Maytronics Dolphin WAVE 300 XL Bedienungsanleitung

Dolphin WAVE 300 XL

Pool Cleaner

User Manual

8151452 Rev. 02

Dolphin WAVE 300 XL Pool Cleaner |User Manual

Dolphin WAVE 300 XL Pool Cleaner

User Manual

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS..................................................................2

FCC STATEMENT..........................................................................................................3

1. INTRODUCTION ...................................................................................................4

1.1 Speciﬁcations ................................................................................................4

1.2 Water conditions ........................................................................................4

2. UNPACKING YOUR POOL CLEANER .............................................................4

3. ASSEMBLING THE POOL CLEANER ..............................................................5

4. WORKING WITH THE MMI CONSOLE ...........................................................6

4.1 MMI console overview ............................................................................6

4.2 MMI alerts ....................................................................................................7

4.3 MMI functions.............................................................................................7

4.4 WAVE 300 XL parameters..................................................................... 7

4.5 Choosing additional pool proﬁles ......................................................9

5. SETTINGS .............................................................................................................10

6. DAILY OPERATION............................................................................................. 11

6.1 Operating the WAVE 300 XL................................................................. 11

6.2 Using the remote control unit........................................................... 12

6.3 Cleaning the ﬁlter ................................................................................... 13

7. TROUBLESHOOTING ........................................................................................14

Dolphin WAVE 300 XL Pool Cleaner |User Manual

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Take the Robot Pool Cleaner out of the pool before allowing people to enter the pool.

WARNING

When examining the Robot Pool Cleaner, disconnect the main power supply.

WARNING

Ensure that children do not attempt to access Robot Pool Cleaner while it is operating.

WARNING

Keep the Robot Pool Cleaner out of the reach of children or persons with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction.

WARNING

Only an original power cable must be used, at all times. Replaced by a Robot Pool Cleaner

certified technician, in case of need to avoid hazard.

WARNING

The unit must be connected only to a supply circuit that is protected by a ground-fault

circuit interrupter (GFCI). This GFCI should be tested on a routine basis.

To test the GFCI, push the test button. The GFCI should interrupt power.

Push the reset button. Power should be restored. If the GFCI fails to operate in this manner,

the GFCI is defective. If the GFCI interrupts power to the power unit without the test button

being pushed, a ground current may be flowing, indicating the possibility of an electric

shock. Do not use the power unit. Disconnect the power unit and contact the manufacturer

for assistance.

WARNING

To reduce the risk of electric shock replace damaged cord immediately. Do not use

extension cord to connect unit to electric supply; provide a properly located outlet.

Please ensure that the following PRECAUTIONS are implemented:

CAUTION

Only a trained operator should operate the Robot Pool Cleaner.

CAUTION

Operator should keep hands away from driving belt mechanism.

CAUTION

Position the Caddy and power supply at least 3.5 m / 12 ft from pool’s edge – during

operation.

CAUTION

For continued protection against possible electric shock, the power supply unit should be

placed at least 11cm / 4’’ above ground.

READ AND FOLLOW ALL INSTRUCTIONS.

Please adhere strictly to the following WARNINGS:

Dolphin WAVE 300 XL Pool Cleaner |User Manual

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance (Maytronics Ltd.) could void the user’s authority to operate the equipment.

CAUTION

When lifting the Robot Pool Cleaner, take care to prevent back injury.

CAUTION

Do not bury cord – locate cord to minimize abuse from lawn mowers, hedge trimmers and

other equipment.

CAUTION

This Robot is for use with permanently installed pools. Do not use with storable pools.

A permanently installed pool is constructed in or on the ground or in building such that it

cannot be readily disassembled for storage and reassembled to its original integrity.

SAVE THESE INSTRUCTIONS

Dolphin WAVE 300 XL Pool Cleaner |User Manual

1. INTRODUCTION

This user guide describes how to operate your WAVE 300 XL Robot Pool Cleaner and how to use

the pool cleaner’s Maytronics Machine Interactive (MMI) console. The interactive, state-of-the-art

MMI control console Provides full control of the robot and enables you to conﬁgure the cycle time,

operation delay, and cleaning scan. It also enables you to diagnose various technical functions and

parameters. The console houses a remote control unit for manual operation and for temporarily

overriding the automatic cleaning operations.

The WAVE 300 XL is designed to handle four dierent swimming pool conﬁgurations that are set by

your Maytronics dealer, and stored in the MMI’s memory.

The robot is preset at the factory with speciﬁc default pool settings that can be reset.

1.1 Speciﬁcations

• Motor protection: IP 68

• Minimum depth: 0.40 m / 1.3 ft

• Maximum depth: 7 m / 22.96 ft

1.2 Water Conditions

Use the Pool Cleaner in the following water conditions only:

• Chlorine: Max 4 ppm

• pH: 7.0 - 7.8

• Temperature: 6°-35°C / 43°-95°F

• NaCl: Maximum = 5000 ppm

2. UNPACKING YOUR POOL CLEANER

Before you start the assembly process, carefully remove all the items from the shipping box and check

them against the packing list.

The box should contain:

• Documentation and accessories

• Un-assembled Caddy for storing and carrying the WAVE 300 XL

• MMI console (includes remote control unit) assembled to the Caddy's handle

• WAVE 300 XL and floating cable rolled on the Cable roller

• Power supply unit assembled to the Caddy base

• Filter Bags:

2 ﬁne porosity ﬁlter bags assembled in the Dolphin WAVE 300 XL robot for day-to-day cleaning

2 ultra-ﬁne ﬁlter bags for ﬁne dust particles

2 loose weave ﬁlter bags for rough debris

Power supply

• Input: 100-250 AC Volts

• 50-60 Hertz

• Output: <43 VDC

• IP 54

Dolphin WAVE 300 XL Pool Cleaner |User Manual

3. ASSEMBLING THE POOL CLEANER

This section describes how to assemble your pool cleaner.

To assemble the Dolphin WAVE 300 XL Pool Cleaner:

1. Attach the Caddy handle to the Caddy base and fasten with the four screws and four nuts provided.

2. Attach the cable roller in its designated place, and fasten with two screws.

3. Connect the MMI communications cable to the power supply unit.

4. Connect the connection cable between the power supply and the cable roller.

Figure 1: Assembling the Dolphin WAVE 300 XL - 1

Figure 2: Assembling the Dolphin WAVE 300 XL - 2

MMI

MMI remote control unit

Cable

roller handle

MMI

communication

cable

Power supply

Main power supply cable

Four screws

MMI

Cable roller

Floating cable

Caddy handle

Top cover

Caddy base

Connection cable

between power supply

and cable roller

Two screws

Dolphin WAVE 300 XL Pool Cleaner |User Manual

4. WORKING WITH THE MMI CONSOLE

This chapter describes how to work with the MMI console and includes the following sections:

• MMI Console Overview, page 6

• MMI Alerts, page 7

• MMI Functions, page 7

• WAVE 300 XL Parameters, page 7

• Choosing Additional Pool Profiles, page 9

4.1 MMI Console Overview

The interactive MMI control console provides easy access to the robot’s settings, functionality,

and LED indicators.

• In this user manual, the term Press Start means to simultaneously press both green buttons on

the MMI console (marked 2and 3in the Figure 4).

• The MMI is equipped with a screensaver that is displayed after 5 minutes of idle time. Press the

POOL and HOME buttons (marked 5and 6in Figure 4) to exit the screensaver mode.

• Some options in the MMI (pool profile setup) menus are blocked with a code to prevent changing

the setting accidentally. The code sequence for unblocking these options is: 3, 2, and 1(Figure 4).

Figure 4: MMI Console

Roller inner connection

Figure 3: Roller Inner Connection

Dolphin WAVE 300 XL Pool Cleaner |User Manual

4.2 MMI Alerts

The WAVE 300 XL has the following alert LEDs:

• Filter: This Filter LED lights up when the filter is full and needs to be cleaned at the end of the

cleaning cycle. If this LED lights up mid-cycle, you do not need to immediately stop the operation;

you can wait until the cycle is completed. This LED indicator automatically resets when the robot

starts a new cycle with a clean filter.

• Alert: This Alert LED lights up to indicate an error that stops the robot from functioning. In such

cases, inspect the robot to locate the problem and if it can be fixed, start the robot again. If the

error repeats itself, then details of the specific error are displayed on the MMI screen (Figure 4).

If this occurs, contact your Maytronics dealer immediately.

4.3 MMI Functions

The following functions are available on the MMI console.

Command

Description

From the Wave 300 XL screen, press Menu to access the Main Menu screen



Scroll up



Scroll down

Start 

Press both green buttons simultaneously to start pool cleaning

Select

Press Select to conﬁrm your selection after using the scrolling buttons

Modify

Press Modify to change settings after making a selection

Back

Press Back to return to the previous screen

Exit

Press Exit to return to the Wave 300 XL screen

4.4 WAVE 300 XL Parameters

You can view and edit many of the WAVE 300 XL parameters from the MMI Main Menu screen.

To view the WAVE 300 XL parameters:

1. Switch on the power supply. The Wave 300 XL screen is displayed in the MMI.

2. Press Menu to access the Main Menu screen.

Select Exit

Main Menu

Pool Profile

Filter State Clean

Technician Mode

Statistics

Dolphin WAVE 300 XL Pool Cleaner |User Manual

The following parameters are available on the ﬁrst Main Menu screen:

Parameter

Description

Pool Profile

Press the down arrow



or up arrow



, to highlight Pool Proﬁle, and press

Select to access the Pool Proﬁle screen. The Pool Proﬁle screen displays the four

dierent conﬁgured Pool Proﬁles.

Note: The WAVE 300 XL is delivered with a default pool proﬁle parameter.

To change the pool proﬁle parameter, see Choosing Additional Pool Proﬁles on

page 9.

Filter State

Reports on the ﬁlter’s condition:

• Clean: Filter is ready for use.

• Full: Clean ﬁlter.

The ﬁlter warning light on the console also indicates when the ﬁlter needs

cleaning.

Technician

Mode

Press the down arrow



or up arrow



, to highlight Technician Mode, and press

Select to enter the technician screen with restricted access.

Statistics

Press the down arrow



or up arrow



, to highlight Statistics, and press Select

to review data on usage.

3. There are two Main Menu screens. To access the second screen, press the scroll down arrow



The following additional parameters are available on the second Main Menu screen:

Parameter

Description

Clock Setup Press the down arrow



or up arrow



, to highlight Clock Setup, and press

Select to access the Clock Setup screen and 12/24-hour mode.

Date Setup Press the down arrow



or up arrow



, to highlight Date Setup, and press

Select to access the Date setup screen.

Error Report Press the down arrow



or up arrow



, to highlight Error Report, and press

Select to display information for service technicians.

Language Press the down arrow



or up arrow



, to highlight Language, and press

Select to enter the Language interface mode.

Note: To return to English from any other language, press and hold the Menu button on the

Wave 300 XL screen for 3-4 seconds.

Select Exit

Main Menu

Clock Setup

Date Setup

Error Report

Language English

Dolphin WAVE 300 XL Pool Cleaner |User Manual

4.5 Choosing Additional Pool Proﬁles

The WAVE 300 XL can be conﬁgured for four dierent pool proﬁles by your dealer. The conﬁgured

settings are stored in the MMI’s memory. This section describes how to choose additional pool

settings.

To add a new pool conﬁguration:

1. Go to the Wave 300 XL screen. Pool A is displayed as the currently deﬁned setting.

2. Press Pool A to access the Pool Proﬁle screen. The Pool Proﬁle screen is displayed.

3. Choose a dierent pool proﬁle (Pool B, Pool C, or Pool D) and press Select. The selected pool proﬁle

appears.

Menu Start Pool A

Select Exit

Pool A

Pool B

Pool C

Pool D

Select Pool

Andere Handbücher für Dolphin WAVE 300 XL

Inhaltsverzeichnis

Andere Maytronics Schwimmbadroboter Handbücher

Maytronics

Maytronics Dolphin W 20 Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave Bedienungsanleitung

Maytronics

Maytronics Dolphin X40 Plus Bedienungsanleitung

Maytronics

Maytronics Dolphin SX20 Bedienungsanleitung

Maytronics

Maytronics Dolphin C5 Bedienungsanleitung

Maytronics

Maytronics MTC6 DELUXE 5 Bedienungsanleitung

Maytronics

Maytronics Dolphin Active Classic Bedienungsanleitung

Maytronics

Maytronics Dolphin Basic 4-UNI Bedienungsanleitung

Maytronics

Maytronics Dolphin Nautilus CC Bedienungsanleitung

Maytronics

Maytronics Dolphin COMM. 12 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave 30 Bedienungsanleitung

Maytronics

Maytronics Dolphin DX35 Bedienungsanleitung

Maytronics

Maytronics Dolphin M600 Bedienungsanleitung

Maytronics

Maytronics Dolphin M400 Bedienungsanleitung

Maytronics

Maytronics Swash CLX Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty 200 Bedienungsanleitung

Maytronics

Maytronics Dolphin Basic 13 Bedienungsanleitung

Maytronics

Maytronics MCC5 Bedienungsanleitung

Maytronics

Maytronics Dolphin Classic 13 Bedienungsanleitung

Maytronics

Maytronics Dolphin Supreme M5 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave Bedienungsanleitung

Maytronics

Maytronics Hybrid Bedienungsanleitung

Maytronics

Maytronics MTC8-UNI Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung