Lutron Electronics LCR-9063 Bedienungsanleitung

TABLE OF CONTENTS

1. FEATURES .............................................................. 1

2. SPECIFICATIONS ....................................................

2-1 General Specifications ........................................

2-2 Electrical specifications .......................................2

A. Inductance.......................................................2

B. Capacitance range ........................................... 2

C. Resistance range ............................................. 3

3. FRONT PANEL DESCRIPTION ...................................4

4. INDUCTANCE (L) MEASURING PROCEDURE ..............5

5. CAPACITANCE (C) MEASURING PROCEDURE ............ 6

6. RESITANCE (R) MEASURING PROCEDURE ................ 8

7. MAINTENANCE ......................................................

8. BATTERY REPLACEMENT ......................................... 9

1. FEATURES

* A pocket, Battery operated, Inductance, Capacitance and

Resistance Meter.

* LSI-circuit provides high reliability and durability.

* LCD display for clear readout even in bright ambient

light conditions.

* Input overload protection .

* Rotary switch function selector .

or-co

pane

or easy

tifi

on o

unc

ons

and ranges .

* Low battery indicator.

2. SPECIFICATIONS

2-1 General Specifications

Display 13 mm (0.5") LCD, 3 1/2 digits.

Max. reading 1999.

Over-input " 1 " mark indication.

indicator

Sampling Time Approx. 0.4 second.

Operating 0 蚓to 50 蚓(32 蚌to 122 蚌).

Temp.

Operating Less than 80% RH.

Humidity

Power Supply 006 P DC 9V battery, heavy duty battery.

Dimensions 120 x 72 x 37 mm .

Weight 185 g/0.41 LB.

Power R - Approx. 8 mA.

Consumption L - Approx. 9 mA.

C - Approx. 9 mA.

Accessories Instruction Manual .................1 PC

Included

est alli

ator clips ..................1 pair

2-2 Electrical specifications ( 23 5 C )

A. Inductance

Range

In-range Reso-

ccuracy Inducto

Display lution

Resistanc

Limitatio

* 2 mH 0.02 mH-2 mH 1 uH 3%+3d) < 2 ohm

20 mH 2 mH-20 mH 10 uH < 100 ohm

200 mH 20 mH-200 mH 100 uH

2 H 0.2 H-2 H 1 mH 5%+5d) < 500 ohm

20 H 2 H-20 H 10 mH

@ uH = micro Henry (10 -6H), mH = mili Henry (10 -3H).　　

@ Test

requency : Approx. 250 Hz.

Zero stray in

uctance o

2 mH ran

(

ort circuit

)

:0 uH.

e exact measurin

or t

e 2 mH ran

e, s

rea

e meter

s rea

ue, t

uct t

e Zero stray

uctance va

(

ort circuit va

)

. For examp

e : T

meter

s rea

is 7 uH, t

e s

ort va

ue is -15 uH,

e exact measurin

ue is 7 uH -

(

-15 uH

)

= 22 uH.

B. Capacitance

Range

In-range Reso- Test Fre-

ccuracy

Display lution quency

* 2 nF 10 pF-2 nF 1 pF 250 Hz

20 nF 200 pF-20 nF 10 pF 250 Hz

200 nF 2 nF - 200 nF 100 pF 250 Hz (3 % + 3 d)

2 uF .02 uF - 2 uF 1 nF 250 Hz

20 uF 0.2 uF - 20 uF 10 nF 250 Hz

200 uF 2 uF - 200 uF 100 nF 40 Hz

pF= pico Farad (10 -12F)　nF= nano Farad (10 -9F)　

uF= micro Farad (10 -6F)　

Zero stray capacitance o

2 nF ran

(

open circui

30 pF

e exact measurin

or t

e 2 nF ran

e, s

rea

e meter

s rea

ue, t

uct t

e Zero stray

capacitance va

(

open circuit va

)

. For examp

e : T

meter

s rea

is 32 pF, t

e open circuit va

ue is 12 pF,

e exact measurin

ue is 32 pF - 12 pF = 20 pF.

C. Resistance

Range

Resolution Open

Accuracy

Circuit

Voltage

200 ohm 0.1 ohm

2 k 1 ohm Approx.

20 k 10 ohm 600 mV ( 2 % + 3 d )

200 k 100 ohm

2000 k 1 k

20 M 10 k Approx.

300 mV

Remark

hou

h the internal test frequency is approx. 250 Hz.

However the accuracy ad

ustment are executed as

* For the capacitance ( 2 uF, 200 nF, 20 nF, 2 nF ) ran

the acuracy ad

ustment is compared with the " Standard

capacitor that tested under the 1 KHz frequency ".

* For the capacitance ( 20 uF, 200 uF ) ran

e, the

accuracy ad

ustment is compared with the " Standard

capacitor that tested on the 100 Hz frequency ".

* For the inductance ( 2 mH, 20 mH, 200 mH, 2 H ) ran

the accuracy ad

ustment is compared the " Standard

inductor that tested on the 1 KHz ".

* For the inductance ( 20 H ) ran

e, the calibration is

compared the " Standard inductor that tested on the

100 Hz ".

he above spec. accuracy are tested under th

environment RF Field Stren

th less than 3 V/M & frequenc

less than the 30 MHz only.

4. INDUCTANCE (L) MEASURING

PROCEDURE

1)Slide the " Power On/Off switch " (3-2, Fig. 1) to the " 1 "

position.

" 1 " = On " 0 " = Off

2)Slide the " L/C,R switch " ( 3-4, Fig. 1 ) to the " L/C "

position.

3)Rotate the function switch for the maximum expected

inductance range.

4)Plug the " Test alligator clips " to the " Measuring input "

(3-5, Fig.1), then connect the inductor to the alligator

clips.

5)Read the display. The value indicated corresponds to

the range selected. If the DISPLAY shows "1", it

indicates an Out-of-Range measurement. In order

to improve the resolution, Select the next higher range.

NOTE:

1) *

If the inductance value is unmarked start

with the Lower range ( 2 mH ) and keep

increasing until a suitable reading is

obtained.

2)*

For the 200 mH range are designed for measuring

from 20 mH to 200 mH only. It is normal, if get the no

convineant reading value when measue inductance less

than 20 mH of 200 mH range.

For the 2H range are designed for measuring from 0.2 H

to 2H only. It is normal, if get the no convineant

reading value when measue inductance less than 0.2 H

of 2 H range.

For the 20H range are designed for measuring from

2 H to 20H only. It is normal, if get the no convineant

reading value when measue inductance less than 2 H

of 20 H range.

3)Consideration for internal circuit's stray inductance of 2

mH range, if intend to make the precision measurement,

should short the input terminal first, record the display

Then final true measurement value will be the " reading

value " deduct above " internal circuit stray inductance "

For example : If the stray inductance is -15 uH, then the

real real value is the reading value plus 15 uH ( deduct

-15 uH ).

4)Measurement of very low inductance should be

performed using extremely short leads in order to avoid

introducing any stray capacitance.

5)This instruments is not intended for determining the "Q"

factor for the inductor. Misleading readings may be

obtained if the measurement of the inductance of a

resistor is attempted.

5. CAPACITANCE (C) MEASUREMENT

PROCEDURE

1)Slide the " Power On/Off switch " (3-2, Fig. 1) to the " 1 "

position.

" 1 " = On " 0 " = Off

2)Slide the " L/C,R switch " ( 3-4, Fig. 1 ) to the " L/C "

position.

3)Rotate the function switch for the maximum expected

capacitance range.

4)Plug the " Test alligator clips " to the " Measuring input "

(3-5, Fig.1), then connect the inductor to the alligator

clips.

Observe polarity when connecting polarized

capacitors.

Fully discharge any charged capacitors.

5)Read the display. The value indicated corresponds to

the range selected. If the DISPLAY shows "1", it

indicates an Out-of-Range measurement. In order

to improve the resolution, Select the next higher range.

NOTE:

1) *

If the capacitance value is unmarked start

with the Lower range ( 2 nF ) and keep

increasing until a suitable reading is

obtained.

2)*

For the 200 nF range are designed for measuring from

2 nF to 200 nF only.

For the 2 uF range are designed for measuring from

0.02 uF to 2 uF only.

For the 20 uF range are designed for measuring from

0.2 uF to 20 uF only.

For the 200 uF range are designed for measuring from

2 uF to 200 uF only.

It is normal, if get the no convineant reading

value when measue capacitacitance :

< 2 nF of 200 nF range.

< 0.02 uF of 2 uF range.

< 0.2 uF of 20 uF range.

< 2 uF of 200 uF range.

3)Consideration for internal circuit's stray capacitance of 2

nF range, if intend to make the precision measurement,

should open the test alligators (not connect the measuring

capacitor ), record the display (for example 15 uF ..... it is

the circuit's stray capacitance). Then final true

measurement value will be the " reading value " deduct

above " internal circuit stray capacitance "

4) A capacitor with low voltage leakage will read over range,

or a much higher value than normal. An open circuit

capacitor will read zero on all ranges (possibly a few pF

on 2nF range, due to stray capacitance of the instrument).

5)Measurement of very low capacitance should be

performed using extremely short leads in order to avoid

introducing any stray capacitance.

6)When using the test leads, remember that the leads may

introduce a measurable capacitance to the measurement.

Capacitors, especially electrolytics, often have notoriously

wide tolerances.

6. RESISTANCE (R) MEASUREMENT

PROCEDURE

1)Slide the " Power On/Off switch " (3-2, Fig. 1) to the " 1 "

position.

2)Slide the " L/C,R switch " ( 3-4, Fig. 1 ) to the " R "

position.

3)Rotate the function switch for the maximum expected

inductance range.

4)Plug the " Test alligator clips " to the " Measuring input "

(3-5, Fig.1), then connect the inductor to the alligator

clips.

5)Read the display. The value indicated corresponds to

the range selected. If the DISPLAY shows "1", it

indicates an Out-of-Range measurement. In order

to improve the resolution, Select the next higher range.

NOTE:

In order to make precision measurement at lower ranges,

deduct the stray resistance of measuring leads from the

readings. The stray resistance can be measured by

shorting the leads. 8

Inhaltsverzeichnis

Andere Lutron Electronics Messgerät Handbücher

Lutron Electronics

Lutron Electronics AM-4233SD Bedienungsanleitung

Lutron Electronics

Lutron Electronics DW-6095 Bedienungsanleitung

Lutron Electronics

Lutron Electronics GCH-2018 Bedienungsanleitung

Lutron Electronics

Lutron Electronics DW-6063 Bedienungsanleitung

Lutron Electronics

Lutron Electronics SL-4013 Bedienungsanleitung

Lutron Electronics

Lutron Electronics HR-3023SD Bedienungsanleitung

Lutron Electronics

Lutron Electronics SPM-1116SD Bedienungsanleitung

Lutron Electronics

Lutron Electronics DW-6195 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PCD-431 Bedienungsanleitung

Lutron Electronics

Lutron Electronics SP-82AC Bedienungsanleitung

Lutron Electronics

Lutron Electronics FORCE GAUGE FG-6005SD Bedienungsanleitung

Lutron Electronics

Lutron Electronics DT-2230 Bedienungsanleitung

Lutron Electronics

Lutron Electronics DW-6093 Bedienungsanleitung

Lutron Electronics

Lutron Electronics DW-6093 Bedienungsanleitung

Lutron Electronics

Lutron Electronics EMF-839 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PH-222 Bedienungsanleitung

Lutron Electronics

Lutron Electronics MG-3OO2 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Radio Powr Sav LRF2-DCRB Montage- und Bedienungsanleitung

Lutron Electronics

Lutron Electronics CD-4322 Bedienungsanleitung

Lutron Electronics

Lutron Electronics DS-9200 Bedienungsanleitung

Lutron Electronics

Lutron Electronics FR-5105 Bedienungsanleitung

Lutron Electronics

Lutron Electronics SOIL PH METER Bedienungsanleitung

Lutron Electronics

Lutron Electronics TU-2016 Bedienungsanleitung

Lutron Electronics

Lutron Electronics DM-9027T Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung