Magnit RMV-1931 Bedienungsanleitung

Electric vacuum cleaner/Пылесос электрическийInstruction manual Инструкция по эксплуатацииRMV-1931/

RUSEN

DEAR CUSTOMER!We congratulate you on purchasing home appliance of “MAGNIT” trademark. We are sure that this unit will correspond to the highest requests for the quality and will become the real reliable support in your home cares. Before starting using this appliance, please carefully read the instruction manual and follow the rules of using. In this case the trademark “MAGNIT” will assure the long life of the equipment you have bought.Thank you for choosing us!3

DESCRIPTION1. Handle2. Stainless steel telescopic tube3. Hose4. Switch Pedal5. Air outlet grid6. Metal floor brush7. Cyclone dust barrelAccessories:1. Flat nozzle 2. Combination brush1234567

4SAFETY WARNING1. Be sure to use the cleaner in compliance with the contents of this manual,and use the fittings designated by the manufacturer.2. Please do not leave the cleaner when it is powered on. Turn off the powerswitch and pull out the power plug when not using or before maintenance.3. Please do not pull or carry the cleaner by the power cord, or nip it whenclosing a door; keep the cord free from the press of the cleaner.4. Please do not let children take the cleaner as a toy, and close attention isnecessary when the cleaner approaches children.5. Please do not use the cleaner when its power cord or plug is damaged.Send it to the appointed service center. Please do not unplug by pulling thecord or plug. To unplug, grasp the plug, not the cord.6. Never pull the power plug or use the cleaner with wet hands.7. When using the cleaner, pay attention to prevent any hair roll or otherrubbish block up the air inlet (including the hose and the spile), otherwisemotor failure and housing distortion may be caused. If the mattersabsorbed in forms a blockage, stop the cleaner by pulling out the powerplug immediately to clean the blockage.8. When using the cleaner, don’t plug up the air outlet by towel or othermatters, otherwise the efficiency of dust absorbance will be influenced,and the motor will be at high risk of being burnt out.9. Never use the cleaner at uneven floor or ground; and be very careful whencleaning stairs to prevent the cleaner from falling down.10.Never absorb live stumps with the cleaner, otherwise the motor may bedamaged.11.The cleaner should be kept far away from heat sources (such as centralheating, oven, etc) to avoid the distortion of plastic parts as well as theinfluence caused by such distortion.12. Before using the cleaner, please remove big and sharp matters on the floorto avoid damaging the plastic parts, filter gauzes and motor.13. Never absorb water or other liquid with this cleaner, otherwise, the motorwill be damaged.

5ASSEMBLY INSTRUCTIONS1. Before assembling the vacuum cleaner, please confirm all parts andcomponents for the cleaner are received by referring to Parts and ComponentsList.2. Please remember to cut off the power supply before assembly.Assembly of hose1. As it is shown in Figure (3), insert the hose into the duct inlet of themachine body in horizontal direction. Please pay attention to the alignmentof two projecting parts. Turn the hose right when it is pushed into thebottom, a click of inserting sound may be heard, i.e. the hose is assembledinto the machine body completely.Figure (3)2. Assembly and Removal of dust barrelAs it is shown in Figure (4), place the bottom of the dust barrel on theprojecting part at the front end of the machine body, and press down the dustbarrel. When the front-end hook is entered into the corresponding part of themachine body completely, and a click of inserting sound is heard, whichindicate that the dust barrel is assembled in place. To remove the dust barrel,press down the handle of the dust barrel; when the handle is pressed down tothe bottom, the dust barrel can be lifted to remove.Figure (4)

6ASSEMBLY OF ACCESSORIES1. Figure (5) is the accessory bracket. Get the flat nozzle and the combinationbrush stuck in the corresponding clips according to the accessoryinstallation indication shown on the accessory bracket.Figure (5)ASSEMBLY OF STAINLESS STEEL TELESCOPIC TUBE AND FLOOR BRUSHInsert the front end of the hose handle into the telescopic tube according toFigure (6); then insert the other end of the telescopic tube into the roundedinlet of the floor brush, and adjust to the proper direction. At this time, theassembly of the whole machine is completed.Figure (6)

7OPERATION INSTRUCTIONSHow to start1. First of all, pull out the power cord from the cord reel to the neededlength; insert the power cord plug into the power socket, and press downthe power switch button with finger or step on it with foot; then you cancontrol the start and stop of the cleaner.2. The yellow mark on the power cord indicates its desired length. Neverpull out the power cord to the length exceeding the red mark.CONTROL OF SUCTION FORCEWhen the suction inlet is jammed by some cloth due to the over-large suctionforce, you can adjust the air escape pushbutton on the hose handle to controlOperation Instructionsthe suction force at the suction inlet, as is shown in Figure (7).PROTECTIVE DEVICES OF MOTOR1. There is a temperature controller designed in the body of cleaner motor,which can automatically cut off the power supply of motor to preventoverheating. When the air-inlet or air-outlet pipe is overloaded or blocked, thetemperature of motor rises, then the temperature controller cuts off the powersupply of motor automatically to make the motor cool, preventing the cleanerfrom being damaged.2. If the temperature controller is cut off, stop the cleaner immediately andpull out the power plug to make the cleaner cool, and check and remove thehair roll or other roll-like rubbish blocking the air inlet (including the hoseand the spile), and replace the filter HEPA or filter gauze when necessary.3. After cooling the motor for 30mins, plug in the power plug and checkwhether the temperature controller has been reset. If the power supply of thecleaner hasn’t been cut off, the temperature controller of the motor won’t bereset even when the motor has become cool.Figure (7)

8MAINTENANCE OF THE CLEANER1. All the day-to-day maintenance and repair jobs should be done after thepower plug has been pulled out.2. Frequently remove the rubbish from the dust barrel, so as to avoid thefailure of the cleaner.3. Never wipe the surface of the cleaner with gasoline or oily liquid. Wipe itwith water or neutral detergent. Caution: be sure to wring out the wiping clothdry for wiping, it is prohibited for water to infiltrate into electrical elements ofthe cleaner.4. When the cleaner is placed idle not in use, it should not be put directlyunder the sun or in a damp place.STORAGE OF THE CLEANER1. Upon the completion of the operation of the cleaner, turn off its powersupply, and pull the power plug out of the power socket, then step on thecord reeling button to reel in the power cord fully. Hang the floor brush ontothe floor brush hook, as is shown in Figure (8).Figure (8)2. Place the cleaner in the dry indoor environment.

9Remove the rubbish in the dust barrel frequently to avoid the failure of thecleaner.1. Clean the dust barrel only after the power plug of the cleaner has beenpulled out;2. Put the dust barrel over the rubbish bin (bag), press down the releasingbutton of the dust barrel, the bottom cover of the dust barrel willautomatically fall down, and clear and empty the dust barrel, as is shownin Figure (9).CLEANING OF THE DUST BARRELCleaning of front filter for motor:Warning: please make sure the power supply of the cleaner has been cut offbefore carrying out the following steps:1. Pull out the power cord plug of the cleaner from the power socket.2. Press down the handle of the dust barrel to remove the dust barrel, andremove the cover of the front filter for motor, and then use the brush toCleaning of the Dust BarrelFigure (8)clean the filter (sponge and filter gauze with composite coating) or place itunder the cock to clean, as is shown in Figure (10).Figure (9)Figure (10)

The life-time of the product is 2 years.You can find full information about the appliances of “MAGNIT” trademark on www.magnit.net

10Caution:It is normal that the white central filter in the dust barrel may change color,which cannot affect its filtration performance. If the hose and the central filterare difficult to clean, we recommend that you use water to flush them;however, please be sure to place them in the dry air for at least 24 hours afterthey are flushed by water.Key Points:Please note: when the dust collecting barrel or the filter cover is not installedin place, the operation status will be invalid, and the cleaner will have no dustabsorption capacity. At this time, you need to check carefully whether the dustcollecting barrel and the filter cover have been installed in place.Caution: please keep the suction passage unobstructed, otherwise the motormay become overheating or even be damaged.REPLACEMENT OF REAR FILTER FOR MOTORThe rear filter for motor is installed behind the air outlet grid, which cannot bewashed due to the materials used. When the surface is jammed seriously bydust, the filter should be replaced by a new one to maintain enough suctionforce. (Figure 11)Figure 11It is usually necessary to clean and replace the filters for motor onlyafter they have been used for 6 months to 12 months. Pleaseremember to confirm that all filters have been correctly installedinto the machine before turning on the cleaner to use.Key Points:The power supply of the cleaner must be cut off before replacing any filter!Faults and repairIn case of abnormality with this product, please treat it in the way as statedhereinafter; if the cleaner still refuses to work normally, please contact thestop from where this product was bought or with the appointed service point.