Market Forge Industries ST-7-TE Betriebsanleitung

MADE IN CANADA

S-6129 01/06

INSTALLATION AND OPERATION

MANUAL AND PARTS

ELECTRIC CONVECTION STEAMER

MODELS: ST-7-TE

ST-10-TE

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 22006-01-19

IMPORTANT NOTES FOR INSTALLATION AND OPERATION

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

WARNING: Improper installation, operation, adjustment, alteration,

service or maintenance can cause property damage, injury or death.

Read the installation, operating and maintenance instructions

thoroughly before installing, operating or servicing this equipment.

This manual should be retained for future reference.

Intended for commercial use only. Not for household use.

Adequate clearances must be maintained for safe and proper operation.

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 32006-01-19

TABLE OF CONTENTS

DESCRIPTION PAGE

Important Notes for Installation and Operation ....................................2

1.0 Service Connections ....................................................4

2.0 Installation Instructions ...................................................5

3.0 Operation ............................................................10

4.0 Suggested Cooking Guidelines ...........................................13

5.0 Cleaning .............................................................17

6.0 Maintenance .........................................................19

7.0 Troubleshooting .......................................................20

8.0 Service ..............................................................21

9.0 Parts ...............................................................23

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 42006-01-19

1.0 SERVICE CONNECTIONS

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 52006-01-19

2.0 INSTALLATION INSTRUCTIONS

This steamer was inspected before leaving the factory. The transportation company assumes

full responsibility for safe delivery upon acceptance of the shipment. Immediately after

unpacking the steamer, check for possible damage. If the steamer is found to be damaged

after unpacking, save the packaging material and contact the carrier within 15 days of delivery.

Prior to installation, verify that the electrical service agrees with the specifications on the

machine data plate which is located on the left side panel.

LOCATION

Allow space for plumbing and electrical connections. Minimum clearances are 3" (76 mm) on

the sides and 6" (152 mm) on the back for proper air circulation. Allow adequate access for

operating and servicing the steamer, 36" (915 mm) at the front of the steamer and 15" (381

mm) above the steamer.

LEVELLING AND ANCHORING

Using a spirit level or pan of water in the bottom of the steamer, adjust the levelling feet to level

the steamer front-to-back and side-to-side.

Mark hole locations on the floor through the anchoring holes provided in the flanged adjustable

feet. Remove the steamer and drill holes at marked locations on the floor. Insert proper

anchoring devices.

Set steamer back in proper position.

Install bolts through anchoring holes and into anchors to secure the steamer to the floor. Seal

bolts and flanged feet with Silastic.

After the drain is connected, check for level by pouring water onto the floor of the compartment.

All water should drain through the opening at the back of the compartment cavity.

ELECTRICAL CONNECTION

WARNING: Electrical and grounding connections must comply with

applicable portions of the national electrical code and/or other local

electrical codes.

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 62006-01-19

INSTALLATION INSTRUCTIONS (Continued)

WARNING: Disconnect the power supply to the appliance before

cleaning or servicing.

Make electrical connection through the 1-1/8" (29 mm) diameter hole provided using 3/4" (19

mm) trade size conduit. Refer to the wiring diagram located inside the right side panel. Use

90°C minimum insulated wire.

PLUMBING CONNECTIONS

WARNING: Plumbing connections must comply with applicable

sanitary, safety, and plumbing codes.

The water supply inlets are provided with 3/8" (10 mm) compression fittings for 3/8" O.D.

copper tubing. The water supply line pressure should be 25 - 50 psi (170 - 345 kPa) for each

line. The water supply to the generator tank is separate from the water supply to the cooling

system where steam is condensed before entering the drain line.

Install line strainers (not provided). A manual shutoff valve for each supply line must be

provided convenient to the steamer.

We recommend treated water feeding the boiler inlet supply, and untreated water feeding the

cooling system inlet. Hook-ups are labelled on the back of the steamer.

ADJUSTMENT FOR HIGH ALTITUDE LOCATIONS

The steamer has been factory set so that when it is ON, and during the READY phase, it will

maintain water temperature in the steam generator tank at approximately 205°F (96°C) (just

below water boiling point). However, for high altitude locations, an authorized service agency

must adjust the steamer to achieve this temperature.

ADJUSTMENT FOR DRAIN WATER TEMPERATURE

Cooling solenoid valves have been adjusted to yield drain temperatures of 140°F. This will vary

depending on install location water supply temperature and pressure. A qualified service person

should adjust the cooling solenoid valves should the drain temperature be other than desired.

Refer to section 8.0 Service on page 21 for adjustment instructions.

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 72006-01-19

FIGURE 1

DRAIN CONNECTIONS

The drain connection must be 1" (25 mm)

IPS down, preferably with one or two

elbows only, maximum length 6 feet (1830

mm) and piped to an open gap type drain

(Figure 1). Drain pipe to be copper only.

DO NOT use PVC pipe – PVC pipe may

lose its rigidity or glue may fail.

CAUTION: To avoid

injury or damage to the

steamer, do not connect

solidly to any drain

connection.

WATER QUALITY

The water supply connected to the steam generator should meet the following guidelines:

Failure to comply with water quality statement on page 4 may void the warranty.

Water supplies vary from one location to another. Other factors affecting steam generation are

iron content, chlorides, and dissolved gasses. A local water treatment specialist should be

consulted before installing any steam generating equipment.

Untreated water contains scale producing minerals which can precipitate onto the surfaces in

the boiler. Due to the temperatures in the boiler, the minerals can bake onto the surfaces and

components. This can result in early component failure and reduced product life.

Mineral scale on components causes several problems:

1. The surfaces of the heating devices become coated with scale, reducing the heat transfer

efficiency. This can produce hot spots on the heating elements and result in premature

failure.

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 82006-01-19

WATER QUALITY (Continued)

2. The water level probes become coated with scale. Scale will bridge across the probe

insulator from the metal extension which senses the water level in the boiler shell. Once

this scale becomes wet, the water level control is unable to maintain the proper water level

in the boiler. This situation may cause an electric heating element to fail if the element is

not adequately covered by water.

Strainers and filters will not remove minerals from the water.

Refer to REMOVAL OF LIME SCALE DEPOSITS, page 19.

VENT HOOD

Some local codes may require the steamer to be located under an exhaust hood. Information

on the construction and installation of ventilating hoods may be obtained from NFPA Standard

No. 96, Vapor Removal from Cooking Equipment, (latest edition).

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 92006-01-19

START-UP TEST

WARNING: The steamer and its parts are hot. Use care when

operating, cleaning or servicing the steamer. The cooking

compartment contains live steam. Stay clear while opening the

door.

Once the steamer is installed and all mechanical connections have been made, thoroughly test

the steamer before operation.

1. Check that proper water, drain, and electrical connections have been made.

2. Turn main power switch ON. After approximately 15 minutes, the READY light should come

on, indicating that the water temperature is 205°F (96°C).

3. When the READY light comes on, set the timer at 5 minutes. With door open, observe that

no steam is entering the compartment and the COOKING light is OFF.

4. Close compartment door. The COOKING light should now be lit and steam should be

heard entering the compartment after about 45 seconds (5 minutes if boiler is empty).

5. Check drain line to ensure that water from the cold water condenser is flowing through the

drain line.

6. Open compartment door and observe that steam supply to the chamber is cut off (READY

light should again come on and COOKING light goes off).

7. Close compartment door and let cooking cycle finish. When the timer returns to the “O”

position, a buzzer will sound, signalling the end of the cooking cycle. To silence the buzzer,

turn the dial timer to OFF.

8. Complete the above steps for each cooking compartment.

9. To shut the steamer down, turn the main power switch OFF and leave the compartment

doors slightly open to allow the inside to dry out.

INSTALLATION AND OPERATION MANUAL AND PARTS,

ELECTRIC CONVECTION STEAMERS, MODELS: ST-7-TE, ST-10-TE

PART NUMBER 10175R2 10 2006-01-19

3.0 OPERATION

CAUTION: Live steam and accumulated hot water in the

compartment may be released when the door is opened.

CAUTION: An obstructed drain can cause personal injury or

property damage.

CONTROLS

Main Power Switch

ON - The boiler will automatically fill and begin heating to the preset

temperature.

OFF -The boiler will drain.

DELIME - Closes the drain valve while CLR liquid is being poured into the

generator during the delime procedure.

Ready Light -Indicates the temperature has reached 205°F and that the

steamer is ready to begin cooking.

Cooking Light -Indicates that a cooking cycle is in progress.

Timer -Set the cooking time (0 to 60 minutes) or constant steam. Steam

cooking will begin when the door is closed. The cooking cycle will

be interrupted if the door is opened during the cooking cycle;

resume cooking by closing the door.

When done, a buzzer sounds and steam supply to the cooking

chamber will cease. Turn the timer OFF to stop the buzzer.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Market Forge Industries Elektrischer Dampfgarer Handbücher

Market Forge Industries

Market Forge Industries 3500 SERIES Bedienungsanleitung

Market Forge Industries

Market Forge Industries TS-3E Kurzanleitung

Market Forge Industries

Market Forge Industries MPS-3E Bedienungsanleitung

Market Forge Industries

Market Forge Industries ST-6-TGG Bedienungsanleitung

Market Forge Industries

Market Forge Industries ST-E Leitfaden

Market Forge Industries

Market Forge Industries ST-24 Bedienungsanleitung

Market Forge Industries

Market Forge Industries Premier PS-3E Kurzanleitung

Market Forge Industries

Market Forge Industries ST-10 Power-Plus Bedienungsanleitung

Market Forge Industries

Market Forge Industries Eco Tech ET-3E Bedienungsanleitung

Market Forge Industries

Market Forge Industries TURBO STEAM SERIES Betriebsanleitung

Market Forge Industries

Market Forge Industries STEAM-TECH PLUS STP-6E Bedienungsanleitung

Market Forge Industries

Market Forge Industries 3500 SERIES Kurzanleitung

Beliebte Elektrischer Dampfgarer Handbücher anderer Marken

Eloma

Eloma Joker B Gebrauchsanweisung

Clatronic

Clatronic DG 3547 Bedienungsanleitung

Heaven Fresh

Heaven Fresh NaturoPure HF 8333 Bedienungsanleitung

Memco

Memco 6625B Handbuch

Braun

Braun 3216 Bedienungsanleitung

Kooper

Kooper 2165306 Bedienungsanleitung

Morphy Richards

Morphy Richards FS48751MEE Bedienungsanleitung

Cuisinart

Cuisinart STM1000AR Bedienungsanleitung

Hastings

Hastings DIRECT GAS FIRED ELECTRIC STEAM Kurzanleitung

Galantine

Galantine SILVER Style SC-5003B Bedienungsanleitung

Cleveland

Cleveland SteamChef 22CET3.1 Bedienungsanleitung

Cleveland

Cleveland Enodis 24-CDM Bedienungsanleitung

Oster

Oster 5711 Bedienungsanleitung

Back to Basics

Back to Basics NUTRI STEAMER L5725A 01/09 Bedienungsanleitung

Gallet

Gallet CUV 968 Colmar Bedienungsanleitung

Rasonic

Rasonic RSB-B1CR Bedienungsanleitung

Basilico

Basilico K047 Bedienungsanleitung

Cuisinart

Cuisinart Cook & Steam Bedienungsanleitung