Malvern Instruments Mastersizer X Bedienungsanleitung

QS Small Volume Sample

Dispersion Unit

QS Small Volume Sample

Dispersion Unit

MAN 0161 Issue1.1 April 1997

©Malvern Instruments Ltd. 1995, 1997

Malvern Instruments makes every effort to ensure that this document is correct. However, due to

Malvern Instruments policy of continual product development we are unable to guarantee the accuracy

of this, or any other document after the date of publication. We therefore disclaim all liability for any

changes, errors or omissions after the date of publication.

No reproduction or transmission of any part of this publication is allowed without the express written

permission of Malvern Instruments Ltd.

Head Office:

Malvern Instruments Ltd.

Spring Lane South,

Malvern.

Worcestershire.

WR14 1XZ U.K.

Tel + [44] (0) 1684-892456

Fax + [44] (0) 1684-892789

Printed in England

Contents

Chapter 1 - Introduction to this manual

Access to the Accessory 1.1

Malvern personnel 1.1

Supervisor 1.1

Operator 1.1

Systems covered by this manual 1.1

Assumed information 1.2

Windows terms 1.2

Menu Commands 1.2

Where to find information 1.3

Other reading 1.5

Chpater 2 - Health & safety

Introduction 2.1

Site requirements 2.1

Laser safety 2.2

General laser safety 2.2

Laser Warnings 2.2

Electrical safety warnings 2.3

Sample handling 2.3

Moving the Accessory 2.5

Repackaging the Accessory 2.5

Disposing of the Accessory 2.6

Chapter 3 - Installation

Introduction 3.1

Site requirements 3.1

CONTENTS

QS SMALL VOLUME SAMPLE DISPERSION UNIT

Page i

Unpacking the Accessory 3.2

Checking the contents 3.3

Connecting up your Accessory 3.4

Mastersizer S and X 3.4

Mastersizer Micro and Microplus 3.6

Power up the Accessory 3.8

Installation check 3.9

Chapter 4 - Getting to know your Dispersion Unit

Introduction 4.1

Features of the Accessory 4.1

Controller Unit rear panel 4.3

The Malvern software 4.4

Qspec MS1 macro 4.4

Chapter 5 - How the Accessory works

Introduction 5.1

What does the Accessory do? 5.1

How does the Accessory do it? 5.1

Operating principle 5.1

How to make a measurement using the Accessory 5.2

Chapter 6 - Making a measurement using the Accessory

Introduction 6.1

System and Accessory preparation 6.1

Making a measurement 6.1

CONTENTS

QS Small Volume Sample Dispersion Unit

Page ii

MAN 0161

Chapter 7 - Creating and changing SOP’s

Creating a new SOP 7.1

Editing and deleting a SOP 7.5

Chapter 8 - Sample preparation

Introduction 8.1

Trapped air/bubbles 8.1

Using a slurry 8.2

The use of ultrasonics 8.2

Chapter 9 - Maintenance

Introduction 9.1

Replacing the sample tubing 9.1

Replacing the fuse 9.2

Cleaning the Accessory 9.2

Disassembly 9.3

Cleaning 9.4

‘O’ ring seals 9.4

Reassembly 9.4

Cleaning the cell windows 9.5

Appendix A - Specification

Introduction A.1

Appendix B - Chemical compatability

Introduction B.1

Components in contact with

sample and dispersant B.1

CONTENTS

QS SMALL VOLUME SAMPLE DISPERSION UNIT

Page iii

Appendix C - Simple fault finding

Introduction C.1

Fault diagnosis and correction C.1

Appendix D - Installing the Qspec MS1 macro

Introduction D.1

Appendix E - Statement of EMC performance

Statement of EMC performance E.1

CONTENTS

QS Small Volume Sample Dispersion Unit

Page iv

MAN 0161

CHAPTER1

Introduction to this manual

Access to the Accessory

Within this manual reference is made to the various people that will have access to

the Accessory. Below is a list of these people and their responsibility:

Malvern personnel

Malvern personnel (service engineers, representatives etc.) have full access

to the Accessory and are authorised to perform all service procedures that

may be required.

Supervisor

The supervisor is the person responsible for the management/safety of the

System and of its operation. The supervisor is responsible for the training

of the operators. The supervisor can perform all user maintenance routines

identified in chapter 9, including changing the fuses.

Operator

An operator is a person trained in the use of the system. The operator can

perform all user maintenance routines identified in chapter 9, except

changing the fuses.

Systems covered by this manual

This manual covers the installation, operation and maintenance for the QS Small

Volume Sample Dispersion Unit. This accessory is used in association with

various Mastersizer optical units.

Mastersizer is a generic name given to a family of systems. Each system within the

family uses the same principles of operation and only vary in operation in small

areas. For this reason the manual has been written to cover more than one

instrument.

CHAPTER 1

QS SMALL VOLUME SAMPLE DISPERSION UNIT

Page 1.1

This manual covers the Accessory in association with the following Mastersizer

family members:

Instrument. Ref. Number.

Mastersizer X standard bench. MAM 5000

Mastersizer X long bench. MAM 5002

Mastersizer S standard bench. MAM 5004

Mastersizer S long bench. MAM 5005

Mastersizer Micro. MAF 5000

Mastersizer Microplus. MAF 5001

Assumed information

For clarity this manual will assume that you are using your Accessory in

association with a standard bench Mastersizer S. If there are any operational

procedures that differ when in use with another Mastersizer family member, the

alternative information will be given.

Within this manual the QS Small Volume Sample Dispersion Unit will be

referred to as the “Small Volume Sample Dispersion Unit”, or as the “Accessory”.

Throughout this manual the Small Volume Sample Dispersion Unit refers to the

Dispersion Unit & the Controller Unit.

Within this manual the Mastersizer system will be referred to as the “Mastersizer”

or the “system” unless the information given is for a particular instrument.

Windows terms

It is important that you understand some windows terms before reading further.

Refer to chapter 1 of the Getting Started manual.

Menu Commands

Menu commands from the Malvern software are referred to in the form main

menu-menu item. As an example, the command Setup-Hardware refers to

selecting the Hardware item in the Setup menu. The same rules apply for

sub-menus of sub-menus. Menu commands are always shown in bold text.

CHAPTER 1

QS Small Volume Sample Dispersion Unit

Page 1.2

MAN 0161

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Malvern Instruments Laborausrüstung Handbücher

Malvern Instruments

Malvern Instruments Zetasizer uV Bedienungsanleitung

Malvern Instruments

Malvern Instruments DEG0003 Bedienungsanleitung

Malvern Instruments

Malvern Instruments ZETASIZER Benutzerhandbuch

Malvern Instruments

Malvern Instruments Zetasizer uV Bedienungsanleitung

Malvern Instruments

Malvern Instruments Zetasizer Nano Bedienungsanleitung

Malvern Instruments

Malvern Instruments Spraytec Bedienungsanleitung

Malvern Instruments

Malvern Instruments Zetasizer Series Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung