M-system R8-SS4N Bedienungsanleitung
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9728 Rev.2 P. 1 / 5
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC current input module....................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures* to ensure the CE con-
formity.
* For example, installation of noise filters and clamp fil-
ters for the power source, input and output connected
to the unit, etc.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and input signal for safety.
• Switches on the side of the module can be set for mainte-
nance only while the power supply is off. Do not access
them while the power is supplied.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
A
B
• I/O Module
Confirm that the locking clamps of the I/O module are set.
Insert the module in parallel to the next one while aligning the grooves of
both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.
DC CURRENT INPUT MODULE
(4 points, non-isolated) MODEL R8-SS4N
R8-SS4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9728 Rev.2 P. 2 / 5
• Protective Cover
The protective cover is to be attached over the connected I/O module
at the right end.
Align the hooks on the cover with the grooves of the module and slide it
straight until the hooks are latched.
When removing the cover, pull it out while squeezing the hooks inward.
Groove
Hook
■HOW TO UNMOUNT THE MODULE ON DIN RAIL
Release the locking clamps and pull out straight the module.
Caution !
1) Be careful not to hurt your hand by pointed edges of the internal bus
connector.
2) I/O modules cannot hold tightly on the DIN rail by themselves without
power/network module.
Secure them to the position if necessary by using DIN rail end plates.
• Removing an intermediate module
R8-SS4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9728 Rev.2 P. 3 / 5
COMPONENT IDENTIFICATION
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
RUN
AI_I1
AI_I2
Module Address Setting
Rotary SW
Function Setting
DIP SW
Terminator DIP SW
SW1
x10
12345678
x1
SW2
SW4
SW3Term
On
On
Status Indicator LED
Input Status Indicator LED
Internal Bus Connector
Input Connectors
FRONT VIEW SIDE VIEW
CARD ADD.
AII1
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
■INDICATOR LED
ID OPERATION FUNCTION
Status OFF Stopping
Green ON Valid host communication
Green Blinking Reading/writing configuration
Red ON Setting error
Red Blinking Parameter error
Input
Status
OFF Input data in the range
Red Blinking Input data out of range
■INPUT CONNECTOR ASSIGNMENT
1
2
3
4
PIN
No. ID FUNCTION
1 + Input (+)
2 NC No connection
3 NC No connection
4 – Input (–)
■MODULE ADDRESS: SW1, 2
The left switch determines the tenth place digit, while the
right one does the ones place digit of the module address.
Address is selected between 0 to 30.
(Factory setting: 0)
Module Address Setting (x10)
Module Address Setting (x1)
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
■OPERATING MODE
(*) Factory setting
• Input Range: SW4-1, 4-2
Same setting for all channels. Use PC Configurator to set
independent ranges per channel.
INPUT RANGE SW4-1 SW4-2
0 − 20mA DC OFF OFF
4 − 20mA DC (*) ON OFF
• Conguration Mode: SW4-8
CONFIGURATION MODE SW4-8
DIP switch setting (*) OFF
PC Configurator and communication ON
Note: Be sure to set unused SW4-3 through 4-7 to OFF.
■TERMINATOR DIP SW: SW3
TERMINATOR SW SW3
Without (*) OFF
With ON
R8-SS4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9728 Rev.2 P. 4 / 5
PC CONFIGURATOR
The following parameter items can be configured with PC Configurator Software (model: R8CFG).
Refer to the users manual of the software for detailed operations.
■CHANNEL INDIVIDUAL SETTING
PARAMETER SETTING RANGE DEFAULT SETTING
Input Range -20 to +20 (mA DC) -20 to +20 (mA DC)
Lower range value -20.00 to +20.00 (mA) 4.00 (mA)
Upper range value -20.00 to +20.00 (mA) 20.00 (mA)
Fine zero adjustment -320.00 to +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 to +3.2000 1.0000
Scaled range Zero -32000 to +32000 0
Scaled range Span -32000 to +32000 10000
■CHANNEL BATCH SETTING
PARAMETER SETTING RANGE DEFAULT SETTING
Loss of internal bus communication detection time 0.0 to 99.9 (sec.) 1.0 (sec.)
Moving average (ver. 2.00 or later) Disable/Enable (8 times) Disable
Configuration mode DIP switch (OFF),
PC (ON)
DIP switch (OFF)
Note: Turn SW4-8 ON to allow programming by the PC Configurator via the Power/Network Module.
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
115 (4.53)6 (.24)7 (.28) 6 (.24) 7 (.28)
DIN RAIL
(35 mm wide)
[3 (.12)] [4 (.16)]
12 (.47) 59 (2.32)
55 (2.17)
R8-SS4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9728 Rev.2 P. 5 / 5
■CONNECTION DIAGRAM
1
2
4
3
INTERNAL POWER
INTERNAL BUS
EXC. SUPPLY *1
+
NC
NC
−
INPUT 1
+
NC
NC
−
INPUT 4
INPUT
CONNECTOR 1
1
2
4
3
INPUT
CONNECTOR 4
BUS CONNECTOR
*1. Not used
WIRING INSTRUCTIONS
■e-CON connector
Unit side connector: XN2D-1474-S002 (Omron)
Recommended cable side connector: XN2A-1470 (Omron)*1
Applicable wire size: 0.08 to 0.5 mm2(AWG28 to 20)
Outer sheath diameter: max. 1.5 dia
*1. The cable side connector is not included in the package.
Refer to the specifications of the product.
Inhaltsverzeichnis
Andere M-system E/A-System Handbücher
M-system
M-system R7F4DC-DA16A-J Bedienungsanleitung
M-system
M-system R8-PA4 Bedienungsanleitung
M-system
M-system R8-YVT4N Bedienungsanleitung
M-system
M-system R3-SV8A Bedienungsanleitung
M-system
M-system R3-TS4 Bedienungsanleitung
M-system
M-system M5XPHS Bedienungsanleitung
M-system
M-system R7ML-DA16 Bedienungsanleitung
M-system
M-system R7D-PA8 Bedienungsanleitung
M-system
M-system R7ML-DC16A-R Bedienungsanleitung
M-system
M-system R7D-RS4 Bedienungsanleitung
M-system
M-system Devicenet R7F4HD-DA32B Bedienungsanleitung
M-system
M-system R10M-CT4E Bedienungsanleitung
M-system
M-system R7F4HML3-D-DAC32B Bedienungsanleitung
M-system
M-system R3S-DA16 Bedienungsanleitung
M-system
M-system R7F4DC-DAC16D-H Bedienungsanleitung
M-system
M-system R7G4HEIP-6-DC16A Bedienungsanleitung
M-system
M-system R3-SV4A Bedienungsanleitung
M-system
M-system R7L-TS4 Bedienungsanleitung
M-system
M-system R3-SV8A Bedienungsanleitung
M-system
M-system R8-FS16N Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
