M-system M5SN Bedienungsanleitung

MODEL: M5SN

Super-mini Terminal Block Signal Conditioners M5-UNIT

INPUT LOOP POWERED ISOLATOR

Functions & Features

• Input-loop-powered design eliminates need for an output

loop power supply

• 350 Ω output drive

• High-density mounting

• CE marking

25 (.98)

(3.82)

41 (1.61)

mm (inch)

MODEL: M5SN-AA[1]

ORDERING INFORMATION

Specify a code from below for [1]

• Code number: M5SN-AA[1]

(e.g. M5SN-AA/Q)

• Specify the specification for option code /Q

(e.g. /C01 )

INPUT

Current

A: 4 – 20 mA DC

OUTPUT

Current

A: 4 – 20 mA DC

[1] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

GENERAL SPECIFICATIONS

Construction: Terminal block

Connection: M3.5 screw terminals (torque 0.8 N·m)

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output

Zero adjustment: -0.5 to +0.5 % (front)

Span adjustment: 98.5 to 101.5 % (front)

INPUT & OUTPUT

• Input 4 – 20 mA DC / Output 4 – 20 mA DC

Equivalent input impedance: 230 Ω plus load resistance

with 20 mA input

Operational range: 3 – 22 mA DC

(Accuracy is assured within 4 – 22 mA)

Load resistance: 350 Ω maximum; min. 50 Ω required for

adequate operation

INPUT CURRENT [mA]

4 12 20

10.0

VOLTAGE [V] ACROSS

INPUT TERMINALS

3.0

approx. 5.6

(load 50Ω)

6.0

12.0

approx. 5.0

8.0

approx. 3.8

approx. 9.6

(load 250Ω)

approx. 4.6

approx. 11.6

(load 350Ω)

INSTALLATION

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 0 to 90 %RH (non-condensing)

Mounting: DIN rail

Weight: 80 g (2.8 oz)

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)

Response time: Approx. 15 msec. (0 – 90 %)

Load effect: (factory-calibrated with 250 Ω load)

0.015 %/Ω (50 – 150 Ω)

0.003 %/Ω (150 – 350 Ω)

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength:

500 V AC @1 minute (input to output)

2000 V AC @1 minute (input or output to ground)

STANDARDS & APPROVALS

CE conformity:

EMC Directive (2004/108/EC)

EMI EN 61000-6-4: 2007

EMS EN 61000-6-2: 2005

Rugghölzli 2

CH - 5453 Busslingen Tel.+41 (0)56 222 38 18

Fax +41 (0)56 222 10 12 mailbox@sentronic.com

www.sentronic.com

Produkte, Support und Service

SENTRONICAG

MODEL: M5SN

DIMENSIONS unit: mm (inch)

94 (3.70)3 (.12)

25 (.98) 41 (1.61) [3.3 (.13)]

• When mounting, no extra space is needed between units.

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 (.29)

35.4 (1.39)

1 2

3 4

5 6

7 8

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

–

INPUT

–

OUTPUT

Inverter

Isolation

Load Effect

Compensation

Specifications are subject to change without notice.

Rugghölzli 2

CH - 5453 Busslingen Tel.+41 (0)56 222 38 18

Fax +41 (0)56 222 10 12 mailbox@sentronic.com

www.sentronic.com

Produkte, Support und Service

SENTRONICAG

M5SN

P. 1 / 2EM-2469 Rev.3

INPUT LOOP POWERED ISOLATOR MODEL M5SN

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Signal conditioner......................................................... (1)

■ MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■ GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the input

signal for safety.

■ ENVIRONMENT

• Indoor use

•When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufﬁcient ven-

tilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 0 to 90% RH

in order to ensure adequate life span and operation.

■ WIRING

•Do not install cables (input and output) close to noise

sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Install lightning surge protectors for those wires connect-

ed to remote locations. Choose a surge protector with its

maximum surge voltage 40V or less between lines. Rec-

ommended M-System model: MDP-24-1.

■ AND ....

•The unit is designed to function as soon as the input sig-

nal is supplied, however, a warm up for 10 minutes is re-

quired for satisfying complete performance described in

the data sheet.

COMPONENT IDENTIFICATION

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom.

■ MOUNTING THE UNIT ON A DIN RAIL

A) Hang the upper hook at the rear side of unit on the DIN

rail.

B) Push in the lower in keeping pressing the unit to the

DIN rail.

■ REMOVING THE UNIT

A) Push down the DIN rail adaptor using a minus screw-

driver.

B) Pull out the lower part of the unit.

C) Remove the upper part from the DIN rail.

Terminal Cover

Zero Adj.

Span Adj.

Body

Spec. Marking

DIN Rail

Spring Loaded

DIN Rail Adaptor

Rugghölzli 2

CH - 5453 Busslingen Tel.+41 (0)56 222 38 18

Fax +41 (0)56 222 10 12 mailbox@sentronic.com

www.sentronic.com

Produkte, Support und Service

SENTRONICAG

M5SN

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the con-

nection diagram on the front of the unit.

■ EXTERNAL DIMENSIONS unit: mm (inch)

■ CONNECTION DIAGRAM

94 (3.70)3 (.12)

25 (.98) 41 (1.61) [3.3 (.13)]

• When mounting, no extra space is needed between units.

35.4 (1.39)

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 (.29)

1 2

3 4

5 6

7 8

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Input: Check current with an ammeter. Be sure that

the connected transmitter allows the M5SN’s load value

[230Ω + output load resistance].

3) Output: Check that output load is within the permis-

sible limit of 50 to 350Ω.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the input signal on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

–

INPUT 3+

–

4OUTPUT

Rugghölzli 2

CH - 5453 Busslingen Tel.+41 (0)56 222 38 18

Fax +41 (0)56 222 10 12 mailbox@sentronic.com

www.sentronic.com

Produkte, Support und Service

SENTRONICAG

Andere M-system E/A-System Handbücher

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system R7F4HEIP-DAC16C Bedienungsanleitung

M-system

M-system R7D-YS2/UL Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R3-SS16N Bedienungsanleitung

M-system

M-system R7D-TS4/UL Bedienungsanleitung

M-system

M-system R7F4HC-DAC32C-K Bedienungsanleitung

M-system

M-system R3-MS4 Bedienungsanleitung

M-system

M-system R7L-DAC16 Bedienungsanleitung

M-system

M-system R30YN16A Bedienungsanleitung

M-system

M-system R7F4DC-DA16B-C Bedienungsanleitung

M-system

M-system R30SV2 Bedienungsanleitung

M-system

M-system R3-SS8N Bedienungsanleitung

M-system

M-system R30US4 Bedienungsanleitung

M-system

M-system R7F4DC-DA16A-J Bedienungsanleitung

M-system

M-system R5T-PA2 Bedienungsanleitung

M-system

M-system R3-DA8C Bedienungsanleitung

M-system

M-system M5SN-AA Bedienungsanleitung

M-system

M-system R7C-DC8C Bedienungsanleitung

M-system

M-system R7L-DC16A-R Bedienungsanleitung

M-system

M-system R80NCIT1 Bedienungsanleitung

M-system

M-system R7M-DA16F Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung