Megger AVO210 Bedienungsanleitung
2
G SAFETY INFORMATION
Understand and follow operating instructions carefully.
GWARNING
■Do not use test leads or the multimeter if they are damaged
■Do not use the multimeter if the tester is not operating properly
■To reduce risk of fire and shock do not expose this product to rain or
any moisture
■When using test leads or probes, keep fingers behind the finger guards.
■Remove test leads from meter before opening the battery door or meter
case.
■Use the meter only as specified in this manual or the protection by the
meter might be impaired.
■Always use proper terminals, switch position, and range for measurements.
■Never attempt a voltage measurement with the test lead inserted into the
A input terminal.
■Verify the meter’s operation by measuring a known voltage. If in doubt,
have the meter serviced.
■Do not apply more than the rated voltage, as marked on meter, between
terminals or between any terminal and earth ground.
■Do not attempt a current measurement when the open voltage is above the
fuse protection rating.
■Suspected open circuit voltage can be checked with voltage function.
■Only replace the blown fuse with the proper rating as specified in this
manual.
■Use caution with voltages above 30 Vac rms, 42 Vac peak , or 60 Vdc.
These voltages pose a shock hazard.
■To avoid false readings that can lead to electric shock and injury, replace
battery as soon as low battery indicator appears.
■Disconnect circuit power and discharge all high voltage capacitors before
testing resistance, continuity, diodes, or capacitance.
■Do not use meter around explosive gas or vapour.
3
GCAUTION
■Disconnect the test leads from the test points before changing the position
of the function rotary switch.
■Never connect a source of voltage with the function rotary switch
W, , d,a,A, bposition.
■Do not expose Meter to extremes in temperature or high humidity.
■Never set the meter in daA function to measure the voltage of a
power supply circuit in equipment that could result in damage the meter
and the equipment under test.
Symbols as marked on the meter and instruction card
FRisk of electric shock
GSee instruction card
dDC measurement
tEquipment protected by double or reinforced insulation
Battery
aAC measurement
cConforms to EU directives
Maintenance
Do not attempt to repair this Meter. It contains no user-serviceable parts. Repair or
servicing should only be performed by qualified personnel.
Cleaning
Periodically wipe the case with a dry cloth and detergent. Do not use abrasives or
solvents.
4
AC / DC Voltage and Frequency
Continuity and Diode
5
Resistance and Capacitance
Note – To improve the measurement accuracy of small value capacitor, record the
reading with the test leads open, then subtract the residual capacitance of the meter
and leads from measurement.
CUNKNOWN = CMEASUREMENT - CRESIDUAL
MIN MAX Record
6
DC / AC Current
Display Hold
7
Manual Ranging and Auto Ranging
Auto Power Off (Battery Saver)
8
Disable Auto Power Off
Test Equipment Depot - 800.517.8431
99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
9
Non-Contact Voltage Alert (VOLTSENSE)
1. Volt sense switch will be activated on any function or at OFF status.
2. Test leads are not used for the Volt sense test.
3. Press the Volt sense button. The display will blank out, a tone sounds
and the red LED lights up to verify the instrument is operational. The
Volt sense button must be held down to detect the presence of voltage
without use of the leads.
4. If a voltage of 50V to 600V (50 to 500Hz) is detected near the top of
meter a continuous tone sounds and the red LED near the top of meter
illuminates.
10
Fuse Replacement
Refer to the following diagram to replace fuse.
GUse only a fuse with the amperage, interrupt, voltage,
and speed rating specified.
˙ Fuse rating: 10A, 500V
Inhaltsverzeichnis
Andere Megger Messgerät Handbücher
Megger
Megger DCM305E Bedienungsanleitung
Megger
Megger DET10C Bedienungsanleitung
Megger
Megger MOM2 Win Bedienungsanleitung
Megger
Megger DLRO100EB Bedienungsanleitung
Megger
Megger S1-1054/2 Bedienungsanleitung
Megger
Megger DCM320 Bedienungsanleitung
Megger
Megger DCM330 Bedienungsanleitung
Megger
Megger DLRO Bedienungsanleitung
Megger
Megger DCM340 Bedienungsanleitung
Megger
Megger SmartFuse 250 Bedienungsanleitung
Megger
Megger BERT-20E1 Bedienungsanleitung
Megger
Megger 1006-603 Bedienungsanleitung
Megger
Megger DET14C Bedienungsanleitung
Megger
Megger DCM305E Bedienungsanleitung
Megger
Megger MCCV6000-18 Bedienungsanleitung
Megger
Megger TDR2000 Bedienungsanleitung
Megger
Megger EGIL200 Series Bedienungsanleitung
Megger
Megger PCA2 Bedienungsanleitung
Megger
Megger Fault Sniffer 2 Bedienungsanleitung
Megger
Megger PVM210 Bedienungsanleitung
