Mandik SEDS-L Bedienungsanleitung

These technical specifications state a row of manufactured sizes and models of smoke extraction dampers - single

(further only dampers) SEDS-L. It is valid for production, designing, ordering, delivery, maintenance and operation.

1. Description.........................................................................................................................

2. Design................................................................................................................................

3. Dimensions, weights...........................................................................................................

4. Placement and Assembly....................................................................................................

5. Pressure drops...................................................................................................................

6. Noise data………………………………...............................................................................

7. Material............................................................................................................................. 14

8. Inspection, testing............................................................................................................. 14

9. Logistic terms....................................................................................................................

10. Assembly..........................................................................................................................

11. Entry into service and revisions.........................................................................................

12. Spare parts.......................................................................................................................

13. Product label....................................................................................................................

14. Ordering key.................................................................................................................….

Smoke extraction dampers - single are shutters in smoke exhaust piping systems. Dampers are

designed to remove heat and combustion products (e.g. smoke) from single fire compartment.

In the event of fire the Smoke and Fire ventilation system opens the damper in the affected

section which removes combustion products and heat from this section.

The damper blade is operated by an actuating mechanism.

The dampers can be installed in various duct sizes with respect to the field of direct applications

according with EN 1366-9.

The field of direct applications based on tests results is acceptable according to EN 1363-1,

part A.1 and A.2, EN 1366-2, part 13 and EN 1366-10, part 9.

Smoke extraction dampers - single are classified as

The duct can be ended by KMM (TPM 002/96) grilles.

Damper characteristics

• CE certified acc. to EN 12101-8

• Tested in accordance with EN 1366-10

• Classified acc. to EN 13501- 4+A1

• External Casing leakage min. class B, Internal leakage min. class 3 acc. to EN 1751

• Cycling test in class C 10000 acc. to EN 12101-8

• ES Certificate No. 1391-CPR-2018/0106

• Declaration of Perfomance No. PM/SEDS-L/01/20/1

• Hygienic assessment of fire dampers - Report No. 1.6/pos/19/19c

Working conditions

Dampers are designed for smoke exhaust piping systems with underpressure max. 1500 Pa or

overpressure max. 500 Pa.

Dampers are designed for maximum air velocity 12 m.s.

Dampers are installed with the horizontal or vertical axis of the blades.

Dampers are intended for installation on air ducts and in/onto the walls where in the case of wall

installation, this wall with damper does not have fire resistance and therefore does not separate

two fire compartments.

Dampers are suitable for systems without abrasive, chemical and adhesive particles.

Dampers are designed for macroclimatic areas with mild climate according to EN 60 72133.

Temperature in the place of installation is permitted to range from - 20°C to + 50°C.

Design with actuating mechanism

SEDS-L is equipped by actuating mechanism Belimo BLE24 (BE24-12) for 24V supply or

BLE230 (BE230-12) for 230V supply. After being connected to power supply the actuating

mechanism displaces the damper blade into operation position "OPEN" or „CLOSED“ (according

to method of connection, see connection diagram). Running time is max. 60s. If is power supply

cut off, actuating mechanism is stopped in actual position. The crank handle supplied with the

actuator allows it to be operated manually. Signaling of the damper blade positions "OPEN" and

"CLOSED" is provided by means of two integrated, invariably set terminal switches.

S3S2

S1 S6S5S4

<3° <87°

Parrallel connection of other driver is possible.

Pay attention to the power input data.

Nominal voltage AC 24V 50/60Hz

DC 24 V

AC 230 V 50/60Hz

Power consumption - motoring

- holding

7,5 W

< 0,5 W

< 1 W

Dimensioning 9 VA (Imax 2,7 A @ 5 ms) 12 VA (Imax 6 A @ 5 ms)

Protection class III II

Degree of protection IP 54

Running time for 95° < 30 s

Ambient temperature range

Non-operating temperature

- 30 °C … + 50 °C

- 40 °C … + 80 °C

Connecting - motor

- auxiliary switch

cable 1 m, 3 x 0,75 mm

cable 1 m, 6 x 0,75 mm

(BLE 24-ST) with plug-in connectors

S2S1 S3 S5S4 S6

BLE24-ST: Design with connector plugs for communication

Connection through

an insulation transformer.

to network and communication device BKNE230-24

Parrallel connection of other driver is possible.

Pay attention to the power input data.

<3° <87°

Nominal voltage AC 24V 50/60Hz

DC 24 V

AC 230 V 50/60Hz

Power consumption - motoring

- holding

12 W

0,5 W

Dimensioning

18 VA (Imax 8.2 A @ 5 ms)

15 VA (Imax 7.9 A @ 5 ms)

Protection class III II

Degree of protection IP 54

Running time for 95° < 60 s

Ambient temperature range

Non-operating temperature

- 30 °C … + 50 °C

- 40 °C … + 80 °C

Connecting - motor

- auxiliary switch

cable 1 m, 3 x 0,75 mm

cable 1 m, 6 x 0,75 mm

(BE 24-ST) with plug-in connectors

Design with the communication and power supply unit

Design with the communication and power supply unit BKNE230-24 and the actuating mechanism

BLE24(BE24-12)-ST.

BKNE230-24 functions as a decentralized network device for supplying the actuating mechanism

BLE24(BE24-12)-ST on one hand and on the other hand it transmits signals from communication

and control device BKSE24-6.

It simplifies electrical wiring and interconnection of dampers. It facilitates on site check and

enables central control and checks of fire damper by means of a simple 2-conductor wiring.

BKNE230-24 signals the damper position „OPEN“/„CLOSED“ (from switches on the actuator)

and any fault alarms to the BKSE24-6 unit. It also receives positioning commands from the

control unit and triggers the actuator to the required position. The last control command is

retained troughout temporary power failures.

The BKNE230-24 unit monitors the positions of the switches on the actuator, its running time and

the exchange of data with the control and monitoring unit BKSE24-6. It also monitors the actuator

current and the power supply. In order to make installation as simple as possible the smoke

extraction damper actuators ...-ST are fitted with plug connectors that can be inserted directly into

the BKNE230-24 unit.

The 2-wire conductor must be connected to screw terminals 6 and 7. It is recommended that a

fire alarm signal cable suitable for the application be used for the 2-wire conductor. It is essential

to ensure the correct polarity.

More information in catalogue Belimo.

Communication and control devices

Nominal voltage AC 230V 50/60Hz

Power consumption 10 W (including actuating mechanism)

Dimensioning 19 VA (including actuating mechanism)

Degree of protection II

Ambient temperature range

Non-operating temperature

- 30 °C … + 50 °C

- 40 °C … + 80 °C

Connecting - net

- actuator

- terminal board

cable 1 m without plug

6-pole connector, 3-pole connector

screw terminals for cable 2x1,5 mm

BKSE24-6 indicates operating status and fault signals for the smoke extraction dampers. The

auxiliary contacts that are incorporated also allow functions to be signaled or passed on to

higherlevel control systems. The signals from the BKNE230-24 unit are received by the

BKSE24-6 unit and evaluated individually. All BKNE230-24 units are triggered simultaneously.

To BKSE24-6 can be connected max. 6 BKNE230-24.

Communication is via the 2-wire conductor. Correct operation of the dampers is indicated by

means of two LEDs. The operating status of the SBSE-Control system and any faults are also

indicated by this LED and the corresponding fault LED.

The BKSE24-6 unit can be clipped directly to a 35 mm DIN mounting rail and connected by

means of two 9-pole plug-in terminals. The BKSE24-6 unit isn´t in the scope of delivery MANDIK

company.

an insulation transformer.

AC 24 V

SMOKE EXTRACTION

Connection through

a1...a6

BKNE230-24

Input 2

(isolated)

AUTO

CEASE SMOKE EXTRACTION

COM

Delay 0 s (Fan)

Delay 60 s (Fan)

OPEN

CLOSED

*Fault (Error)

*Inverted output: fault = contact open

Input 1

1 Damper body

2 Damper blade

3 Actuating mechanism cover

Dimensions

Nominal voltage AC 24 V 50/60Hz

Power consumption 3,5 W (operating position)

Dimensioning 5,5 VA 18 VA (Imax 6.4 A @ 2.5 ms)

Protection class III

Degree of protection IP 20

Ambient temperature range 0 … + 50 °C

Connecting screw terminals for cable 2x1,5 mm2

[mm] [mm]

BLE 176,5 300

BE 186,5 380

BLE + BKNE 236,5 300

BE + BKNE 251,5 380

* standard height of the flange

Weights and effective area cross section

1 14.3 0.0227 BLE 1 17.6 0.0511 BLE

2 16.4 0.0270 BLE 2 20.3 0.0608 BLE

2 17.3 0.0350 BLE 2 21.5 0.0788 BLE

2 18.3 0.0430 BLE 2 22.6 0.0968 BLE

2 19.2 0.0510 BLE 2 23.8 0.1148 BLE

3 21.2 0.0554 BLE 3 26.4 0.1246 BLE

3 22.2 0.0634 BLE 3 27.6 0.1426 BLE

3 24.1 0.0794 BLE 3 30.0 0.1786 BLE

4 27.0 0.0917 BLE 4 33.7 0.2063 BLE

4 28.9 0.1077 BLE 4 36.1 0.2423 BLE

5 34.5 0.1200 BE 5 42.5 0.2700 BE

5 36.4 0.1360 BE 5 44.8 0.3060 BE

6 39.3 0.1483 BE 6 48.6 0.3337 BE

6 41.2 0.1643 BE 6 51.0 0.3697 BE

1 15.1 0.0298 BLE 1 18.4 0.0582 BLE

2 17.4 0.0355 BLE 2 21.3 0.0693 BLE

2 18.4 0.0460 BLE 2 22.5 0.0898 BLE

2 19.4 0.0565 BLE 2 23.7 0.1103 BLE

2 20.4 0.0670 BLE 2 25.0 0.1308 BLE

3 22.5 0.0727 BLE 3 27.7 0.1419 BLE

3 23.5 0.0832 BLE 3 28.9 0.1624 BLE

3 25.5 0.1042 BLE 3 31.4 0.2034 BLE

4 28.7 0.1203 BLE 4 38.0 0.2349 BE

4 30.7 0.1413 BLE 4 40.5 0.2759 BE

5 36.5 0.1575 BE 5 44.5 0.3075 BE

5 38.5 0.1785 BE 5 47.0 0.3485 BE

6 41.6 0.1947 BE 6 50.9 0.3801 BE

6 43.6 0.2157 BE 6 53.4 0.4211 BE

1 15.9 0.0369 BLE 1 19.2 0.0653 BLE

2 18.3 0.0439 BLE 2 22.2 0.0777 BLE

2 19.4 0.0569 BLE 2 23.5 0.1007 BLE

2 20.5 0.0699 BLE 2 24.8 0.1237 BLE

2 21.5 0.0829 BLE 2 26.1 0.1467 BLE

3 23.8 0.0900 BLE 3 29.0 0.1592 BLE

3 24.9 0.1030 BLE 3 30.3 0.1822 BLE

3 27.0 0.1290 BLE 3 32.9 0.2282 BLE

4 30.3 0.1490 BLE 4 39.7 0.2636 BE

4 32.5 0.1750 BLE 4 42.3 0.3096 BE

5 38.5 0.1950 BE 5 46.5 0.3450 BE

5 40.6 0.2210 BE 5 49.1 0.3910 BE

6 43.9 0.2410 BE 6 53.2 0.4264 BE

6 46.1 0.2670 BE 6 55.8 0.4724 BE

1 16.8 0.0440 BLE 1 20.9 0.0795 BLE

2 19.3 0.0524 BLE 2 24.2 0.0946 BLE

2 20.4 0.0679 BLE 2 25.6 0.1226 BLE

2 21.6 0.0834 BLE 2 27.0 0.1506 BLE

2 22.7 0.0989 BLE 2 28.4 0.1786 BLE

3 25.1 0.1073 BLE 3 31.6 0.1938 BLE

3 26.2 0.1228 BLE 3 33.0 0.2218 BLE

3 28.5 0.1538 BLE 3 35.8 0.2778 BLE

4 32.0 0.1776 BLE 4 43.1 0.3209 BE

4 34.3 0.2086 BLE 4 45.9 0.3769 BE

5 40.5 0.2325 BE 5 50.5 0.4200 BE

5 42.7 0.2635 BE 5 53.3 0.4760 BE

6 46.3 0.2874 BE 6 57.9 0.5191 BE

6 48.5 0.3184 BE 6 60.7 0.5751 BE

Andere Handbücher für SEDS-L

Inhaltsverzeichnis

Andere Mandik Feuer- und Rauchklappe Handbücher

Mandik

Mandik MSD Bedienungsanleitung

Mandik

Mandik FDMB Bedienungsanleitung

Mandik

Mandik FDMR Bedienungsanleitung

Mandik

Mandik FDMS Bedienungsanleitung

Mandik

Mandik FDMD Bedienungsanleitung

Mandik

Mandik SEDS-R Bedienungsanleitung

Mandik

Mandik FDML Bedienungsanleitung

Mandik

Mandik SEDS Bedienungsanleitung

Mandik

Mandik SEDS-L Bedienungsanleitung

Mandik

Mandik RKM Bedienungsanleitung

Mandik

Mandik FDMD Bedienungsanleitung

Mandik

Mandik FDMB Bedienungsanleitung

Mandik

Mandik FDML Leitfaden

Mandik

Mandik NKTM Bedienungsanleitung

Mandik

Mandik MSD Square Konfigurationshandbuch

Mandik

Mandik alnor FDMD Bedienungsanleitung

Mandik

Mandik FDMB Bedienungsanleitung

Mandik

Mandik SEDS-L Leitfaden

Mandik

Mandik FDMB Bedienungsanleitung

Mandik

Mandik FDMA-PM Bedienungsanleitung

Mandik

Mandik SEDM-L Bedienungsanleitung

Mandik

Mandik FDMS Series Bedienungsanleitung

Mandik

Mandik CFDM Bedienungsanleitung

Mandik

Mandik MSD Bedienungsanleitung

Beliebte Feuer- und Rauchklappe Handbücher anderer Marken

HVC

HVC NCA 700 Series Bedienungsanleitung

Wildeboer

Wildeboer FR90 Bedienungsanleitung

FläktGroup

FläktGroup ETCE Programmierhandbuch

Tamco

Tamco 1000 SM Series Bedienungsanleitung

Greenheck

Greenheck Vektor-MD Bedienungsanleitung

Lindab

Lindab FBC2 Installations- und Betriebshandbuch

EKOVENT

EKOVENT EKO-SRB1 Montageanleitung

Greenheck

Greenheck HBS Series Handbuch

Advanced Air

Advanced Air 0160 Series Bedienungsanleitung

Greenheck

Greenheck CRD-1WT Bedienungsanleitung

Swegon

Swegon Actionair CSS Series Bedienungsanleitung

TAKACHIHO

TAKACHIHO FYN-M 1 Series Bedienungsanleitung

Valmet

Valmet Flowrox Expulse Series Handbuch

ETS NORD

ETS NORD NORDfire FDMB Bedienungsanleitung

AMS

AMS CR2 Bedienungsanleitung

Arzel

Arzel RegiDamper Bedienungsanleitung

mercor

mercor mcr S-THERM C Bedienungsanleitung

Greenheck

Greenheck FD Series Betriebsanleitung