Martin MAC Encore Performance CLD Einrichtungshandbuch

MAC Encore™ Performance

CLD and WRM

Safety and Installation Manual

Dimensions

All measurements are given in millimeters

550

254

585

238

452

724

733

Information subject to change without notice. HARMAN Professional Denmark ApS disclaims liability for any injury, damage, direct or

indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information

contained in this document.

registered in the United States and other countries. Features, specifications and appearance are subject to change without notice.

HARMAN Professional Denmark - Olof Palmes Allé 18 - 8200 Aarhus N - Denmark

www.martin.com

MAC Encore™ Performance Safety and Installation Manual, P/N 5085516, Rev. C

Contents

Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DMX data link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Service and maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Tilt lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Access to the head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Access to the multi-module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Replacing optical components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the fixture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Applying power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4 MAC Encore™ Performance Safety and Installation Manual

Safety Information

The following symbols are used to identify important safety information on the product and in this document:

Warning! The MAC Encore™ Performance™ contains components that are accessible and live at

high voltage while the fixture is connected to power. These components remain under tension for up

to 30 minutes after power is disconnected. Only technicians who are authorized by Martin® and who

have access to the Martin® service documentation for the MAC Encore™ Performance are permitted

to open the fixture.

Warning! Risk Group 2 product according to EN 62471. This product produces intense light output

that may be hazardous if suitable precautions are not taken. Do not view the light output with optical

instruments or any device that may concentrate the beam.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls if

the safety precautions in this manual are not followed.

Read this manual before installing, powering or servicing the fixture. Follow the safety precautions and

observe all warnings in this manual, in the MAC Encore™ Performance User Guide, and printed on the

fixture.

The latest versions of this Safety and Installation Manual and the MAC Encore™ Performance User Guide

are available for download from the MAC Encore™ Performance Support & Downloads page on the

Martin® website at www.martin.com. Before you install, operate or service the MAC Encore™ Performance,

check the Martin® website and make sure that you have the latest user documentation for the fixture.

Document revisions are indicated at the bottom of page 2.

The product is for professional use only. It is not for household use. Respect all locally applicable laws,

codes and regulations when installing, powering, operating or servicing the fixture.

Install, operate and service Martin® products and accessories only as directed in their user documentation,

or you may create a safety hazard or cause damage that is not covered by product warranties.

If you have questions about how to operate the fixture safely, please contact your Martin® supplier or call

the Martin® 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.

PROTECTION FROM ELECTRIC SHOCK

• Do not remove any cover from the fixture except as described under “Service and maintenance” on

page 13.

• Disconnect the fixture from AC power before servicing it and when it is not in use.

• Ensure that the fixture is electrically connected to ground (earth).

• Use only a source of AC power that complies with local building and electrical codes and has both

overload and ground-fault (earth-fault) protection.

WARNING!

Read the safety precautions in this section before

installing, powering, operating or servicing this

product.

DANGER!

Safety hazard.

Risk of severe

injury or death.

DANGER!

Hazardous

voltage. Risk of

lethal or severe

electric shock.

WARNING!

Fire hazard.

WARNING!

Burn hazard. Hot

surface. Do not

touch.

WARNING!

Intense light

emission.

WARNING! Refer

to user

documentation.

Safety Information 5

• The cable used to connect the fixture to AC power must be 14 AWG or 1.5 mm2minimum conductor size

and heat-resistant to 90° C (194° F) minimum. It must have three conductors and an outer cable diameter

of 5 - 15 mm (0.2 - 0.6 in.). In the USA and Canada, the cable must be UL/CSA-recognized, hard usage,

type SJT or equivalent. In the EU, the cable must be type H07RN-F or equivalent.

• Before using the fixture, check that all power distribution equipment and cables are in perfect condition

and rated for the current requirements of all connected devices.

• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component

is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs

have been completed.

• Use only a Neutrik TRUE1 NAC3FX-W cable connector to connect to the power input socket.

• Do not expose the fixture to rain or moisture.

• The MAC Encore™ Performance contains components that are accessible and live at high voltage while

the fixture is connected to power and that remain under tension for 30 minutes after power is

disconnected. Only technicians who are authorized by Martin® and who have the Martin® service

documentation for the MAC Encore™ Performance are permitted to open the fixture.

• Refer any service operation not described in this manual or in the MAC Encore™ Performance User

Guide to Martin® Service or an authorized Martin® Service partner.

• The light source contained in this fixture may only be replaced by Martin® Service or an authorized

Martin® Service partner.

PROTECTION FROM BURNS AND FIRE

• The exterior of the fixture becomes hot during use. After 5 minutes of operation a surface temperature of

75° C (167° F) shall be expected. The maximum steady state surface temperature is also 75° C (167° F).

Avoid contact by persons and materials.

• Allow the fixture to cool for at least 30 minutes before handling.

• Keep all combustible materials (e.g. fabric, wood, paper) at least 0.2 m (8 in.) away from the fixture.

• Keep flammable materials well away from the fixture.

• Ensure that there is free and unobstructed airflow around the fixture.

• Provide a minimum clearance of 0.2 m (8 in.) around fans and air vents.

• Do not illuminate surfaces within 2.0 m (6.6 ft.) of the fixture.

• Do not expose the front glass to sunlight or any other strong light source from any angle. Lenses can

focus the sun's rays inside the fixture, creating a potential fire hazard.

• Do not attempt to bypass thermostatic switches or fuses.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• Do not modify the fixture in any way not described in this manual or the fixture’s User Guide or install other

than genuine Martin® parts. Do not stick filters, masks or other materials onto any lens or other optical

component. Use only accessories approved by Martin® to mask or modify the light beam.

PROTECTION FROM EYE INJURY

• This fixture is a Risk Group 2 product according to EN 62471. It emits possibly hazardous optical

radiation. It falls into the Risk Group categories shown below according to EN 62471.

• Do not look directly into the fixture’s light output.

• Do not expose persons to the fixture’s light output from a distance of less than 0.2 m (8 ins.).

• Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may

concentrate the light output.

• Ensure that persons are not looking at the LEDs when the fixture lights up suddenly. This can happen

when power is applied, when the fixture receives a DMX signal, or when certain control menu items are

selected.

DO NOT RISK GROUP

RISK GROUP

0.2 m

(7.9 ins.)

16.5 m

(54.2 ft.)

18.6 m

(61.1 ft.)

EXPOSE

RISK GROUP

EXEMPT

6 MAC Encore™ Performance Safety and Installation Manual

• To minimize the risk of eye irritation or injury, disconnect the fixture from power at all times when the

fixture is not in use, and provide well-lit conditions to reduce the pupil diameter of anyone working on or

near the fixture.

PROTECTION FROM INJURY

• Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when

installed.

• Do not lift or carry the fixture alone.

• Use two evenly spaced omega brackets with clamps to suspend the fixture from rigging structures. Do not

use only one clamp.

• When clamping the fixture to a truss or other supporting structure at any other angle than with the yoke

hanging vertically downwards, use two half-coupler clamps. Do not use G-clamps, quick-trigger clamps or

any other type of clamp that does not completely encircle the supporting structure when fastened.

• When suspending the fixture, check that the supporting structure and all hardware used to suspend the

fixture can hold at least 10 times the weight of all devices suspended from them and that the installation

respects all similar safety factors that are required by locally applicable regulations. Check that the

structure and hardware are in perfect condition and suitable for their purpose.

• If the fixture is installed in a location where it may cause injury or damage if it falls, install as described in

this manual a secondary attachment such as a safety cable that is approved by an official body such as

TÜV as a safety attachment for the weight that it secures. The safety cable must comply with EN

60598-2-17 Section 17.6.6 or BGV C1 / DGUV 17, and must be capable of bearing a static suspended

load at least six times (or more if required by locally applicable regulations) the weight that it secures.

• Eliminate as much slack as possible in the secondary attachment (by looping the safety cable more than

once around the rigging truss, for example).

• If the safety cable attachment point becomes deformed, do not suspend the fixture. Have the fixture

repaired by an authorized Martin® service partner.

• Check that all external covers and rigging hardware are securely fastened.

• Block access below the work area and work from a stable platform whenever installing, servicing or

moving the fixture.

• Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture

when it moves.

Introduction 7

Introduction

Thank you for selecting the MAC Encore™ Performance from Martin®. This moving-head spotlight is

available in CLD (cold white LED) and WRM (warm white LED) variants. Both variants offer the following

features:

• CLD (cold white LED) and WRM (warm white LED) variants

• Powerful white LED engine

• Full-spectrum CMY color mixing and color temperature control

• Color wheel

• Rotating gobo wheel

• Gobo animation

• Frost effect

• Iris effect

• Motorized zoom and focus

• Rotating framing

• Pre-programmed synchronizable FX (effect combination presets) including Animotion FX

• Full-range dimming with four dimming curve options

• Electronic shutter effect with variable speed regular and random strobe

• Backlit graphic display and battery power (mains power not required for fixture setup)

• Auto-sensing switch-mode power supply.

For the latest firmware updates, documentation, and other information about this and all Martin® products,

please visit the Martin® website at http://www.martin.com

Comments or suggestions regarding this document may be e-mailed to service@martin.dk or posted to:

Technical Documentation, Martin® Professional, Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark.

Unpacking

The MAC Encore™ Performance is packed in a cardboard box that is designed to protect the fixture during

shipment. Two packaging options are available in the cardboard box – the fixture can be supplied in either:

• expanded polystyrene that is not intended for re-use, or

• a SIP (Superior Impact Protection) insert that is designed to be installed in the 2-unit Martin® MAC

Encore™ Performance flightcase or custom-made flightcases.

This Safety and Installation Manual is included with the fixture. The MAC Encore™ Performance User

Guide, containing full details of setting up, controlling and monitoring the fixture, is available for download

from the MAC Encore™ Performance Product Support page on the Martin® website at www.martin.com. If

you have any difficulty locating either of these two documents, please contact your Martin® supplier for

assistance.

8 MAC Encore™ Performance Safety and Installation Manual

Tilt lock

Release the tilt lock before applying power to the fixture.

See Figure 1. Release the tilt lock by pushing the lock in

towards the yoke (you can reapply the tilt lock by first

checking that the power is off and then pushing the lock

back in towards the yoke from the other side).

Packing

Important! Allow the fixture to cool and release the tilt lock

before packing it in its flightcase.

A rugged two-unit flightcase (see Figure 2) is available

from Martin® for the MAC Encore™. The flightcase

accepts two durable molded SIP (Superior Impact

Protection) foam inserts that are supplied in cardboard boxes with fixtures if you select the SIP option at

time of ordering.

The SIP inserts are designed to protect the head without the tilt lock (see Figure 1) applied. Release the tilt

lock before putting a fixture into a flightcase for transport. Leaving the tilt lock applied may cause damage

that is not covered by the product warranty.

Figure 1: Tilt lock

Figure 2: Martin® flightcase for the MAC Encore

Physical installation 9

Physical installation

Warning! The MAC Encore™ Performance has a powerful pan motor. The torque reaction when the

head is panned suddenly can cause the base to move if the fixture is standing unsecured on a

surface. Do not apply power to the MAC Encore™ Performance unless the base is securely fastened

to a surface or to rigging hardware.

Warning! Use two clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each

clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 90° clockwise.

Warning! When suspending the fixture above ground level, secure it against failure of primary

attachments by attaching a safety wire that is approved as a safety attachment for the weight of the

fixture to the attachment point in the base. Do not use the carrying handles for secondary

attachment.

Warning! When clamping the fixture to a truss or other structure at any other angle than with the

yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of

clamp that does not completely encircle the structure when fastened.

Warning! Position or shade the head so that the front lens will not be exposed to sunlight or another

strong light source from any angle – even for a few seconds. See Figure 3. The MAC Encore™

Performance’s lens can focus the sun's rays, creating a potential fire hazard and causing damage.

Important! Do not point the output from other lighting fixtures at the MAC Encore™ Performance, as

powerful light can damage the display.

See Figure 3. Lenses can focus sunlight and

strong light, presenting a risk of fire and

damage to the fixture. Shield or shade the

head if necessary.

The MAC Encore™

Performance can be fastened to

a surface such as a stage or

clamped to a truss in any

orientation. Clamps must be

half-coupler type (see Figure 5)

or equivalent type that fully

encircles the truss unless the

fixture is installed with the yoke

hanging vertically downwards,

in which case other clamp types

that are approved for the

supported weight may be used.

The mounting points in the base

allow omega brackets and

rigging clamps to be fastened

as shown in Figure 4.

Figure 3: Potential sunlight damage

Figure 4: Clamp bracket positions

10 MAC Encore™ Performance Safety and Installation Manual

Clamping the fixture on a truss

1. Check that all rigging hardware is undamaged and can bear at least 10 times the weight of the fixture or

as required by locally applicable regulations. Check that the supporting structure can safely bear the

weight of all installed fixtures, clamps, cables, auxiliary equipment, etc. and complies with locally

applicable regulations.

2. Bolt each rigging clamp securely to an omega bracket with an M12 bolt (minimum grade 8.8) and

self-locking nut.

3. See Figure 4 on page 9. Align the first clamp

and bracket with 2 mounting points in the base,

and engage both the clamp bracket’s

quarter-turn fasteners in corresponding sockets

in the base. See Figure 5. Turn the levers on

the quarter-turn fasteners a full 90° clockwise

to lock. Repeat for the second clamp.

4. Block access under the work area. See Figure

6. Note the position of the arrow marked

FRONT on the base of the fixture. Working

from a stable platform, hang the fixture on the

truss with the arrow marked FRONT facing

towards the area to be illuminated. Tighten the

rigging clamps.

5. See Figure 7. Install a safety cable that is

approved as a safety attachment for the weight

of the fixture by looping it through the safety

attachment point (arrowed) in the bottom of the

base and around a secure anchoring point so

that the safety cable will catch the fixture if a primary attachment fails. Remove as much slack as

possible from the safety cable (by looping it twice around the anchoring point, for example).

6. Check that the tilt lock is released. Check that

there are no combustible materials within 0.2 m

(8 in.) or surfaces to be illuminated within 2.0 m

(6.6 ft.) of the fixture, and that there are no

flammable materials nearby.

7. Check that there is no possibility of heads or

yokes colliding with other fixtures. Note that

pan and tilt range on the MAC Encore™

Performance can be limited via the control

panel to allow fixtures to be installed closer to

each other or to obstacles with no risk of

collision (see User Guide for details).

8. Check that other lighting fixtures cannot project

light at the MAC Encore™ Performance, as

powerful illumination can damage the fixture’s

display.

Figure 5: Martin® rigging hardware

Half-coupler Omega bracket for

rigging clamp rigging clamp attachment

90°

Locking quarter-

turn fasteners

SAFETY CABLE

Figure 6: Front of fixture

SAFETY CABLE

Figure 7: Safety cable attachment point

Andere Handbücher für MAC Encore Performance CLD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Martin DJ-Equipment Handbücher

Martin

Martin MAC III Quadray Module Gebrauchs- und Wartungshandbuch

Martin

Martin THRILL Compact PAR 64 LED Einrichtungshandbuch

Martin

Martin MAC Allure Wash PC Bedienungsanleitung

Martin

Martin Exterior Projection 1000 Bedienungsanleitung

Martin

Martin MAC Axiom Hybrid Bedienungsanleitung

Martin

Martin LC 2140 Bedienungsanleitung

Martin

Martin Alien 05 Bedienungsanleitung

Martin

Martin RUSH PAR 4 UV Bedienungsanleitung

Martin

Martin Starflash III Bedienungsanleitung

Martin

Martin RUSH MH 10 Beam FX Bedienungsanleitung

Martin

Martin RUSH MH 7 Hybrid Bedienungsanleitung

Martin

Martin THRILL Multi-FX LED Einrichtungshandbuch

Martin

Martin Ego X4 Bedienungsanleitung

Martin

Martin THRILL Mini Profile Bedienungsanleitung

Martin

Martin RUSH PAR 3 RGB Bedienungsanleitung

Martin

Martin Exterior Inground 400 Bedienungsanleitung

Martin

Martin Punisher X250 Bedienungsanleitung

Martin

Martin M-Series Bedienungsanleitung

Martin

Martin MAC Quantum Profile Bedienungsanleitung

Martin

Martin MAC 2000 Profile II Handbuch

Martin

Martin ELP WW Bedienungsanleitung

Martin

Martin Rush Multibeam 2 Bedienungsanleitung

Martin

Martin MAC 575 Krypton Bedienungsanleitung

Martin

Martin Exterior Wash 120 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung