Linn KUDOS SNEAKY Bedienungsanleitung
PAGE 1
PACK 222 KUDOS5.DOC
Mar 97
INSTALLATION INSTRUCTIONS
LINN KUDOS SNEAKY UPGRADE IN LINN MAJIK / WAKONDA
1. Unpack and check the contents of your KUDOS Sneaky upgrade kit.
Contents list :- 1x KUDOS tuner PCB Tools required : No.1 Pozi screwdriver
1x KUDOS control PCB Small pliers
1x Control area mounting plate 5 mm Nut-runner
2x Nylon Stand offs Multi-Meter
1x Display window
1x 11-buttons assembly
1x Extension connector
2x Ribbon cables
1x Display legends label
4x Push-on rivet washers
3x Spare M3 screws (black)
2x Shake-proof washers
4x Spare ‘Taptite’ screws (black)
2x Nylon insulating bushes.
4x Shorting links -
1 x Used to disable sleep option (point 21)
3 x Used to configure the KUDOS for use in USA, see page 4)
2. On a clean bench, and with a protective pad to protect the facia, turn the MAJIK / WAKONDA upside down,
remove the four screws and slide
off the outer sleeve.
3. With the MAJIK / WAKONDA sitting
on its feet again, remove the two
screws on the back-panel, and take
off the Sneaky slot blanking plate.
4. Push-fit the two white plastic stand-
offs into the holes in the MAJIK /
WAKONDA main PCB until they
audibly ‘click’ and lock into position.
(See photo 1)
5. Push the extension connector into the holes on the underside of the KUDOS
tuner PCB. (See photo 2) It is important to fit this connector first to the KUDOS
tuner PCB, and not to the MAJIK / WAKONDA main PCB, otherwise the pins may
be damaged on assembly.
Time required :
45 minutes
Use anti-static precautions
including work station. If this is
not possible - Ground yourself!
See Service Manual 5.8 for details
STAND-OFFS
Photo 1
Photo 2
EXTENSION
SOCKET
EXTENSION
CONNECTOR
PAGE 2
PACK 222 KUDOS5.DOC
Mar 97
6. Fit the KUDOS tuner PCB into the MAJIK/WAKONDA :-
(i) Align the mounting plate in the
Sneaky slot aperture,
(ii) Align the two white plastic stand-
offs in their holes,
(iii) Apply a steady even pressure on
top of the extension connector and
near the plastic stand-offs to push
the KUDOS tuner PCB into position.
(See photo 3). Try and keep the
board horizontal whilst pushing into
position. Excessive force is not
required.
7. Fit two M3 screws with shake-proof
washers to hold the mounting plate into
the Sneaky slot. The shake-proof
washers MUST be used to ensure
electrical grounding. Check with Multi-
meter (set to Ohms) for continuity
between earth pin of mains plug and top
of screening can on Kudos board.
8. Remove the facia assembly from the MAJIK / WAKONDA :-
(i) Unplug the display ribbon cable and the power-on LED connector,
(ii) Remove the two faciascrews underneath and the two countersunk screws at each end,
then lift off the facia.
9. Now working on the facia assembly, remove the four screws and take off the MAJIK / WAKONDA control
PCB.
10. Lift off the grey rubber switch membrane.
11. Snap off the four legs along on the back of the display window along with the rivet washers.
(See photo 4)
12.Push off the MAJIK / WAKONDA display window
along with the control buttons.
13. Remove the four screws and lift-off the MAJIK /
WAKONDA control area mounting plate.
14. Fit the new KUDOS control area mounting plate,
which has extra holes for the additional buttons,
using the existing screws. Ensure the two in-fill
mouldings which are located under the mounting
plate are correctly positioned. (New screws are
included for use if required.)
15. Fit the new 11-buttons assembly by engaging the
return hooks first to ensure they are not damaged,
and then fit the new window to hold the buttons to the control area plate and push firmly into place.
Ensure the protective film can be easily removed, and is not trapped behind the window.
16. Turn the facia over, fit the display legends label over the locating pins and rivet in place by pushing the
push-on rivet washers HARD into place on the pins using a 5 mm Nut-runner. (See photo 5)
Photo 3
Photo 4
PAGE 3
PACK 222 KUDOS5.DOC
Mar 97
17. Fit one of the long ribbon cables to the
KUDOS control PCB. Both the cables are
same, but the end are handed differently. Fit
the cable with the end that enables the cable
to point directly downwards. (If you connect
this the wrong way around the cable will be too
short.)
18. Fit the KUDOS control board to the facia with
three M3 screws removed previously. A nylon
insulating bush MUST be fitted under the top
screw to prevent a short-circuit to the adjacent
track. (New screws are included for use if
required, as is an additional insulating bush.)
19. Ensure all the buttons are functioning properly
and clicking audibly, then refit the facia
assembly to the MAJIK/WAKONDA using the two countersunk screws at the ends and the two screws
underneath which were removed earlier.
20. Re-fit the power-on LED connector to the
MAJIK / WAKONDA main PCB. Plug the ribbon
cable from the KUDOS control PCB into the
furthest connector (P6) on the KUDOS main
PCB. Plug the second long ribbon cable into
the other connector (P5) on the KUDOS main
PCB using the end which makes the cable
face forwards, and then plug the other end into
the connector (P8) on the MAJIK/WAKONDA
main PCB. (See photo 6) If the cables are
correctly fitted they will cross-over each other.
Incorrect connection will not cause any
damage, but the control panel will not operate.
21.Disable the sleep function of the
MAJIK/WAKONDA display by fitting a link
(CONN 421) to pins 3 on P11 connector. This
passes the “sleep” control over to the Kudos
board and MUST be fitted.
(See photo 7) Previous board revisions will be different, find the pins markedDISPLAY ON .
22.Re-fit the outer sleeve to the MAJIK/WAKONDA using the four screws
underneath which were removed previously.
23. Power the product up and check that all is working and fully
functioning. Remove the protective tape from the front window.
Installation is complete.
Please note:
The Kudos Sneaky is selected by using the following:
top row of buttons on the Majik front panel
ZONE on the large Linn hand set
WHERE on the KUDOS hand set (when available)
&TUNE%on the Majik hand set (steps up and down
through presets only)
The Tuner input on the Majik is not affected and can be used as an
auxiliary input, by selecting tuner. For further details refer to the
Owners Manual.
Happy listening!
Photo 5
Photo 6
Photo 7
P11 - PINS 3
TOP SCREW
P8
P6
P5
PAGE 4
PACK 222 KUDOS5.DOC
Mar 97
24.You should have the following parts left over from the MAJIK / WAKONDA which should be retained in
case of future removal of theKUDOS :-
MAJIK / WAKONDA control board
Sneaky slot blanking plate Control area mounting plate
Rubber switch membrane Six buttons
Display legends label
The Display window should be discarded as the mounting legs have been broken off.
To Configure for USA
If the Kudos is to be used in the USA it must be configured for the USA.
Add shorting links (supplied) to the two-pin connectors at locations LK1 LK2 and LK4 as shown
below.
LK4
(MIDDLE ONE)
LK1
LK2
Photo 8
Inhaltsverzeichnis
Andere Linn Zubehör Handbücher
