Manitowoc SD0672C Bedienungsanleitung

KFC and Taco Bell Logo Application Instructions

Manitowoc Models S600C, S1470C

These instructions will help the location manager or machine installer to correctly center the urethane logo on the front panel of the

Manitowoc ice machine.

Tools Needed:

Philips head screw driver

Contents of Kit:

Small packet containing alcohol prep pad

Urethane logo

L-shaped static cling template

MODEL - SY0674C or SD0672C

Follow these instructions to remove the left section of the ice

machine front panel from the machine.

(1) If your machine is on a drink dispenser, remove the drink

dispenser ice bin cover.

(2) Remove the Philips head screw from lower section of the

front panel.

(3) Depress pin to release front panel.

Pictured: S600C

MODELS - SY1474C or SD1472C

Follow these instructions to remove the ice machine front panel

from the machine.

(1) If your machine is on a drink dispenser, remove the drink

dispenser ice bin cover.

(2) Remove the Philips head screw from lower section of the front

panel.

(3) Pull front panel away from machine while lifting slightly.

Manitowoc Ice, Inc.

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000002851

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Rev 01

Web Site - www.manitowocice.com 5/25/10

MODEL - SY0684C or SD0672C

MODELS - SY1474C or SD1472C

1. Place the panel on a flat, horizontal surface with the

stainless steel side (exterior) facing up.

Note: The screw hole on the face of the panel should be in the

lower right-hand corner when you are facing the panel, as

pictured below:

2. Make sure the white PVC film is removed from the front

panel.

3. Use the Alcohol Prep Pad found in the kit to gently clean

surface of stainless steel panel, focusing on the central

area highlighted below.

Models SY1474, SD1472 Models SY0684, SD0672

4. Find the large L-shaped template in the kit. Remove the

plastic static cling from the paper backing.

5. Carefully place the L-shaped static cling template in the

lower left-hand corner of the panel as shown in the

illustration below:

Note: Verify template rests on the top edge of the bottom

molding and is aligned with left edge of the panel.

Models SY1474, SD1472

Models SY0684, SD0672

6. Examine the urethane logo. Notice that it is covered on one

side by white backing paper and on the other by a thinner semi-

transparent masking film. Peel back the solid, white backing

paper slowly, making sure the urethane logo remains attached

to the thinner semi-transparent masking film. This must be

done very carefully, as the logo has a tendency to remain

attached to the solid white backing paper, and the logo

itself could be divided into several pieces.

Verify the entire logo remains attached to the semi-transparent film

as you peel it back

7. Carefully place the semi-transparent film and logo within the

inside edges of the template, making sure the edges of the

film are flush with the inside edges of the template, as

illustrated below.

Note: Be sure that the logo is aligned properly. It is difficult to re-

adjust the logo once the adhesive makes contact with the stainless

steel.

Manitowoc Ice, Inc.

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000002851

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Rev 01

Web Site - www.manitowocice.com 5/25/10

White paper

Semi-transparent film

Logo

8. When the semi-transparent masking and logo are in place,

apply pressure against the top of the masking, working

out any visible air bubbles. Remove the semi-transparent

logo masking very slowly, allowing only the urethane

logo to remain in the space within the template frame. As

the semi-transparent masking is pulled back, make sure

no stray pieces of urethane logo remain attached to

the semi-transparent masking. If this occurs, slowly

lower the masking and press firmly against it to make

sure the remaining piece sticks to the stainless steel.

9. Remove the template from the surface of the stainless

steel front panel.

10. Reattach the stainless steel front panel to the ice machine.

11. If the machine is on a beverage dispenser, re-attach the

drink dispenser ice bin cover.

Manitowoc Ice, Inc.

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000002851

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Rev 01

Web Site - www.manitowocice.com 5/25/10

Andere Handbücher für SD0672C

Dieses Handbuch passt für folgende Modelle

Andere Manitowoc Zubehör Handbücher

Manitowoc

Manitowoc K000187 Bedienungsanleitung

Manitowoc

Manitowoc 7623123 Bedienungsanleitung

Manitowoc

Manitowoc K00127 Bedienungsanleitung

Manitowoc

Manitowoc IB00820 Bedienungsanleitung

Manitowoc

Manitowoc K00221 Bedienungsanleitung

Manitowoc

Manitowoc 7626213 Bedienungs- und Sicherheitshinweise

Manitowoc

Manitowoc BULKHEAD Q-1400 Bedienungsanleitung

Manitowoc

Manitowoc AUCS Q Bedienungsanleitung

Manitowoc

Manitowoc K00105 Bedienungsanleitung

Manitowoc

Manitowoc K00142 Bedienungsanleitung

Manitowoc

Manitowoc 7603323 Bedienungsanleitung

Manitowoc

Manitowoc BR-0490N Bedienungsanleitung

Manitowoc

Manitowoc K00349 Bedienungsanleitung

Manitowoc

Manitowoc Q 76-0293-3 Bedienungsanleitung

Manitowoc

Manitowoc 7629661 Bedienungsanleitung

Manitowoc

Manitowoc K00067 Bedienungsanleitung

Manitowoc

Manitowoc RF0300 Bedienungsanleitung

Manitowoc

Manitowoc A-0100 Bedienungsanleitung

Manitowoc

Manitowoc 8930283 UK165S Bedienungsanleitung

Manitowoc

Manitowoc 7625573 Bedienungsanleitung

Manitowoc

Manitowoc 7628063 Bedienungsanleitung

Manitowoc

Manitowoc 1480279 Bedienungsanleitung

Manitowoc

Manitowoc K00346 Bedienungsanleitung

Manitowoc

Manitowoc MDB-290 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung