M-system R30YN16A Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9011 Rev.1 P. 1 / 4

INSTRUCTION MANUAL

DISCRETE OUTPUT MODULE

(NPN transistor output, 16 points) MODEL

R30YN16A

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Discrete output module.......................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•The equipment must be mounted inside the instrument

panel of a metal enclosure.

•The actual installation environments such as panel con-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrat-

ed in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■GENERAL PRECAUTIONS

•Before you remove the terminal block or mount it, turn off

output signals for safety.

■HOT INSERTION/REMOVAL OF MODULES

•It is possible to replace the module with the power sup-

plied, provided that modules are of the same model num-

ber and that the same Installation Base slot is used.

•Turn off output signals before replacing the module for

safety. Note that replacing multiple modules at once may

greatly change line voltage levels. We recommend that

you replace them one by one.

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

•Be sure to attach the terminal cover for safety.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

■OUTPUT AT THE LOSS OF COMMUNICATION

•Holds the output of the last normally received data.

•“Reset to 0” setting is not available.

R30YN16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9011 Rev.1 P. 2 / 4

COMPONENT IDENTIFICATION

RUN

ERR

RUN LED

Output Terminal Block

ERR LED

■FRONT VIEW

■BOTTOM VIEW

■SIDE VIEW

Lock Tab

Base Fixing Screw

Specifications

Positioning Guide

Terminal Cover

Discrete Output Indicator LEDs

Terminal Fixing

Screw

■STATUS INDICATOR LED

COLOR

FUNCTION

RUN Green ON in normal host communication

OFF in host communication error

ERR Red

OFF when internal bus operates normally

ON when an internal bus error occurs

Discrete Output Green ON when discrete output is ON

OFF when discrete output is OFF

■TERMINAL ASSIGNMENT

NO. ID FUNCTION NO.ID FUNCTION

1Y1Output 1 11 Y9 Output 9

2Y212 Y10 Output 10

3Y313 Y11 Output 11

4Y414 Y12 Output 12

5Y515 Y13 Output 13

6Y616 Y14 Output 14

7Y717 Y15 Output 15

8Y818 Y16 Output 16

9 24 V DC 19 V + 24 V DC

10 V –0V20V–0V

V +

Output 2

Output 3

Output 4

Output 5

Output 6

Output 7

Output 8

Y10

Y11

Y12

Y13

Y14

Y15

Y16

V+

V–

V+

V–

R30YN16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9011 Rev.1 P. 3 / 4

INSTALLATION

■INSTALLATION TO THE BASE

Use the Installation Base (model: R30BS).

The I/O slots are numbered in the ascending order starting

from the one on the immediate right side of the network

module (slot 1, slot 2...).

A code indicating the I/O slot number is assigned to each

I/O slot and I/O data is allocated in the order of this code.

When an I/O slot is vacant, blank data is sent or received to/

from the PLC, etc.

PWR COM I/O1 I/O n

■HOW TO MOUNT THE MODULE

1) Engage the positioning guide of the module with the In-

stallation Base.

2) Pivot the module on the positioning guide and press it

down until the lock tab sits into place.

Positioning Guide

3) Tighten the base ﬁxing screw using a screwdriver (stem

length: 70 mm/2.76” or more) (torque 0.5 N·m).

Base Fixing Screw

■HOW TO REMOVE THE MODULE

1) Loosen the base ﬁxing screw using a screwdriver (stem

length: 70 mm/2.76” or more).

Base Fixing Screw

2) While pressing the projection on the lock tab, push the

module upward.

3) Detach the positioning guide of the module from the In-

stallation Base.

Lock Tab

R30YN16A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9011 Rev.1 P. 4 / 4

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

①

②

③

④

⑪

⑫

⑬

⑭⑤

⑥

⑦

⑧

⑨

⑩

⑮

⑯

⑰

⑱

⑲

⑳

110 (4.33)

25 (.98) 98 (3.86)

20–M3

SCREW

(.24)

■CONNECTION DIAGRAM

Y10

V+

Y11

Y12

Y13

Y14

Y15

Y16

V-

V- –+

V+

V-

V- –+

Y16

BUS CONNECTOR

INTERNAL

BUS

INTERNAL

POWER

■Output Connection Example

WIRING INSTRUCTIONS

■TIGHTENING TORQUE

Separable screw terminal wiring screw: 0.5 N·m

Separable screw terminal ﬁxing screw: 0.5 N·m

■SOLDERLESS TERMINAL unit: mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.25 to 0.75 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

3.2 (.13) dia.

12 (.47) max.

6 max.

(.24)

3 (.12) max.

■HOW TO REMOVE SEPARABLE SCREW TERMINAL

The terminal block is separable in two pieces. Evenly loos-

en two screws on top and bottom of the terminal block to

separate.

Andere M-system E/A-System Handbücher

M-system

M-system R7C-DS4N Bedienungsanleitung

M-system

M-system R7HL-PA4E Bedienungsanleitung

M-system

M-system R5-SV Bedienungsanleitung

M-system

M-system R7ML-LC2 Bedienungsanleitung

M-system

M-system 6BSN Bedienungsanleitung

M-system

M-system R7M-TS4-R Bedienungsanleitung

M-system

M-system R1M-D1 Bedienungsanleitung

M-system

M-system R7M-DC4G-R Bedienungsanleitung

M-system

M-system R80NCIT1 Bedienungsanleitung

M-system

M-system R7E-PA8 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7F4HEIP-DAC16C Bedienungsanleitung

M-system

M-system R1M-GH2T Series Bedienungsanleitung

M-system

M-system R7F4DC-DAC16C-H Bedienungsanleitung

M-system

M-system R3-CT8B Bedienungsanleitung

M-system

M-system R5 Series Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system Devicenet R7F4HD-DA32B Bedienungsanleitung

M-system

M-system R7C-SV4 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R3-SS4 Bedienungsanleitung

M-system

M-system M5SN-AA Bedienungsanleitung

M-system

M-system 60C Bedienungsanleitung

M-system

M-system R7K4F Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung