M-system R8-YS2 Bedienungsanleitung

R8-YS2

P. 1 / 4EM-9745 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

DC CURRENT OUTPUT MODULE

(2 points, isolated) MODEL R8-YS2

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

DC current output module.......................................... (1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•Theequipmentmustbemountedinsideapanel.

•Theactualinstallationenvironmentssuchaspanelcon-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■GENERAL PRECAUTIONS

•Beforeyouremoveormounttheunit,turnoffthepower

supply and output signal for safety.

•Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ ENVIRONMENT

•Indooruse

•Whenheavydustormetalparticlesarepresentintheair,

install the unit inside proper housing with sufﬁcient ven-

tilation.

•Donotinstalltheunitwhereitissubjectedtocontinuous

vibration. Do not apply physical impact to the unit.

•Environmentaltemperaturemustbewithin-10to+55°C

(14to131°F)withrelativehumiditywithin30to90%RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•Theunitisdesignedtofunctionassoonaspowerissup-

plied,however,awarmupfor10minutesisrequiredfor

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R8-YS2

P. 2 / 4EM-9745 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

Groove

Hook

When removing the cover, pull it out while squeezing the hooks inward.

■HOW TO UNMOUNT THE MODULE ON DIN RAIL

• Removing an intermediate module

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal

communication bus connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

Release the locking clamps and pull out straight the module.

R8-YS2

P. 3 / 4EM-9745 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

COMPONENT IDENTIFICATION

• Range

Same range for all channels. Use PC Conﬁgurator to set

independent ranges per channel.

OUTPUT RANGE SW2-1

0−20mADC OFF

4−20mADC(*) ON

• Output at The Loss of Communication

Same output for all channels.

OUTPUT AT THE LOSS OF COMMUNICATION SW2-5

OutputHold(*)

(last data correctly rerceived is hold) OFF

Stop output ON

[Note]ForStopoutput,outputxedat-5%,0mAmin.when

conﬁguration mode is DIP switch setting.

Output ﬁxed at scaling value at the loss of communication

when conﬁguration mode is PC.

• Terminator DIP SW

TERMINATOR SW SW2-6

Without(*) OFF

With ON

• Conguration Mode

CONFIGURATION MODE SW2-8

DIPswitchsetting(*) OFF

PC Conﬁgurator and communication ON

[Note]BesuretosetunusedSW2-2through2-4and2-7to

OFF.

■PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgu-

ratorSoftware(model:R8CFG):

•Outputsettingbychannels(range,scaling,zero/gainad-

justments,scalingvalueatpoweron,slalingvalueatthe

loss of communication)

•Commonsetting(lossofinternalbuscommunicationde-

tection time)

TurnSW2-8ONtoallowprogrammingbythePCCongu-

ratorviathePower/NetworkModule.

RefertotheusersmanualfortheR8CFGfordetailedopera-

tion of the software program.

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF Stopping

GreenON Valid host communication

GreenBlinking

Reading/writingconguration

RedON Setting error

RedBlinking Parameter error

Output

Status

OFF Output data in the range

RedBlinking Output data out of range

■OUTPUT CONNECTOR ASSIGNMENT

PIN ID FUNCTION

No.

1 + Output (+)

2 NC No connection

3 NC No connection

4 − Output (−)

■OPERATING MODE

(*)Factorysetting

• Module Address

The SW1-1, SW1-2, SW1-3, SW1-4 determines the tenth

placedigit,whiletheSW1-5,SW1-6,SW1-7,SW1-8doesthe

ones place digit of the address.

Addressisselectedbetween0to31.

(Factorysetting:0)

MODULE ADDRESS

SW1

×10 1234

×1 5 6 7 8

0 OFF OFF OFF OFF

1OFF OFF OFF ON

2 OFF OFF ON OFF

3OFF OFF ON ON

4OFF ON OFF OFF

5 OFF ON OFF ON

6 OFF ON ON OFF

7 OFF ON ON ON

8ON OFF OFF OFF

9ON OFF OFF ON

AO_I2

AO_I1

SW1 SW2

RUN

Status Indicator LED

Output Status Indicator LED

Internal Bus Connector

Output Connector 1

Output Connector 2

Function Setting

DIP SW

■ FRONT VIEW ■ SIDE VIEW

R8-YS2

P. 4 / 4EM-9745 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

EXTERNAL DIMENSIONS unit: mm (inch)

CONNECTION DIAGRAM

115 (4.53)

DIN RAIL

(35 mm wide)

[3 (.12)] [4 (.16)]

24 (.94) 59 (2.32)

55 (2.17)

6 (.24) 7 (.28)6 (.24)7 (.28)

OUTPUT 1

OUTPUT 2

OUTPUT CONNECTOR 1

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY OUTPUT CONNECTOR 2

BUS CONNECTOR

WIRING INSTRUCTIONS

■ e-CON connector

PWBconnectorXN2D-1474-S002(Omron)

RecommendedcableconnectorXN2A-1470(Omron)*1

Applicablewiresize:0.08mm2(AWG28)-0.5mm2(AWG20)

Outersheathdiameter:max.1.5dia

*1.The cable connector is not included in the package.

  Refertothespecicationsoftheproduct.

Andere M-system E/A-System Handbücher

M-system

M-system R7D-YV2A Bedienungsanleitung

M-system

M-system R1M Series Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DC16B-H Bedienungsanleitung

M-system

M-system R7F4DC-DA16B-C Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

M-system

M-system R7M-MS4-R Bedienungsanleitung

M-system

M-system R7F4HC-DA32-K Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system R7ML-YS2-R Bedienungsanleitung

M-system

M-system R3-SS16N Bedienungsanleitung

M-system

M-system R7ML-LC2-R Bedienungsanleitung

M-system

M-system R8-DCM16ALZ Bedienungsanleitung

M-system

M-system R7L-DC16B Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system R7G4FML3-6-DA16 Bedienungsanleitung

M-system

M-system R7L-RS4-R Bedienungsanleitung

M-system

M-system R7F4DC-DA16A-H Bedienungsanleitung

M-system

M-system R7M-EA8/UL Bedienungsanleitung

M-system

M-system R7ML-DC16A-R Bedienungsanleitung

M-system

M-system R3-DA8C Bedienungsanleitung

M-system

M-system R8-PA4 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R30NE1 Bedienungsanleitung

M-system

M-system R8-SS4N Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung