Maxouttech RF-CMDWS-OD-319-NN Bedienungsanleitung

RF-CMDWS-OD-319-NN Installation Instructions

I-RF-CMDWS-OD-319-NN Rev.3 Oct. 2020

For updated Installation Manual Revision go to Maxouttech.com and select Documentation page.

Description

The Outdoor Sensor is a supervised,

wireless sensor that detects openings and

closings. The unique design allows

mounting the device outdoors. The sensor

and magnet are mounted using screws

(included) or straps to secure to a post.

When activated, the sensor transmits an

open (trip) or close (restore) signal to the

panel. These are the signals the unit

provides: supervisory, tamper and low

battery (as needed). The sensor is powered

by (2) replaceable 3-VDC, lithium coin-cell

batteries.

Installation Guidelines

• Mounting the sensor on metal can affect

the transmitting range and magnet gap

performance. Therefore, test the sensor

from the desired location using the installer

sensor test, before permanently mounting it.

• Mount the sensor on a non-moving frame

or post, allowing the magnet to move

activating the sensor.

• Mount sensors at least 5 inches above the

ground to avoid damaging them.

• The sensors can be mounted to either

wood or metallic surfaces.

• The magnet should be mounted within 7/8”

for wood or 1/2” for metal installations.

Based on the magnet mounting spacing,

direction of operation and material of the

mounting surface, the gap for opening will

vary between 1/8” and 1 ¾”. Desired

operation should be checked before

permanent installation.

• After mounting the sensor, re-test the

sensor using the procedure in the section

“Testing the Sensor.”

Mounting the Sensor

Mount the sensor using the supplied mounting

screws for permanent mounting installations.

Note: The gap between the sensor and magnet

should not exceed a maximum of 3/8”.

Mounting Screws

1. Remove the cover screw from the sensor.

2. Mount the magnet into the desired location

using the supplied, making sure the alignment

mark lines up with the sensor mark.

Using Mounting Straps

1. The sensor case is designed for strap

mounting. Using a plastic tie strap wrap the

strap around the mounting post and through the

sensor.

Mount the sensor with 3

mounting screws

Mount the magnet

with 2 mounting

screws

RF-CMDWS-OD-319-NN Installation Instructions

I-RF-CMDWS-OD-319-NN Rev.3 Oct. 2020

For updated Installation Manual Revision go to Maxouttech.com and select Documentation page.

2. The magnet can also be strap mounted by

running a strap through the slot in the magnet

housing

External Contact

An external contact can be connected to the

transmitter by feeding contact wiring

through the rubber grommet.

Note: Only one set of contacts can be used

at one time the internal or external, for

added security the internal reed switch can

be cut.

Programming

The following steps describe the general

guidelines for programming the sensor into

panel memory. Refer to the specific panel’s

documentation for complete programming

details.

1. Set the panel to the program mode.

2. Proceed to the SENSORS menu.

3. Select the appropriate sensor group and

sensor number assignments.

4. When prompted by the panel to trip the

sensor for learning, remove the sensor

cover and if present pull the battery pull

tabs. The system should acknowledge

learning the sensor by touchpad display

and/or audio (depending on the panel).

5. Exit program mode.

Testing the Sensor

1. Set the panel to the sensor test mode.

2. Take the sensor and magnet to the

desired mounting location, making sure to

line up their alignment marks with each

other. Trip the sensor by pulling the magnet

away from the sensor.

3. Monitor the system after tripping the

sensor. Refer to the specific panel

documentation for interpretation of the

results to ensure desired signal strength is

achieved.

Note: If a low battery alarm occurs, replace

the battery within 7 days.

CAUTION: Battery may explode if

mistreated. Do not recharge, disassemble

or dispose of in fire.

Note: Make sure straps are

tight to prevent the sensor

from sliding away from the

magnet.

Note: Make sure straps are

tight to prevent the sensor

from sliding away from the

magnet.

Note: Do not exceed 50ft when wiring

to an external contact

RF-CMDWS-OD-319-NN Installation Instructions

I-RF-CMDWS-OD-319-NN Rev.3 Oct. 2020

For updated Installation Manual Revision go to Maxouttech.com and select Documentation page.

Specifications

Model no.

RF-CMDWS-OD-319-NN

RF frequency

319 MHz

Compatibility

UTC®, Interlogix®, GE®, ITI®

and Qolsys® control panels

Battery type

(2) 3-VDC, lithium coin-cell

battery (Varta or Panasonic,

Model CR2032)

Battery

Varta CR2032

Panasonic CR2032

Operating

temperature

range

32 to 120°F (0 to 49°C)

Storage

temperature

range

-30 to 140°F (-34 to

60°C)

Relative

humidity

95% non-condensing

Dimensions

(L x W x D)

2.25 x 1.0 x 0.50 in.

FCC / IC Statement

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada

exempts de licence standard RSS (s). Son

fonctionnement est soumis aux deux conditions

suivantes: (1) cet appareil ne doit pas provoquer

d'interférences et (2) cet appareil doit accepter toute

interférence, y compris celles pouvant causer un

mauvais fonctionnement de l'appareil.

In accordance with FCC requirements of human

exposure to radio frequency fields, the radiating

element shall be installed such that a minimum

separation distance of 20 cm is maintained from the

general population.

FCC: 2ABBZ-RF-CMDWS-319

IC: 11817A-RFCMDWS319

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation. Changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to operate

the equipment.

This Class B digital apparatus complies with

Canadian ICES-3B.

Cet appareil numérique de la classe B est conforme à

la norme NMB-003 du Canada.

MANUFACTURER HEREBY DISCLAIMS ALL

WARRANTIES AND REPRESENTATIONS, WHETHER

EXPRESS, IMPLIED, STATUTORY OR OTHERWISE

INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE WITH RESPECT TO THESE

PRODUCTS AND ANY RELATED SOFTWARE.

MANUFACTURER FURTHER DISCLAIMS ANY OTHER

IMPLIED WARRANTY UNDER THE UNIFORM

COMPUTER INFORMATION TRANSACTIONS ACT OR

SIMILAR LAW AS ENACTED BY ANY STATE.

(USA only) SOME STATES DO NOT ALLOW THE

EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE

EXCLUSION MAY NOT APPLY TO YOU. THIS

WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND

YOU MAY ALSO HAVE OTHER LEGAL RIGHTS THAT

VARY FROM STATE TO STATE.

MANUFACTURER MAKES NO REPRESENTATION,

WARRANTY, COVENANT OR PROMISE THAT ITS ALARM

PRODUCTS AND/OR RELATED SOFTWARE (I) WILL NOT

BE HACKED, COMPROMISED AND/OR CIRCUMVENTED;

(II) WILL PREVENT, OR PROVIDE ADEQUATE WARNING

OR PROTECTION FROM, BREAK-INS, BURGLARY,

ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN ALL

Andere Maxouttech Zubehör Handbücher

Maxouttech

Maxouttech RF-CMDWSX-345-NN Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung