Mandik SEDM-L Bedienungsanleitung

These technical conditions stipulate a number of manufactured sizes, main dimensions, design and range of use of

multi-slat smoke and heat extraction dampers - multi SEDM-L (hereinafter only dampers). They're binding for production,

design, ordering, delivery, storage, assembly, operation, maintenance and serviceability checks.

1. Description.........................................................................................................................

2. Design................................................................................................................................

3. Communication and control devices....................................................................................

4. Dimensions, weights and effective area..............................................................................

5. Placement and Assembly....................................................................................................

6. Statement of installations....................................................................................................

7. Suspension system……………......................................................................................….

8. Pressure loss......................................................................................................................

9. Coefficient of local pressure loss.........................................................................................

10. Noise data.........................................................................................................................

11. Material.............................................................................................................................

12. Inspection.........................................................................................................................

13. Testing..............................................................................................................................

14. Logistic terms....................................................................................................................

15. Warranty...........................................................................................................................

16. Assembly..........................................................................................................................

17. Entry into service and revisions.........................................................................................

18. Spare parts.......................................................................................................................

19. Ordering key.....................................................................................................................

20. Data label...........................................................................................….......……........….

Smoke and heat extraction dampers - multi are closures in the ductwork of smoke extraction

devices. In the event of a fire, the smoke and heat removal system open the dampers in the

affected section, therefore enabling the extraction fans to remove combustion products and heat

from the endangered areas.

The damper slat is controlled by an actuator.

The damper is fire resistant and is designed for systems with automatic or manual activation.

Smoke dampers are intended for use in spaces with multiple fire compartments, which can be

connected by a smoke extraction duct tested according to EN 1366-8 or can be installed in the

construction of the fire compartment.

The dampers can be supplied with flange(s) or without flange(s), with cover grille(s).

Flanges and grilles are not installed on the damper, they are included loosen. Flanges are

required to fit the cover grilles. Grills and flanges must be installed to the dampers only after

installation of the damper into the wall.

In normal operation, the SEDM-L dampers remain closed. If necessary, in the event of a fire, the

SEDM-L dampers in the affected fire section will open completely so that the smoke can be

removed. When the smoke and heat removal dampers are activated, the dampers used for air

supply in the affected section open. The dampers used to supply air in the affected fire section

are installed at the ground. The dampers are controlled from the central control system on the

basis of signals, e.g. from smoke detectors. The use of cables with a certain fire resistance for the

supply voltage ensures that the actuator is supplied even in the event of a fire.

During ventilation, SEDM-L dampers in the smoke and heat extraction system are controlled by

a control system, it's possible to fully open, close or continuously control the flow. The SEDM-L

dampers, which are used for air supply, remain closed during ventilation.

Position:

1 SEDM-L

2 Ventilation grille or damper for smoke and heat removal from one section

Air inlet

4 Smoke barrier

5 Fan for forced smoke and heat removal

6 Duct for smoke extraction from one section

7 Multi-section smoke extraction duct

The damper's faultless operation is ensured under the following conditions:

a) maximum air flow speed 12 m/s

b) maximum vacuum up to 1000 Pa or overpressure up to 500 Pa

The dampers are suitable for installing in a vertical position, with the slat axis horizontal.

The dampers are designed for environments protected against weather conditions with class 3K5

climatic conditions, without condensation, icing, ice formation, without water and from sources

other than rain and with a temperature limit of -30°C to 50°C.

• CE certification according to EN 12101-8

• tested according to EN 1366-10

• classified according to EN 13501-4 + A1

• fire resistance according Tab. 1.3.1

• pressure class 2 (vacuum 1000 Pa / overpressure 500 Pa)

• tightness according to EN 1751 via body class C and via damper slat min. class 3

• Cmod cycling according to EN 12101-8

• Certificate of Constancy of Properties No. 1391-CPR-2021/0009

• Performance declaration No. PM/SEDM-L/01/22/1

• Hygienic assessment of fire dampers - Report No. 1.6/pos/21/19b

In a solid wall construction and on duct in a solid wall

construction, th. 100 mm

For duct in a solid wall construction, th. 100 mm

In gypsum wall construction and on the duct in gypsum

wall construction, th. 100 mm

Belimo actuators are used for dampers, series BEN, BEE, BE for 230V AC resp. 24 V AC/DC.

After connection to the power supply voltage, the actuator moves the damper slats to the "OPEN" position

or "CLOSED" (according to the corresponding connection, see wiring diagram). If the power supply is

interrupted, the actuator stops at the current position. The signalling of the "OPEN" and "CLOSED" damper

slats positions is ensured by two built-in fixed “potential-free” end- limit switches.

The actuator for operating the damper slats is mounted in an insulated cover/box. It is accessible

after removing the cover lid. The electrical connection of the actuator is made with a non-flammable cable

(or a cable located in the adjoining cable duct), which passes through an opening made in the wall of the

insulated cover/box when installing the damper or when connecting the actuator power cable. The cable

entry must meet a minimum fire resistance of 30 minutes.

Position:

1 Damper housing

2 Slats

3 Silicone slat seal

4 Internal silicone seal

5 Fire-fighting foam tape

6 Slat stop

Actuator housing

Actuator housing cover

Actuator

Belimo modulating actuators, BEN (BEE)-SR series for 24V AC/DC are specially designed for remote control

of fire dampers. The position of the damper slats is adjustable by means of control voltage 0 (2)...10V DC.

The signalling of the "OPEN" and "CLOSED" damper slats positions is ensured by two built-in fixed

“potential-free” limit switches.

The actuator for operating the damper slats is mounted in an insulated cover/box. It is accessible after

removing the cover lid. The electrical connection of the actuator is made with non-flammable cables (or

cables located in the adjoining cable duct), which pass through an opening made in the wall of the insulated

cover when installing the damper or when connecting the power cables of the actuator. The cable entry must

meet a minimum fire resistance of 30 minutes.

Power voltage AC/DC 24 V

50/60Hz

AC/DC 24 V

50/60Hz

AC 230 V

50/60Hz

Power consumption - in operation

- in the end position

3 W

0,1 W

3 W

0,3 W

4 W

0,4 W

Dimensioning 6 VA (Imax 8,2 A @ 5 ms) 6,5 VA (Imax 8.2 A @ 5 ms) 7 VA (Imax 4 A @ 5 ms)

Protection class III III II

Degree of protection IP 54

Adjustment time for 95° < 30 s

Ambient temperature

Storage temperature

-30°C … +55°C

-40°C … +80°C

Connection - drive

- auxiliary switch

Cable 1 m, 3 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

(BEN 24-ST) with plug

connectors

Cable 1 m, 4 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

Cable 1 m, 3 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

S2S1 S3 S5S4 S6

<5° <80°

S2S1 S3 S5S4 S6

<5° <80°

N L1

S2S1 S3 S5S4 S6

<5° <80°

DC (0)2...10 V

DC 2...10 V

S2S1 S3 S5S4 S6

<5° <80°

S2S1 S3 S5S4 S6

<5° <80°

N L1

S2S1 S3 S5S4 S6

<5° <80°

DC (0)2...10 V

DC 2...10 V

Power voltage AC/DC 24 V

50/60Hz

AC/DC 24 V

50/60Hz

AC 230 V

50/60Hz

Power consumption - in operation

- in the end position

2,5 W

0,1 W

3 W

0,3 W

3,5 W

0,4 W

Dimensioning 5 VA (Imax 8,2 A @ 5 ms) 5,5 VA (Imax 8.2 A @ 5 ms) 6 VA (Imax 4 A @ 5 ms)

Protection class III III II

Degree of protection IP 54

Adjustment time for 95° < 60 s

Ambient temperature

Storage temperature

-30°C … +55°C

-40°C … +80°C

Connection - drive

- auxiliary switch

Cable 1 m, 3 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

(BEE 24-ST) with plug

connectors

Cable 1 m, 4 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

Cable 1 m, 3 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

S2S1 S3 S5S4 S6

<3° <87°

S2S1 S3 S5S4 S6

<3° <87°

N L1

Power voltage AC/DC 24 V

50/60Hz

AC 230 V

50/60Hz

Power consumption - in operation

- in the end position

12 W

0,5 W

8 W

0,5 W

Dimensioning 18 VA (Imax 8,2 A @ 5 ms) 15 VA (Imax 7,9 A @ 5 ms)

Protection class III II

Degree of protection IP 54

Adjustment time for 95° < 60 s

Ambient temperature

Storage temperature

-30°C … +50°C

-40°C … +80°C

Connection - drive

- auxiliary switch

Cable 1 m, 3 x 0,75 mm2

Cable 1 m, 6 x 0,75 mm2

(BE 24-ST) with plug

connectors

Position:

1 Damper housing

2 Slats

3 Silicone slat seal

4 Internal silicone seal

5 Fire-fighting foam tape

6 Slat stop

Actuator housing

Actuator housing cover

Actuator

10 Communication and power supply device BKNE 230-24

Design with communication and power supply device BKNE 230-24 and with actuator BEN (BEE, BE)-ST for 24V.

The BKNE 230-24 serves on the one hand as a decentralized network device for powering the actuator and on the other

hand transmits the signal of the communication and control device BKSE 24-6.

It simplifies electrical installation and connection of dampers. In the meantime, it facilitates “on-site inspection” and allows

central control and inspection of dampers using a simple 2-wire line.

The BKNE 230-24 transmits the "OPEN" / "CLOSED" damper position (switches in the actuator) and fault messages to

the BKSE 24-6. It also receives commands from the control device and controls the adjustment of the actuator to the

desired position. The last control command will be retained even after a temporary network failure..

The BKNE 230-24 controls the switching position of the actuator, its adjustment time and the data exchange with the

BKSE 24-6. In addition, it controls the actuator current (actuator connection) and the power supply.

To simplify the connection, the actuator is equipped with plug connectors that plug directly into the BKNE 230-24.

The actuator, communication and power supply device BKNE 230-24 are mounted in an insulated cover, they are

accessible after removing the cover. The electrical connection of the actuator and the BKNE 230-24 communication and

power supply device is made with a non-flammable cable (or a cable located in an adjoining cable duct), the two-wire

BKNE 230-24 cable should be connected to terminals 6 and 7. It is also recommended to use cable, which is used for fire

signalling network. The cables pass through an opening made in the wall of the insulated cover when installing the damper

or when connecting the actuator power cable. The cable entry must meet a minimum fire resistance of 30 minutes.

For more information on actuators and devices, see the Belimo catalogue.

Power voltage AC 230V 50/60Hz

Power consumption 10 W (including actuator)

Dimensioning 19 VA (including actuator)

Protection class II

Ambient operation temperature

Storage temperature

-30°C … +50°C

-40°C … +80°C

Connection - network

- drive

- terminal blocks

cable 1 m without plug

6-pin plug, 3-pin plug

screw terminals for 2x1.5 mm2 conductor

AC 230 V

1 to 5 should not be

connected

two-wire line to

BKSE 24-6

yellow flashing damper rotates to the open position

yellow lit-up damper is open

green flashing damper rotates to the closed position

green lit-up damper is closed

yellow or green flashes twice as often fault

yellow + green dark network outage

Andere Handbücher für SEDM-L

Inhaltsverzeichnis

Andere Mandik Feuer- und Rauchklappe Handbücher

Beliebte Feuer- und Rauchklappe Handbücher anderer Marken

HVC

HVC NCA 700 Series Bedienungsanleitung

Wildeboer

Wildeboer FR90 Bedienungsanleitung

FläktGroup

FläktGroup ETCE Programmierhandbuch

Tamco

Tamco 1000 SM Series Bedienungsanleitung

Greenheck

Greenheck Vektor-MD Bedienungsanleitung

Lindab

Lindab FBC2 Installations- und Betriebshandbuch

EKOVENT

EKOVENT EKO-SRB1 Montageanleitung

Greenheck

Greenheck HBS Series Handbuch

Advanced Air

Advanced Air 0160 Series Bedienungsanleitung

Greenheck

Greenheck CRD-1WT Bedienungsanleitung

Swegon

Swegon Actionair CSS Series Bedienungsanleitung

TAKACHIHO

TAKACHIHO FYN-M 1 Series Bedienungsanleitung

Valmet

Valmet Flowrox Expulse Series Handbuch

ETS NORD

ETS NORD NORDfire FDMB Bedienungsanleitung

AMS

AMS CR2 Bedienungsanleitung

Arzel

Arzel RegiDamper Bedienungsanleitung

mercor

mercor mcr S-THERM C Bedienungsanleitung

Greenheck

Greenheck FD Series Betriebsanleitung