Lippert Components OneControl Hotspot Bedienungsanleitung

OneControl® Hotspot™

(Prepped)

OEM INSTALLATION MANUAL

Rev: 01.15.20 Page 2 CCD-0002221

TABLE OF CONTENTS

Introduction 2

Safety 2

Resources Required 3

Preparation 3

Installation 3

Notes 9

The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death

or serious personal injury if not performed safely and within the parameters set forth in this manual.

Failure to follow instructions provided in this manual may result in serious personal injury and/or

severe product and property damage, including voiding of the component warranty.

Unit MUST be supported per manufacturer's recommendations before working underneath. Failure

to do so may result in death or serious personal injury.

Always wear eye protection when performing service, maintenance or installation procedures.

Other safety equipment to consider would be hearing protection, gloves and possibly a full face

shield, depending on the nature of the task.

The "CAUTION" symbol above is a sign that a procedure has a safety risk involved and may cause

personal injury, product or unit damage if not performed safely and within the parameters set forth

in this manual.

Introduction

This document provides instructions for the installation of an OneControl HotspotTM prep kit. The installed

kit is intended as an optional upgrade for RV owners.

Safety

Read and understand all instructions before installing or operating this product. Adhere to all safety labels.

This manual provides general instructions. Many variables can change the circumstances of the instructions,

i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This

manual cannot begin to plot out instructions for every possibility, but provides the general instructions,

as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the

provided instructions may result in death, serious personal injury, severe product and/or property damage.

For information on the assembly or individual components of this product, please visit

https://support.lci1.com/electronics

NOTE: Images used in this document are for reference only when assembling, installing and/or operating

this product. Actual appearance of provided and/or purchased parts and assemblies may differ.

Rev: 01.15.20 Page 3 CCD-0002221

Moving parts can pinch, crush or cut. Keep clear and use caution.

Resources Required

Fig. 1

• 1-2 people, depending on the task

• Cordless or electric drill or screw gun

• Appropriate drill bits

• Appropriate drive bits

• Sharp cutting tool

• All weather silicone sealant

• Tape measure

• Straightedge

• Non-permanent marking method

• Strain reliefs for electrical wire

• Four #8 x ¾" stainless steel Phillips pan head screws

Preparation

1. Make sure unit is supported in accordance with manufacturer's recommendations.

2. Make sure the mounting surfaces for the internal prep plate (Fig. 1A) and external cellular antenna

prep plate (Fig. 1B) are flat and clean—free of dust, grime and oils.

Installation

NOTE: Orange lines indicate where material is being removed, either by cutting, grinding or some other

method. Green lines indicate a designated area. White lines with black borders indicate where

marking on an object with a permanent or non-permanent marking method is required.

Rev: 01.15.20 Page 4 CCD-0002221

1. Locate an area within the unit where the internal prep plate (Fig. 1A) can best be mounted.

NOTE: Keep in mind when installing the internal prep plate that the future install of the Hotspot system

will need to be installed on a flat surface area and be located within 12" of the internal prep plate.

2. If desired, create a template out of durable material, and similar to the dimensions specified in figure 2,

for the installation location of the internal prep plate.

NOTE: Dimensions subject to change.

3. Place the internal prep plate template flat and level against the designated mounting location to:

A. Mark the center of the three ⁄" diameter holes (Fig. 2).

B. Set the drill template aside.

C. Drill one 1 ⁄" diameter access hole through the center hole (Fig. 2).

Fig. 2

2 ¾"

4 ½"

⁄" Dia.

1 ⁄" Dia.

⁄" Dia.

Rev: 01.15.20 Page 5 CCD-0002221

4. Loosely place the internal prep plate assembly (Fig. 3) into the access hole.

A. Connect the electrical wires of the DC jack harness (Fig. 3A) to the power and ground circuitry.

B. Let the internal prep plate and DC jack harness lay loose across the access hole.

5. Position the external cellular antenna prep plate (Fig. 4) in the desired mounting location on the roof of

the unit, close to the approximate location to where the internal prep plate (Fig. 3) is located.

A. Make sure the external cellular antenna prep plate can lay flat against the roof's surface.

B. With a non-permanent marking method, trace an outline along the outer lip of the external cellular

antenna prep plate (Fig. 4A) on the roof's surface. Set the external cellular antenna prep plate aside

for future installation.

C. Using the point of the hole (Fig. 4B) where the coaxial cables will rest, as the starting point,

measure to the middle right side of the of the external cellular antenna prep plate. The

measurement should be approximately 8".

D. Measure and mark the same distance in step 5C on the trace outline of the roof's surface.

Measure from the middle right side in towards the center, mark the location on the roof's surface.

E. Using the point of the hole (Fig. 4B) where the coaxial cables will rest, as the starting point,

measure to the bottom side of the of the external cellular antenna prep plate. The measurement

should be approximately 3 3/4".

Fig. 4

Fig. 3

3 ¾"

Rev: 01.15.20 Page 6 CCD-0002221

8. Place one end of each coaxial cable (Fig. 6A) to the hole of the external cellular antenna prep plate

(Fig. 6B) and slide the wires (Fig. 6C) into the far end of the slot area (Fig. 6D) to keep the wires in place.

Fig. 5

F. Measure and mark the same distance in step 5E on the trace outline of the roof's surface.

Measure from the bottom side up towards the center, mark the location on the roof's surface.

6. Before any cuts are made to the roof of the unit:

A. Make sure the supplied coaxial cables will reach from the roof antenna's marked location to the

internal prep plate.

B. Make sure that there are no wires, pipes or tubing underneath the marked areas before cutting

and drilling.

7. Using the center point of the intersecting lines (Fig. 4B), use a sharp cutting tool to crosscut the rubber

roof 3/4"in each direction (Fig. 5A—orange lines).

A. Peel the corners of the rubber roof back.

B. Drill a 1/2" inch hole (Fig. 5B—orange circle) at the center of the cuts. This is the cellular antenna

coaxial cable access hole for passing the cables through the unit to the internal prep plate.

Fig. 6

Rev: 01.15.20 Page 7 CCD-0002221

9. Apply all-weather silicone sealant (Fig. 7A—green line) to the underside of the external cellular

antenna prep plate, around the entire outer lip. Do not leave any gaps in the sealant to ensure a good

seal to the mounting surface.

Fig. 7

10. Thread the opposite ends of the cables through the drilled access hole in the roof. Carefully guide

the coaxial cables through the hole as the external cellular antenna prep plate is gently placed

onto the roof.

11. After the external cellular antenna prep plate is in place, use four #8 x ¾” stainless steel Phillips pan

head screws (Fig. 8A) to secure the external cellular antenna prep plate to the roof. Do not over-tighten

the screws.

NOTE: The silicone sealant will spread out slightly as the tightening of the screws draw down the external

cellular antenna prep plate.

12. An additional, continuous bead of all-weather silicone sealant should be placed around the outer lip

of the external cellular antenna prep plate (Fig. 9A—green line) and over the four mounting screws to

form a watertight seal. Allow silicone sealant to dry completely.

NOTE: DO NOT place silicone sealant on the top removeable lid or screws (Fig. 9B) of the external cellular

antenna prep plate. The gasket underneath the lid of the external cellular antenna prep plate

effectively makes the external cellular antenna prep plate waterproof and ready for easy future

installation of the external cellular antenna.

Fig. 8

Fig. 9

Rev: 01.15.20 Page 8 CCD-0002221

15. Place any excess coaxial cable into the area behind the internal prep plate. Secure excess cabling with

strain reliefs.

16. Place the internal prep plate flush against the wall, taking care to align the plate's two mounting holes

with the previously marked screw locations.

17. Install two #8 x ¾” stainless steel Phillips pan head screws (Fig. 11A) to secure the internal prep plate

to the wall.

Fig. 11

13. Feed the two cellular antenna coaxial cables through the unit and into the internal prep plate access hole.

14. Attach each coaxial cable to a coaxial bulkhead connector located on the back of the internal prep

plate (Fig. 10A).

Fig. 10

Installed DC Jack Harness not shown for clarity.

Rev: 01.15.20 Page 9 CCD-0002221

Notes

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).

LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an

authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.

The information contained in this manual is subject to change without notice and at the sole discretion of LCI.

Revised editions are available for free download from lci1.com.

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: (574) 537-8900 | Web: lci1.com | Email: [email protected]

Andere Handbücher für OneControl Hotspot

Inhaltsverzeichnis

Andere Lippert Components Autozubehör Handbücher

Lippert Components

Lippert Components Jack-It Bedienungsanleitung

Lippert Components

Lippert Components Sliding Swivel Seat Base Bedienungsanleitung

Lippert Components

Lippert Components In-Wall Slide-Out Bedienungsanleitung

Lippert Components

Lippert Components Solera Power Awning Regal Head Gebrauchs- und Pflegehandbuch

Lippert Components

Lippert Components Solera Slide Topper Bedienungsanleitung

Lippert Components

Lippert Components Ground Control 2.0 Bedienungsanleitung

Lippert Components

Lippert Components SOLERA SLIDER Bedienungsanleitung

Lippert Components

Lippert Components X-Trek Bedienungsanleitung

Lippert Components

Lippert Components Solera Power Awning Gebrauchs- und Pflegehandbuch

Lippert Components

Lippert Components ground control 3.0 Bedienungsanleitung

Lippert Components

Lippert Components Solera Bedienungsanleitung

Lippert Components

Lippert Components PSX1 Gebrauchs- und Pflegehandbuch

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Bedienungsanleitung

Lippert Components

Lippert Components Solera Power Awning Gebrauchs- und Pflegehandbuch

Lippert Components

Lippert Components Jack-It Bedienungsanleitung

Lippert Components

Lippert Components Happijac Bedienungsanleitung

Lippert Components

Lippert Components Innolight Sliding Montageanleitung

Lippert Components

Lippert Components Solera Classic Montageanleitung

Lippert Components

Lippert Components A-Frame Coupler Montageanleitung

Lippert Components

Lippert Components SURESHADE POWER BIMINI Bedienungsanleitung

Lippert Components

Lippert Components Solera Montageanleitung

Lippert Components

Lippert Components ABOVE FLOOR SLIDEOUT SYSTEM Bedienungsanleitung

Lippert Components

Lippert Components SolidStep XF Bedienungsanleitung

Lippert Components

Lippert Components COACH STEP Einrichtungshandbuch

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung