bridge for

Phone Adapters is complete.

WPA

WPA2

WEP

WEP Keys

For additional information or troubleshooting help, refer to the User Guide on the Setup CD-ROM. You can also

call or e-mail for further support.

24-hour Technical Support 800-326-7114 (toll-free from US or Canada)

E-mail Support [email protected]

Website http://www.linksys.com or

http://support.linksys.com

RMA (Return Merchandise Authorization) http://www.linksys.com/support

FTP Site ftp://ftp.linksys.com

Sales Information 800-546-5797 (800-LINKSYS)

WBP54G_V2-QI-51019NC JL

Andere Handbücher für WBP54G

Andere Linksys Netzwerk-Hardware Handbücher

Linksys

Linksys OGV200 - Network Optimizer For Gaming Original Betriebsanleitung

Linksys

Linksys BEFN2PE Bedienungsanleitung

Linksys

Linksys EFR240 Bedienungsanleitung

Linksys

Linksys HPES03 Bedienungsanleitung

Linksys

Linksys VELOP AX5300 Bedienungsanleitung

Linksys

Linksys WET54G V3 Original Betriebsanleitung

Linksys

Linksys WMB54G - Wireless-G Music Bridge Network Audio... Bedienungsanleitung

Linksys

Linksys OGV200 - Network Optimizer For Gaming Bedienungsanleitung

Linksys

Linksys MX5300 Bedienungsanleitung

Linksys

Linksys EFG120 - EtherFast Network Attached Storage NAS... Bedienungsanleitung

Linksys

Linksys EFG120 - EtherFast Network Attached Storage NAS... Bedienungsanleitung

Linksys

Linksys VGA2100 - One Analog Voice Gateway 3 Line Bedienungsanleitung

Linksys

Linksys LKG0F755E Bedienungsanleitung

Linksys

Linksys SVR3000 - One Services Router Bedienungsanleitung

Linksys

Linksys EFG120 - EtherFast Network Attached Storage NAS... Original Betriebsanleitung

Linksys

Linksys EF31SC Bedienungsanleitung

Linksys

Linksys BEFN2PE Original Betriebsanleitung

Linksys

Linksys WMB54G - Wireless-G Music Bridge Network Audio... Bedienungsanleitung

Linksys

Linksys WMB54G - Wireless-G Music Bridge Network Audio... Bedienungsanleitung

Linksys

Linksys EFG80 - EtherFast Instant GigaDrive NAS... Original Betriebsanleitung

Linksys

Linksys EFPC2SC Bedienungsanleitung

Linksys

Linksys EFG80 - EtherFast Instant GigaDrive NAS... Bedienungsanleitung

Linksys

Linksys MX4300 Bedienungsanleitung

Linksys

Linksys HPES03 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung