LINSHANG LS201 Bedienungsanleitung

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 1 of 8

LS201

Digital Glass Thickness Meter

User Manual V2.0

Please read this manual carefully before using and reserve it for reference.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 2 of 8

I. Product introduction

This instrument use optical reflection principle to measure the glass thickness.Just putting the meter on

the surface of the glass, it can test thickness of triple glazing, double glazing, laminated glass and other

kinds of glass.

II. Parameter

1. Dimension: 130mm * 72mm * 33mm (L * W * H)

2. Measuring range: 70mm of glass thickness, 45mm of air space

3. Measuring accuracy: ±0.1mm

4. Weight: 330g

5. Power Supply: 4 AA alkaline dry batteries

6. Display: LCD 240*160 Pixels

7. Minimum measurement size: 5mm*50mm

III. Button Operations

1. Powering on/off

In the shutdown state, short press “Power/ ” to power on.

If Power on, long press ”Power/ ” to power off.

If power on, the instrument will automatically power off if there is no operation within 10 minutes.

2. Language settings

In the shutdown state, long press ”Power/ ” to enter into the language setting mode.

3. Measuring mode settings

In the measuring results interface, short press “Select/▼” to enter into the measurement setting mode.

Select the measuring modes between “Auto” or “Manual”.

4. Select/▼

In the measuring setting interface, short press “Select/▼” to roll down selection or reduce 1 from the

number.

In the measuring result interface, if the measuring mode is “Auto”, there may be several kinds of

measuring results, short press “Select/▼” to view different results.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 3 of 8

5. Measure/▲

In the measuring result interface, short press “Measure/▲” to get a new measurement.

In the measuring setting interface, short press “Measure/▲” to roll up selection or increase 1 from the

number.

IV. Instrument Setting

The meter need to set the “Language mode” and the “Measurement mode”.

1. Language mode setting

In the shutdown state, long press “Power/ ” to enter into the language setting mode, as shown in the

following figure, short press “Select/▼” or “Measure/▲” to shift between “Chinese” or “English”, short

press “Power/ ” to save and exit.

2. Measurement mode

The measurement mode has two selection “Auto” and ”Manual”.

In the measuring result interface, long press “Select/▼” to enter into the measurement mode setting

interface, short press “Measure/▲” or “Select/▼” to shift between “Auto” and ”Manual”, short press

“Power/ ” to confirm.

Auto mode

In automatic measurement mode, it will display “Auto” in the lower left corner of LCD, there maybe have

several kinds of measuring results, short press “Select/▼” to view different results until find the

corresponding result to fit the testing sample. If the given results are all incorrect, long press “Select/▼” to

shift to the Manual mode and make a new measurement.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 4 of 8

Manual mode

A. If select manual mode, short press “Power/ ” will confirm and enter into the material type setting

interface, the default setting of first layer is glass, from the second layer, there are three options:

glass, air and none. Short press “Power/ ” to switch to set next layer. No need to set the laminate

inner-layer because the meter can’t measure the thickness of laminate inner-layer of laminated glass.

The thickness of laminate inner-layer will be included in the thickness value of adjacent glass.

B. After setting the material type, if the next layer is “none”, short press “Power/ ” will enter into the

thickness setting interface. Preset the estimated thickness value for current layer, short press

“Measure/▲” to increase the number by 1, short press “Select/▼” to reduce the number by 1. Short

press “Power/ ” to switch to next layer.

C. After setting the thickness, short press “Power/ ” will enter into save setting interface. Short press

“Measure/▲” and “Select/▼” to select save, reset or exit, then short press “Power/ ” to confirm.

Preset the type Preset the thickness Save setting interface

”Auto” mode is suitable for the measurement of most kinds of glass. Normally, the Meter will show several

different measurement result, the first one is the most likely result.

The first result The second result The third result

For some special glass, in “AUTO” mode can not get the correct result, "Manual" mode can be used. In

the "Manual” mode, preset the estimated glass thickness and air layer thickness. There is only one

measurement result to get in “Manual” mode.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 5 of 8

Triple glazing Double glazing

Laminated glass with one layer air Laminated glass

V. Measuring Operations

Attach the back of the instrument closely to the tested glass surface, short press “Measure/▲”to enter

into the measuring state, Maybe there are several kinds of results, short press “Select/▼” to view different

results.

In “Auto” mode, the measuring result of Triple glazing as shown below:

“Glass1”is the thickness of the first layer of glass, the measured value is 5.88mm;

”Air1”is the thickness of the first layer of air space, the measured value is 12.75mm;

”Glass2”is the thickness of the second layer of glass, the measured value is 5.91mm;

”Air2”is the thickness of the second layer of air space, the measured value is 12.64mm;

”Glass3”is the thickness of the third layer of glass, the measured value is 5.9mm.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 6 of 8

In the “Manual” mode, the measuring result of laminated glass as shown below:

“G1“means the first layer of glass, “G2“means the second layer of glass, and “G1+G2“means the

total thickness value of two layers of glass, the measured value is 8.31mm. This

result(G1+G2)means it’s unable to identify the position of the laminate inner-layer.

If the meter display the following image, that means it’s unable to identify glass, The possible causes

are listed below:

a) The back of instrument doesn’t attach closely to the tested glass surface;

b) The reflectivity of LOW-E layer is too high(More than 70%), please try to measure another

surface of glass;

c) The sunlight is too strong, try to prevent the back of the meter from directly facing the sunlight;

d) The surface of glass is too dirty or it is scratched.

VI. Precautions

1. Keep the glass surface clean.

2. Try to avoid overlapping of several glass when measuring, which may lead to wrong measuring

results.

3. Keep the detector on the back of the instrument clean.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 7 of 8

4. In order to improve the measurement accuracy, try to prevent the back of the meter from directly

facing the sunlight.

5. This product emits a laser beam from the back side. Do not point the laser at anyone’s eyes.

6. Avoid contact with corrosive substances and keep from high temperature and high humidity

environment.

7. While the battery symbol is displayed as empty and flashing, please replace the batteries.

VII. Features

1. Laser reflects on CCD to measure glass thickness and air thickness from one side.

2. Quick measurement, the accuracy is up to 0.1mm.

3. It can test thickness of triple glazing, double glazing, laminated glass and other kinds of glass.

VIII. Standard Packing List

No.

Description

Quantity

Unit

Digital Glass Thickness Meter

pcs

User Manual

pcs

Certificate / warranty card

pcs

Plastic case

pcs

AAA batteries

pcs

IX. Service

1. The meter has one-year warranty. If the meter works abnormally, please send the whole meter to the

company for maintenance.

2. Provide users with spare parts and lifelong maintenance services.

3. Provide the users with the meter inspection service for free.

4. Free technical support for long term.

Manufacturer: Shenzhen Linshang Technology Co.,Ltd.

Website: www.linshangtech.com

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 8 of 8

Service hotline: 086-755-86263411

Email: [email protected]

Inhaltsverzeichnis

Andere LINSHANG Messgerät Handbücher

LINSHANG

LINSHANG LS192 Bedienungsanleitung

LINSHANG

LINSHANG LS163 Bedienungsanleitung

LINSHANG

LINSHANG LS110H Technisches Handbuch

LINSHANG

LINSHANG LS220B Bedienungsanleitung

LINSHANG

LINSHANG LS212 Bedienungsanleitung

LINSHANG

LINSHANG LS200 Bedienungsanleitung

LINSHANG

LINSHANG LS125 Bedienungsanleitung

LINSHANG

LINSHANG LS196 Bedienungsanleitung

LINSHANG

LINSHANG LS182 Bedienungsanleitung

LINSHANG

LINSHANG LS170 Bedienungsanleitung

LINSHANG

LINSHANG LS190 Bedienungsanleitung

LINSHANG

LINSHANG LS195 Bedienungsanleitung

LINSHANG

LINSHANG LS126A Bedienungsanleitung

LINSHANG

LINSHANG LS160A Bedienungsanleitung

LINSHANG

LINSHANG LS132 Bedienungsanleitung

LINSHANG

LINSHANG LS213 Bedienungsanleitung

LINSHANG

LINSHANG LS162 Bedienungsanleitung

LINSHANG

LINSHANG LS171 Bedienungsanleitung

LINSHANG

LINSHANG LS101 Bedienungsanleitung

LINSHANG

LINSHANG LS120 Bedienungsanleitung

LINSHANG

LINSHANG LS123 Bedienungsanleitung

LINSHANG

LINSHANG LS220 Bedienungsanleitung

LINSHANG

LINSHANG LS136 Bedienungsanleitung

LINSHANG

LINSHANG LS137 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung