M-system 15TS Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner (body + 2 CJC sensors) ........................(1)

Mounting screw (M3.5 × 10)...............................................(2)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 50mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Be sure to put the terminal cover on while the power is

supplied.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Output ch.1

Output ch.2 Zero Adj.

Body

Specifications

Connection Diagram

(side)

Output ch.1

Span Adj. Output ch.2

Terminal Cover

INSTALLATION

Use Standard Rack (model: 15BX).

THERMOCOUPLE TRANSMITTER MODEL 15TS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-0612 Rev.6 P. 1 / 3

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

3 (.12)

51 (2.01)

82 (3.23)

2–4.3 (.17) dia.

MTG HOLE

TERMINAL COVER

7–M3.5 SCREW

8 (.31)

91 (3.58)

99 (3.90 )

25 (.98)

■CONNECTION DIAGRAM

CONNECTOR

POWER

Ch.1 OUTPUT

Ch.2 OUTPUT

–

Ch.1 T/C

CJC

SENSOR

metal leg

comp. leadwire

–

model: CJM

–

Ch.2 T/C

CJC

SENSOR

metal leg

comp. leadwire

–

■TERMINAL ASSIGNMENT

CJC SENSOR

(model: CJM)

15TS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-0612 Rev.6 P. 2 / 3

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage supplied to the rack

(model: 15BX). For the DC power source, be sure that the

ripple level is within 10% p-p.

3) Input: Check that the input voltage is within 0 – 100% of

full-scale.

If the thermocouple or its extension wires are broken, the

output goes over 100% (below 0% with downscale) due to

burnout function. Check leadwires in such a case.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

Use extender card (model: 10EC) for SPAN adjustment.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

5) Go through the same procedure for the Ch. 2 Output.

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

15TS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-0612 Rev.6 P. 3 / 3

Andere M-system Sender Handbücher

M-system

M-system Mini-M M2VS Bedienungsanleitung

M-system

M-system Mini-M M2VF2 Bedienungsanleitung

M-system

M-system 27U Bedienungsanleitung

M-system

M-system Mini-M M2WVS Bedienungsanleitung

M-system

M-system M3LU2 Bedienungsanleitung

M-system

M-system LINEARIZER JFX Bedienungsanleitung

M-system

M-system 6M Bedienungsanleitung

M-system

M-system Mini-M M2AMS Bedienungsanleitung

M-system

M-system B5MS Bedienungsanleitung

M-system

M-system Mini-M M2MS Bedienungsanleitung

M-system

M-system FJR Bedienungsanleitung

M-system

M-system W5-UNIT Bedienungsanleitung

M-system

M-system M5VF Bedienungsanleitung

M-system

M-system W5MS Bedienungsanleitung

M-system

M-system 6BLC Bedienungsanleitung

M-system

M-system VOS2T Bedienungsanleitung

M-system

M-system CTH Bedienungsanleitung

M-system

M-system WRS2 Bedienungsanleitung

M-system

M-system F2VF Bedienungsanleitung

M-system

M-system MXV Bedienungsanleitung

M-system

M-system 10TG Bedienungsanleitung

M-system

M-system M5VF2 Bedienungsanleitung

M-system

M-system Mini-M M2LCS Bedienungsanleitung

M-system

M-system SENTRONIC M2SES Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung