Maxx Cold MXMC34HC Bedienungsanleitung

MXMC49HC

MXMC58HC

MILK COOLERS

Service, Installation and Care Manual

IMPORTANT INFORMATION

PLEASE READ CARFEULLY

MXMC34HC

Service and Installation Manual

CONTENTS

SERIAL NUMBER INFORMATION……...………………..……………………………………………………….3

RECEIVING AND INSPECTING THE EQUIPMENT……………………………………….…………………..3

COMMERICAL REFRIGERATION SAFETY & WARNINGS …………..…………….…………………….…4

SPECIFICATIONS…………………………………………………….……………………….………6

CONGRATULATIONS ON YOUR NEW COOLER…………………………………….………6

INSTALLATION………………………………………………………………………….…………..6-7

ELECTRICAL CONNECTION……………………………………………………………………….....….7

FOOD STORAGE.………………………………………………….………………………………………7

OPERATING INSTRUCTIONS……………………………………………………………………..…………7-9

MAINTENANCE…………………..……............…………………………… ………….……………….9-10

TROUBLESHOOTING……………………………………………………………………………………….11

DISPOSAL……………………………………………………………………………………………………12

SPECIAL POINTS TO NOTE………………………………………………………………………………12

EXPLODED VIEW AND PARTS LISTING………………………………………………………………..…13

WIRING/CIRCUIT DIAGRAM……………………………………………………………………………14

READ THIS MANUAL COMPLETELY BEFORE ATTEMPTING TO INSTALL OR

OPERATE THIS EQUIPMENT. SAVE THESE INSTRUCTIONS!

NOTIFY CARRIER OF DAMAGE! INSPECT ALL COMPONENTS IMMEDIATELY.

Service and Installation Manual

SERIAL NUMBER INFORMATION

The serial number of the milk cooler is located inside the unit on the left-hand side near the top on the wall.

Always have the serial number of your unit available when calling for parts or service. Also, retain proof of

purchase including the order date or your warranty will be voided.

This manual covers standard units only. If you have a custom unit, consult the customer service department

at the number listed in the back cover.

RECEIVING AND INSPECTING THE EQUIPMENT

Even though most equipment is shipped crated, care should be taken during unloading so the equipment is

not damaged while being moved into the building.

1. Visually inspect the exterior of the package and skid or container. Any damage should be noted and

reported to the delivering carrier immediately.

2. If damaged, open and inspect the contents with the carrier.

3. In the event that the exterior is not damaged, yet upon opening, there is concealed damage to the

equipment notify the carrier. Notification should be made verbally as well as in written form.

4. Request an inspection by the shipping company of the damaged equipment. This should be done

within 10 days from receipt of the equipment.

5. Be certain to check the compressor compartment housing and visually inspect the refrigeration

package. Be sure lines are secure and base is still intact.

6. Freight carriers can supply the necessary damage forms upon request.

7. Retain all crating material until an inspection has been made or waived.

8. Advise our customer technical support department of any filed damage claims with the carrier.

Service and Installation Manual

COMMERCIAL REFRIGERATION SAFETY

Your safety and the safety of others are very important.

We will provide important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

Our product instructions will be uploaded on our company website.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can

kill or injury you and others. All safety messages will follow the Safety Alert Symbol

and either the words” DANGER”, “WARNING” or “CAUTION”.

Danger means that failure to heed this safety

statement may result in severe personal injury or

death.

Warning means that failure to heed this safety

statement may result in extensive product

damage, serious personal injury, or death.

Caution means that failure to heed this safety

statement may result in minor or moderate

personal injury, or property or equipment damage.

All safety messages will alert you to what the potential hazard is, tell you how to reduce the chance of injury,

and let you know what can happen if the instructions are not followed.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with this appliance.

This appliance can be used by children aged from 8 years and above and persons with reduced physical

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children

shall not play with the appliance. Cleaning and user maintenance shall not be made by children without

supervision.

Keep the appliance and electrical its cord out of reach of children less than 8 years old.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

Service and Installation Manual

WARNING

The appliance uses flammable insulation blowing gas C5H10, disposal of the appliance must be in

accordance with the regulations of local authorities regarding flammable items.

CAUTION – Risk of Fire or Explosion due to Flammable Refrigerant Used.

Follow Handling Instructions Carefully in Compliance with U.S. Government Regulations.

WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, just empty

contents and let it defrost itself with the access lid open, use a dry soft towel to dry the inner surfaces before

returning the unit to operating conditions. Do not reload contents until the interior is at the desired

temperature.

WARNING: Do not damage the refrigerant circuit.

Operating, moving, and use of the milk coolers must avoid either damaging the refrigerant tubing, or

increasing the risk of a leak by impacting other objects or attempting to drill into the unit.

CAUTION – Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing; Follow Handling Instructions

Carefully. Flammable Refrigerant Used

Component spare parts shall be replaced with like components parts and servicing shall be done by

authorized service personnel, as to minimize the risk of ignition due to incorrect parts or improper operation.

DANGER: Risk of child entrapment. Before you throw away your old milk cooler:

Take off the door and discard it separately from the appliance body.

Service and Installation Manual

SPECIFICATIONS

MODEL#

V/Hz/Ph

STORAGE

CAPACITY

Cu-ft

CAPACITY

(13”x13”x11”

Crates)

CAPACITY

(19”x13”x11”

Crates)

AMP

DRAW

CHARGE

REFRIGERANT

NEMA

PLUG

MXMC34HC

115/60/1

13.2

1/4

3.17

R290A

5-15P

MXMC49HC

115/60/1

19.6

7.5

1/4

3.17

R290A

5-15P

MXMC58HC

115/60/1

23.5

7.5

1/3

3.17

R290A

5-15P

CONGRATULATIONS ON YOUR NEW COOLER

Note these instructions apply to all milk coolers. Installation of equipment may not exactly correspond to

your model.

INSTALLATION

1. AIR CIRCULATION

-The cooler should be placed in a warm, dry room, with suitable ventilation. Please make sure to avoid any

partition or objects that may stop the air flow. Please make sure there is enough space for air circulation to

the rear of the unit. Recommended space between the rear of the unit to the wall is at least 5 inches.

2. FOUNDATION

- Please make sure that the floor where the unit will be placed can support the total weight plus any other

contents that it may hold.

3. DO NOT PLACE NEAR HEAT

- Please make sure to avoid hot corners and locations near stoves.

- High ambient temperature will significantly reduce cooling efficiency.

4. INDOOR USAGE ONLY

- This unit is designed and tested for indoor use only. Never place the cooler in strong sunlight.

- Outdoor usage will void its warranty.

5. LEVELING

- Please make sure that the unit is level from the front to the back and side to side before placing it in service

6. STABILITY

-The cooler should always be placed on a stable surface with all casters level and the brakes set when in

use or it’s being stored in an accessible location

Service and Installation Manual

ELECTRICAL CONNECTION

The cooler must be connected to a NEMA 5-15 or 5-20 receptacle with the correct voltage/frequency, as

show on the nameplate. The standard for U.S is 115V/60Hz. Voltage variations of ±10% are acceptable.

Greater variations can damage the cooler, and in such cases the factory warranty is not valid. In the case of

extreme voltage variation, above or below the standard, your local supplier or utility company will be able to

advise you, what to do.

All wiring between the electrical panel and the unit must be done in accordance with the National Electric

Code and all state and local codes.

FOOD STORAGE

The cooler is only designed as a serving vehicle and is not suited to store cold food for extended periods of

time. In other words, only milk containers must be placed in the cooler. The cooler must not be filled beyond

the height limit of the included contents fill level line, or in cases where there is no such line, to within

100mm below the lid. This is to ensure the product temperature remains less than 40°F.

OPERATING INSTRUCTIONS

The temperature in the cooler is automatically regulated by a set thermostat.

The position of the cooler, the ambient temperature, the number of times the lid is opened and for how long

the lid is opened are all factors affect the temperature in the cooler. To assur e pr op er t em perat ur e regulation

do not place in the appliance in sunlight or near / adjacent to a heat-radiating surface.

If your cooler is fitted with a lock, the key should be kept out of the reach of children. If your new cooler is to

replace an older one, which is not in use any more, you should remove the lock mechanism on the old one,

before disposing it.

Do not throw items into the storage area. Failure to heed these recommendations could result in damage to

the

interior of the cabinet.

The factory setting for the temperature range is 34°F to 38° F which keeps your milk at a safe,

cold temperature.

CAUTION

Service and Installation Manual

SOLID STATE THERMOSTAT DESCRIPTIONS

1. FRONT PANEL COMMANDS

To dis pl ay t arge t set po int; i n pr ogra mm in g mo de i t sele ct s a pa rame te r or c on fi rms an ope ra tion .

To sta rt a m anua l defr os t

To vie w th e la te st ala rm occ ur renc e; i n pr og ra mm ing mo de i t br ow se s the parameter

codes or increases the display value

To vie w th e la te st ala rm occ ur renc e; i n pr og ra mm ing mo de i t br ow se s th e pa ra mete r

codes or decreases the display value

KEY COMBINATION

To l oc k & un lo ck t he k ey bo ar d

To ent er i n prog ra mming mode

To r et ur n to the r oom te mper at ure di sp la y

1.1 Function of LEDS

2. MAIN FUNCTIONS

2.1 HOW TO SEE THE SETPOINT

1. Push and immediately release the SET key: the display will show the set point value.

2. Push and immediately release the SET key or wait for 5 seconds to display the sensor value again.

2.2 HOW TO CHANGE THE SETPOINT

1. Hold the SET key for more than 2 seconds to change the set point value.

2. The value of the set point will be displayed and the LED starts blinking.

3. To change the set value push the or key within 10s.

4. To set a new point value, push the SET key again or wait 10s.

2.3 HOW TO START A MANUAL DEFFROST

1. Hold the key for more than 2 seconds and the manual defrost will start

2.4 HOW TO LOCK THE KEYBOARD

1. Hold the and keys for more than 3s.

2. The “POF” message will be displayed and the keyboard will be locked. At this point, it will be possible only

to see the set point or the MAX or Min temperature stored.

3. If a key is pressed more than 3s the “POF” message will be displayed.

2.5 HOW TO UNLOCK THE KEYBOARD

Service and Installation Manual

DANGER

Hold the and keys together for more than 3s, till the “POF” message is displayed.

3. ALARM SIGNALS

HOW TO SEE THE ALARM AND

RESET THE RECORDED ALARM

1. Hold the or key to

display the alarm signals.

2. When the signal is displayed, hold

the SET key until the “rst” message

is displayed, and push the SET key

again. The “rst” message starts

blinking and the normal temperature

will be displayed

MAINTENANCE

The power switch must be turned to OFF and the unit disconnected from the

power source whenever performing service, maintenance functions or

cleaning the refrigerated area.

1. CLEANING

1.1 CLEANING STAINLESS STEEL INTERIOR AND EXTERIOR

Damage to stainless steel finish due to improper use of cleaning products or

non-recommended products is NOT covered under this product's warranty.

• Do

- Use warm, soapy water and a soft, clean cloth or sponge

- Rinse surfaces with clean, warm water and dry immediately to avoid water spots

• DO NOT USE

- Abrasive or harsh cleaners

- Ammonia

- Chlorine bleach

- Concentrated detergents or solvents

- Metal or plastic-textured scouring pads

- Vinegar-based products

- Citrus-based cleaners

- Detergents that contain chlorine

Note: It suggested that the unit be emptied daily after all peak demand periods have passed, and

any remaining contents be placed in a storage refrigerator. The unit should be unplugged and

opened to allow it to defrost naturally. Let the unit air dry after cleaning and plug the unit in to

rebuild it frost layer at least 3 hours to loading with product.

1.2 CLEANING THE CONDENSER FINS

-To maintain proper refrigeration performance, the condenser coil must be free of dust, dirt

and grease

-This will require periodic cleaning. Condenser fins should be cleaned at least every month or as

Service and Installation Manual

DANGER

needed

Never use a high-pressure water wash for this cleaning procedure as water can

damage the electrical components located near or at the condenser coil.

MAINTENANCE

1.3 CLEAN THE GASKET

- The door gasket should be cleaned frequently to maintain proper sealing

1.4 CHECK AFTER CLEANING

- Check the unit again for safety

- Check that the unit is operating properly

2. The lid may be cleaned in the same way as the cooler.

3. If a condenser and associated fan are fitted at the back bottom of the cooler, they can gather dust and dirt.

If cleaning is necessary, they should be vacuumed with a soft brush.

4. Please note that the parts behind the protective grill can be hot and rotating.

5. POWER CORD

5.1

- Please make sure that the power cord is connected to the proper voltage

The power cord must be connected to a protected circuit with the correct voltage

and amperage

- Turn ʻoffʼ the power switch before disconnecting the power cord, whenever

performing maintenance functions or cleaning the refrigerated cabinet

- Compressor warranties are void if compressor burns out due to improper voltage

5.2. RE-STARTING

- If disconnected, wait for 5 minutes before re-starting

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Maxx Cold Zubehör Handbücher

Maxx Cold

Maxx Cold MXCR96B Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung