M-system R8-YVT4N Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 1 / 6

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and output signal for safety.

• Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Conﬁrm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning

the grooves of both modules (A & B in the above ﬁgure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

DC VOLTAGE OUTPUT MODULE

(4 points, non-isolated) MODEL

R8-YVT4N

R8-YVM4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 2 / 6

• Protective Cover

Groove

Hook

The protective cover is to be attached over the connected I/O

module at the right end.

Align the hooks on the cover with the grooves of the module

and slide it straight until the hooks are latched.

When removing the cover, pull it out while squeezing the

hooks inward.

■HOW TO UNMOUNT THE MODULE ON DIN RAIL

Release the locking clamps and pull out straight the mod-

ule.

• Removing an intermediate module

Caution !

1) Be careful not to hurt your hand by pointed edges of the

internal bus connector.

2) I/O modules cannot hold tightly on the DIN rail by them-

selves without power/network module.

Secure them to the position if necessary by using DIN

rail end plates.

R8-YVM4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 3 / 6

COMPONENT IDENTIFICATION

RUN

Function Setting

DIP SW

Terminator

DIP SW

12345678

SW4

SW3Term

■FRONT VIEW ■RIGHT VIEW

Status

Indicator LED

Output Status

Indicator LEDs

Internal Bus

Connector

Output

Connectors

Module Address Setting

Rotary SW

SW1

×10 CARD ADD. ×1

SW2

■INDICATOR LED

ID OPERATION FUNCTION

Status OFF Stopping

Green ON Valid host communication

Green Blinking Reading/writing conﬁguration

Red ON Setting error

Red Blinking Parameter error

Output

Status

OFF Output data in the range

Red Blinking Output data out of range

■OUTPUT CONNECTOR ASSIGNMENT

Ao 1

Ao 2

Ao 3

Ao 4

NO. ID FUNCTION

1 Ao 1 Output 1 (+)

2 AG Output 1 (-)

3 NC Unused

4 NC Unused

5 Ao 2 Output 2 (+)

6 AG Output 2 (-)

7 NC Unused

8 NC Unused

9 Ao 3 Output 3 (+)

10 AG Output 3 (-)

11 NC Unused

12 NC Unused

13 Ao 4 Output 4 (+)

14 AG Output 4 (-)

15 NC Unused

16 NC Unused

■MODULE ADDRESS: SW1, 2

The left switch determines the tenth place digit, while the

right one does the ones place digit of the module address.

Address is selected between 0 to 30.

(Factory setting: 0)

Module Address Setting (x10)

Module Address Setting (x1)

■OPERATING MODE

(*) Factory setting

• Range: SW4-1, 4-2

Same setting for all channels. Use PC Conﬁgurator to set

independent ranges per channel.

OUTPUT RANGE SW4-1 SW4-2

-10 − +10V DC (*) OFF OFF

0 − 10V DC ON OFF

0 − 5V DC OFF ON

1 − 5V DC ON ON

• Output at the Loss of Communication: SW4-7

Same output for all channels.

OUTPUT AT THE LOSS OF COMMUNICATION SW4-7

Output Hold (*)

(last data correctly received is hold)

OFF

Stop output ON

Note 1: For Stop output, output ﬁxed at -5% when conﬁgura-

tion mode is DIP switch setting.

Output ﬁxed at scaling value at the loss of communica-

tion when conﬁguration mode is PC.

R8-YVM4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 4 / 6

• Conguration Mode: SW4-8

CONFIGURATION MODE SW4-8

DIP switch setting (*) OFF

PC Conﬁgurator and communication ON

Note 2: Be sure to set unused SW4-3 through 4-6 to OFF.

■TERMINATOR DIP SW: SW3

TERMINATOR SW SW3

Without (*) OFF

With ON

PC CONFIGURATOR

The following parameter items can be conﬁgured with PC Conﬁgurator Software (model: R8CFG).

Refer to the users manual of the software for detailed operations.

■CHANNEL INDIVIDUAL SETTING

PARAMETER SETTING RAGNE DEFAULT SETTING

Output range -10 - 10 V DC -10 - +10 V DC

Lower range value -10.00 - +10 00 (V) -10.00 (V)

Upper range value -10.00 - +10 00 (V) 10.00 (V)

Fine zero adjustment -320.00 - +320.00 (%) 0.00 (%)

Fine gain adjustment -3.2000 - +3.2000 1.0000

Scaled range Zero -32000 - +32000 0

Scaled range Span -32000 - +32000 10000

Initial output at the startup (scaled range) -32000 - +32000 0

Fixed output at the loss of comunication (scaled range) -32000 - +32000 -500

■CHANNEL BATCH SETTING

PARAMETER SETTING RAGNE DEFAULT SETTING

Loss of internal bus communication detection time 0.0 – 99.9 (sec.) 1.0 (sec.)

Output function at the loss of communication Hold the last normally received data

Fixed output as speciﬁed

Hold the last normally

received data

Conﬁguration mode DIP SW (OFF)

PC (ON)

DIP SW (OFF)

Note. Be sure to set SW4-8 to ON to conﬁgure output range and output at the loss of communication by the PC conﬁgurator.

Settings are programmed by the PC Conﬁgurator via the Power/Network Module.

R8-YVM4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 5 / 6

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm [inch]

115 (4.53)

6 (.24)7 (.28) 6 (.24) 7 (.28)

DIN RAIL

(35mm wide)

(3 (.12)) (4 (.16))

12 (.47) 73 (2.87)

55 (2.17)

■CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY *1

*1. Not used

OUTPUT CONNECTOR 1

Ao1

Ao2

Ao3

Ao4

OUTPUT 1

OUTPUT CONNECTOR 3

OUTPUT CONNECTOR 4

OUTPUT CONNECTOR 2

BUS CONNECTOR

OUTPUT 2

OUTPUT 3

OUTPUT 4

R8-YVM4N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9672 P. 6 / 6

WIRING INSTRUCTIONS

■TENSION CLAMP

Unit side connector: M-System’s product

Cable side connector: DFMC1,5/2-ST-3,5 (Phoenix Contact)

(included in the package)

Applicable wire size: 0.2 - 1.5 mm2

Stripped length: 10 mm

Recommended solderless terminal

• AI0,25-10YE 0.25 mm2(Phoenix Contact)

• AI0,34-10TQ 0.34 mm2(Phoenix Contact)

• AI0,5-10WH 0.5 mm2(Phoenix Contact)

• AI0,75-10GY 0.75 mm2(Phoenix Contact)

• A1-10 1.0 mm2(Phoenix Contact)

• A1,5-10 1.5 mm2(Phoenix Contact)

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R7E-EC8A Bedienungsanleitung

M-system

M-system R7D-SV4 Bedienungsanleitung

M-system

M-system R7F4DC-DA16B-C Bedienungsanleitung

M-system

M-system R7I4DML3-DC32A Bedienungsanleitung

M-system

M-system R3-SS8 Bedienungsanleitung

M-system

M-system R3-CT8C Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R8-DCM16ALZ Bedienungsanleitung

M-system

M-system R7ML-LC2 Bedienungsanleitung

M-system

M-system R3-CT8B Bedienungsanleitung

M-system

M-system R7M-DA16-R Bedienungsanleitung

M-system

M-system R7E-PA8-R Bedienungsanleitung

M-system

M-system R7D-TS4 Bedienungsanleitung

M-system

M-system R7ML-SV4 Bedienungsanleitung

M-system

M-system R7C-YS4 Bedienungsanleitung

M-system

M-system R30SVF4 Bedienungsanleitung

M-system

M-system R3-MS4 Bedienungsanleitung

M-system

M-system R30SV2 Bedienungsanleitung

M-system

M-system R7D-DC16B Bedienungsanleitung

M-system

M-system R7F4HC-DC32A-K Bedienungsanleitung

M-system

M-system R7D-RS4 Bedienungsanleitung

M-system

M-system Devicenet R7F4HD-DA32B Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DAC16C-H Bedienungsanleitung

M-system

M-system R3-TS8 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung