M-system R7C-YV4 Bedienungsanleitung

EM-7801-AD P. 1 / 9

INSTRUCTION MANUAL

DC VOLTAGE OUTPUT MODULE, 4 points

(CC-Link V.1.10) MODEL R7C-YV4

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANG

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V AC rating: 24V ±10%, 50/60Hz, approx. 180mA

24V DC rating: 24V ±10%, approx. 90mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and output signal for safety.

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 2 / 9

COMPONENT IDENTIFICATION

ERR RD

RUN SD

PWR X10 X1

STATION ADD. B.RATE

CNFG.

12345678

4567

123234

789

(A) Status Indicator LED *1

(B) Station Address Setting Rotary SW

(D) Operating Mode Setting DIP SW (SW1)

(E) PC Configurator Jack

(F) CC-Link, Power Supply Terminals

(G) Output Terminals

(H) Terminating Resistor SW

*1. Refer to ‘Status Indicator LED’ section for detailed information.

(A)

(F) (G)

(B) (C) (D) (E)

TERM

ON OFF

■ SIDE VIEW

■ FRONT VIEW

(H)

■STATUS INDICATOR LED

ID COLOR FUNCTION

PWR Red Turns on when the internal 5V is sup-

plied normally.

RUN Red Turns on when the refresh data is re-

ceived normally.

ERR Red Turns on when the received data is

abnormal.

SD Red Turns on when the module is transmit-

ting.

RD Red Turns on when the module is receiving.

■STATION ADDRESS

Station Address is selected between 1 and 64 in decimal.

The left switch determines the tenth place digit, while the

right switch does the ones place digit of the address.

Station Address Setting (x1)

Station Address Setting (x10)

■BAUD RATE

Baud Rate is selected with the rotary switch.

Baud Rate Setting

0 : 156 kbps

1 : 625 kbps

2 : 2.5 Mbps

3 : 5 Mbps

4 : 10 Mbps

■OPERATING MODE

(*) Factory setting

• Output at the loss of communication (SW1-4)

SW1-4 OUTPUT AT THE LOSS OF COMMUNICATION

OFF Reset the output (to -15% or approx. -11.5V DC)

ON Hold the output (*)

(maintains the last data received normally)

• Output range (SW1-5, 1-6, 1-7, 1-8)

SW1-5 SW1-6 SW1-7 SW1-8 OUTPUT RANGE

OFF OFF OFF OFF -10 – +10V DC (*)

ON OFF OFF OFF -5 – +5V DC

ON ON OFF OFF 0 – 10V DC

OFF OFF ON OFF 0 – 5V DC

ON OFF ON OFF 1 – 5V DC

ON ON ON ON

PC Conﬁgurator setting

Note : Be sure to set unused SW1-1 through 1-3 to OFF.

■POWER SUPPLY, CC-LINK TERMINAL ASSIGNMENT

U(+)

SLD

V(–)

NO. ID FUNCTION, NOTES

1 DB White

2 SLD Shield

3 FG FG

4 DA Blue

5 DG Yellow

6 U(+) Power input

7 V(–) Power input

■OUTPUT TERMINAL ASSIGNMENT

789

COM3

COM0

V0 V1 V2

COM1 COM2

NO. ID FUNCTION NO. ID FUNCTION

1 NC No connection 6 NC No connection

2 COM0 Common 0 7 V0 Voltage output 0

3 COM1 Common 1 8 V1 Voltage output 1

4 COM2 Common 2 9 V2 Voltage output 2

5 COM3 Common 3 10 V3 Voltage output 3

■TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and

OFF to invalidate. (Factory setting OFF)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 3 / 9

INDICATOR LED

■STATUS INDICATOR LED

PWR RUN ERR SD *1RD STATUS *2

ON ON BL BL ON Communicates normally with occasional CRC errors due to noise interference.

ON ON BL BL ON Communicates normally but the Baud Rate and/or Station Address switches failed.

ERR LED blinks approximately in 0.5 seconds intervals.

ON ON BL BL OFF ----

ON ON BL OFF ON CRC error found in the received data. Unable to respond.

ON ON BL OFF OFF ----

ON ON OFF BL ON Normal communication

ON ON OFF BL OFF ----

ON ON OFF OFF ON Unable to receive data addressed to the station.

ON ON OFF OFF OFF ----

ON OFF BL BL ON Performs the interval-timed responses but CRC error found in receiving the refresh

data.

ON OFF BL BL OFF ----

ON OFF BL OFF ON CRC error found in the data addressed to the station.

ON OFF BL OFF OFF ----

ON OFF OFF BL ON Link is not started.

ON OFF OFF BL OFF ----

ON OFF OFF OFF ON No data addressed to the station. Or unable to receive data addressed to the station

due to noise interference. (Missing parts of the data sent from the master)

ON OFF OFF OFF OFF Unable to receive data due to wire breakdown

ON OFF ON OFF

ON/OFF

Faulty Baud Rate and/or Station Address setting

OFF OFF OFF OFF OFF Power input removed. Or power supply failure.

OFF = OFF, ON = ON, BL = Blinking

*1. SD LED may look not blinking but ON with high baud rate and fewer connected modules.

*2. LEDs indicated with “----” in STATUS rarely occurs in normal operation (LED failure or the like as possible cause).

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R7CON for detailed operation.

■INTERFACE MODULE SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Communication Timeout 0.0 – 3276.7 (sec.) 1.0 (sec.)

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Output Range -10 to +10 V DC

-5 to +5 V DC

0 to 10 V DC

0 to 5 V DC

1 to 5 V DC

-10 to +10 V DC

Zero scale -32000 to +32000 0

Full scale -32000 to +32000 10000

Bias -320.00 to +320.00 0.00

Gain -3.2000 to +3.2000 1.0000

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 4 / 9

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

23415

789

4567

123

3 (.12)5.5 (.22)

7–M3 SCREW

TERMINALS

for CC-Link, POWER

10–M3 SCREW

TERMINALS

for OUTPUT

6 (.24)

50 (1.97)

6 (.24)

18.5 (.73)

115 (4.53)

DIN RAIL

35mm wide

[5 (.20)]

30 (1.18)

54 (2.13)

17 (.66)

■CONNECTION DIAGRAM

V (–)

U (+)

SLD

OUTPUT 0

In order to improve EMC performance, bond the FG

terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

7V0

2COM0

COM1

OUTPUT 1

COM2

OUTPUT 2

COM3

OUTPUT 3

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 5 / 9

COMMUNICATION CABLE CONNECTIONS

Master Unit

SLD

Remote Unit

SLD

Remote Unit

TERMINATOR TERMINATO

blue

white

yellow

Be sure to connect the terminating resistor across DA and DB at both ends of communication line.

When this unit is located at an end, turn the terminating resistor SW ON.

The Master Unit can be located at not only both ends but also any node of the of communication line.

MASTER CONNECTION

SLD

DATA ALLOCATION

Unused

RWrn+0

Analog output 0

Analog output 1

Analog output 2

Analog output 3

RWwn+0

Interval-timed Response (X) Refresh Data (Y)

ANALOG OUTPUT

I/O DATA DESCRIPTIONS

16-bit binary data

Negative values represented in 2’s complements

■ ANALOG OUTPUT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd, Nichifu Co., Ltd

6 (.24) max

3.3 (.13) max

mm (inch)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 6 / 9

CONFORMITY WITH CE MARKING

■CE MARKING

CE marking requires to integrate safety regulations existed in each country in EU territory and to secure smooth distribution

of products of which safety is guaranteed. It is mandatory by law that products distributed and sold in EU territory to have

CE mark which shows that the product conforms with the requirements of EU Directive. Each EU Directive describes the

scope of apparatuses to which that EU Directive is applied. M-System’s R7C must conform with EMC Directive.

Each Directive states only basic requirements. In order to mark the CE on an assembled machinery equipment, its manufac-

turer needs to check the overall conformity with Directives applicable to it.

■WARNINGS AND CAUTIONS WHEN INSTALLING THE R7C

The R7C needs to be installed in a control panel. This is effective not only to ensure general safety but also to contain noise

emissions by the R7C inside the control panel. We conduct a series of testing to see that the product conforms to EMC Direc-

tive while it is installed in the control panel.

Warning and cautions when installing R7C are stated below.

• Use control panels with an internal panel plate, both made of metal, when installing the R7C.

• Make sure to adequately ground the control panel and the internal panel plate with a thick cable to maintain low imped-

ance at high frequency.

• Use shielded cables for the signals taken out of the control panel.

• Choose a thick and short cable to ground the FG terminal of the R7C module to the internal panel plate of the control panel.

Note: If electromagnetic radiation disturbance increases by grounding the FG terminal, remove the grounding.

• When painting the internal plate of the control panel, apply masking to expose metal surface to secure conductivity at the

sections where the following parts are attached:

- Bolts attaching the internal panel to the control panel

- Ground for the FG of the R7C module

- Earth clamp on the shielded cable

• Noise emissions inside the control panel might leak through its openings. Design them as small as possible. Recommended

diameter is 10 cm or less.

Supplement:

Additional measures may be taken depending upon actual installation sites. These points of cautions are illustrated in the

next page.

• Prevent noise leakage by wrapping cables using shield covers, shield tubes and ﬂexible conduits etc. if noise leaks through

the cable outlet.

• Use an electromagnetic shield gasket and block up the gap between the control panel cabinet and its cover, if noise leaks

through it.

• Connecting the internal panel plate and the cover of the control panel to the main cabinet using an earth strap may be

effective to strengthen the grounding.

• Electromagnetically shielded control panel cabinet is effective for shielding.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 7 / 9

Use (e.g.) a shield cover

when noise leaks through

the opening.

To external apparatus

Keep the opening

for cabling as small as

possible.

Install an electromagnetically

shielded gasket when

noise leaks through

the opening. Shielding is strengthened

by using an electro-

magnetically shielded

control panel.

By connecting the

internal panel plate

and the panel cover with

an earth strap, grounding

may be strengthened and

EMC may be improved.

Ground the control panel

at low impedance using

(e.g.) braided wires.

Keep the opening for

ventilation as small as

posible.

Attach an electro-

magnetically shielded

filter when noise leaks

through the opening.

Install the R7C Series inside

a control panel.

Attachment part of earth

clamp should be fixed with

screw in conduction with the

internal panel plate.

• Points of cautions applicable when installing the R7C Series

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 8 / 9

■WARNINGS AND CAUTIONS WHEN LAYING CABLES

Signal cables connected to the R7C contain high-frequency components. Since these cables has the same effect as an antenna,

they emit these high-frequency components to the external space as noise or overlaps noise from the external space on them-

selves.

Cables with shielding should be used for the signal line due to the above reason.

EMC conformance test is conducted in the condition that shielded cables and earth clamps are used with the R7C.

Warning and cautions when laying cables are stated below. These points of cautions are illustrated in the next page.

• Use shielded cables for those signal cables installed out of the control panel and for thermocouple and RTD extension wires.

• All the network cables connected to R7C should be shielded.

• Use exclusively designed cables for the CC-Link.

• Expose the shield at a part of the cable cover, clip it with an earth clamp, and ground it to the internal panel of the control

panel. A drain wire connected to the panel in a pig-tail form cannot maintain low impedance against high-frequency noise,

thus grounding (noise shielding) in this form will not be effective.

Supplement:

Additional measures may be taken depending upon actual installation sites. These points of cautions are illustrated in the

next page.

• Keep cables as short as possible. It prevents noise emissions from the cables and noise overlapping to the cables.

• Attach a ferrite core to reduce noise impact to the signal cables susceptible to the noise. Ferrite core can be attached close

to the cable outlet of the control panel or close to the I/O terminal or connector, whichever is more effective. Also, the impact

might be reduced by winding the cable around the ferrite core for extra turns or attaching multiple ferrite cores.

• Keep cables which are easily affected by noise away from those which can be a noise source.

Motor Drive

Cable

Power Supply

Cable

DC Signal Cable

Network Cable

Analog Signal

Cable

Often being a noise source Often subject to noise interference.

In the following are examples of effective ways to lay cables separately:

• Keeping physical distance (farther than 20 cm from motor drive cables, farther than 10 cm for other groups).

• Dividing off by a grounded metal plate

• Grouping into separate grounded metal pipes or cable shields.

Wires on each side of a ﬁlter should not be too close to each other. Noise could ride onto the other side of cable.

Extra attention needs to be paid at the following parts.

• Noise ﬁlter that is enclosed in power cables.

• Ferrite core that is attached to signal cables.

• Noise limiting circuit (surge quenching circuit, transient absorber circuit, etc.) that is enclosed in signal cables.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7C-YV4

EM-7801-AD P. 9 / 9

Noise

Filter

Motor

Drive Cable Maintain distance between

cables and noise sources.

Grounding in pig tail form

is not effective.

• Points of cautions applicable when wiring the R7C Series

To external apparatus

Keep the cable as

short as possible.

To external apparatus

Shielded

Cable

Earth

Clamp

Remove a part of the shielded

cable cover and ground it

to the internal panel

plate using an earth

clamp.

To connect with

apparatuses outside

the control panel via

CC-Link, ground the

cable shield using

an earth clamp.

Keep the wires away from

each other at both ends of

the filter.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R7D-YV2 Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system R3-PC16A Bedienungsanleitung

M-system

M-system 6BSN Bedienungsanleitung

M-system

M-system R7E-PA8-R Bedienungsanleitung

M-system

M-system R7M-CT4E-R Bedienungsanleitung

M-system

M-system R7C-DC8C Bedienungsanleitung

M-system

M-system R3-SV4A Bedienungsanleitung

M-system

M-system R7M-DC8C Bedienungsanleitung

M-system

M-system Remote I/O R8 Series Bedienungsanleitung

M-system

M-system R3-SV8 Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DC16B-H Bedienungsanleitung

M-system

M-system M6 Series Bedienungsanleitung

M-system

M-system R7M-MS4-R Bedienungsanleitung

M-system

M-system R7D-YV2A Bedienungsanleitung

M-system

M-system R7E-MS4 Bedienungsanleitung

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system R7F4DD-DC16B-C Bedienungsanleitung

M-system

M-system R8-CT4E Bedienungsanleitung

M-system

M-system R7D-PA8 Bedienungsanleitung

M-system

M-system R7D-YS2/UL Bedienungsanleitung

M-system

M-system R7D-CT4E Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7C-DA16 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung