Megger MEG10-01 Bedienungsanleitung

Line Input

(under cover)

RS232 port

(under cover)

Polarisation Index

Insulation Resistance

Polarisation Index

Insulation Resistance

Power

On/Off

LED

Red - HT On

Green - Charging Battery

Voltage

Indicator

Voltage at

Terminals

Voltage at

Terminals

Digital Display

Recording Timer ON

Time

Indicator

Analogue

Display

Test

Start/Stop

Display

Scroll

Test Voltage

increase/

decrease

Test Duration

increase/

decrease

MEG10-01 10kV

Insulation tester Quick Start

Measurement Terminals

-ve, Guard, +ve

GSAFETY WARNINGS

■This instrument must only be used by suitably trained and competent persons.

■The circuit under test must be switched off, de-energised and isolated before insulation test connections are

made.

■Circuit connections must not be touched during an insulation test.

■After completion of an insulation test, capacitive circuits must be discharged before disconnecting the test

leads.

■Turning the instrument off, and manually discharging of circuits on completion of tests is recommended as

standard procedure, before touching the test leads.

■In certain circumstances, breakdown of the circuit under test may cause the instrument to terminate the test

in an uncontrolled manner, possibly causing a loss of display while the circuit remains energised. In this

event, it is even more important that the ‘ON/OFF’ key is pressed, and the circuit manually discharged

before touching any connections.

■Test leads, including crocodile clips, must be in good order, clean and with no broken or cracked insulation.

■The instrument should not be used if any part of it is damaged.

■Water on the surface of the instrument may lead to erroneous results. It is recommended that the instrument

is not used in wet weather conditions.

■This instrument is not intrinsically safe and must not be used in hazardous atmospheres.

SIMPLE OPERATION GUIDE

1. To charge the batteries, ensure the instrument is

powered off and connect the line input to a 100

- 240 V (±10%), 47 - 63 Hz power supply.

2. The instrument may be operated from charged

internal batteries, or an external supply, as

above, by powering the instrument on.

Charging will be discontinued.

3. Set the Test Type to Polarisation Index (PI

indicated) or Insulation Resistance (no

indication).

4. Set the Test Voltage as required. 500, 1000,

2500, 5000 and 10000 V are available. Press

both Test Voltage increase/decrease

simultaneously pressing the buttons at any time

during a test will display the pre-set test

duration.

5. Set the Test Duration to zero (manual

termination) or a period between 10 seconds

and 99 minutes 59 seconds by pressing the

Time increase or Time decrease buttons.

Selected duration is displayed. Pressing both

Test Duration increase/decrease

buttons simultaneously pressing the buttons at

any time during a test will display the pre-set

test duration.

6. Press and hold Test Start/Stop button until test

starts (approximately 2 seconds).

7. Press Test Start/Stop button to end the test, or

wait until the set duration has elapsed, when

the test will stop automatically.

8. Press ‘Display scroll’ to scroll through the

results display. The details available will depend

on the type of test previously performed.

For details of recording, downloading or deleting

test data see the full User Guide which is contained

on the accompanying CD.

Megger Limited

Archcliffe Road

Dover, CT 17 9EN

England

Part No. 6172-765 V01 Printed in England 10HH

www.megger.com

Andere Handbücher für MEG10-01

Andere Megger Prüfgeräte Handbücher

Megger

Megger MWA3 Series Bedienungsanleitung

Megger

Megger MIT400/2 Series Bedienungsanleitung

Megger

Megger S1-568 Bedienungsanleitung

Megger

Megger MIT300 Bedienungsanleitung

Megger

Megger LT300 Bedienungsanleitung

Megger

Megger SMART THUMP ST25-30 Bedienungsanleitung

Megger

Megger VLF Sinus 62 kV Bedienungsanleitung

Megger

Megger BM25 Bedienungsanleitung

Megger

Megger STX 40 Bedienungsanleitung

Megger

Megger PAT150-DE Bedienungsanleitung

Megger

Megger BM5200 Bedienungsanleitung

Megger

Megger SPG 5-1000 Bedienungsanleitung

Megger

Megger PFL40A Bedienungsanleitung

Megger

Megger MFT1700 series Bedienungsanleitung

Megger

Megger T 99/1 Bedienungsanleitung

Megger

Megger Vidar Bedienungsanleitung

Megger

Megger Baker AWA-IV Bedienungsanleitung

Megger

Megger SVERKER 750 Bedienungsanleitung

Megger

Megger 210170 Bedienungsanleitung

Megger

Megger MET1000-DE Bedienungsanleitung

Megger

Megger S1-5010 Bedienungsanleitung

Megger

Megger Vidar Bedienungsanleitung

Megger

Megger SPG 32-1750 Bedienungsanleitung

Megger

Megger VLF SIN-45 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung