Mercia Garden Products 03DTSHRA0808FGC42TW-V1 Gebrauchsanweisung

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03DTSHRA0808FGC42TW-V1

DIP TREATED SHIPLAP REVERSE APEX 8X8 FULLY GLAZED CONCERTINA 4, 2 TALL

WINDOWS- SUMMER HOUSE

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

Please retain product label and instructions for future reference

General Instructions

P 1

P 2

03DTSHRA0808FGC42TW-V1

Please retain product label and instructions for future reference

134

11 Ridge Bar - 28x28x2304mm

FS2828-2304mm

13 Cover Trim - 12x40x2043mm QTY 7

S1240-2043mm

Fascia - 12x60x1333mm QTY 4

S1260-1333mm

15 Door Strip - 12x60x1720mm QTY 2

S1260-1720mm

16 Door Support Framing - 27x44x2304mm QTY 1

F2744-2304mm

Finial QTY 2

SHED DIAMOND FINIAL

Rain Guard - 28x44x680mm QTY 2

RG2844-680mm

19 20

Butt Hinge QTY 14

PI-07-0066

Door Handle QTY 2

PI-07-0081

Barrel Bolt QTY 6

PI-07-0114

Turn Button QTY 2

PI-07-0034

Press Lock

PI-07-0162

“L” Bracket QTY 2

PI-07-0012

Felt

PI-01-0016

17 Panel Framing - 28x28x1180mm QTY 4

FS2828-1180mm

12 Floor Block - 28x28x400mm QTY 8

F2828-400mm

Floor QTY 4

AI-R11MBF1175X1175-V1

Roof Sheet QTY 2

AI-S11MBOHAR2390X1356-V1

Door Panel QTY 1

AI-03S11SHFCD2360X2015-V1

Window Panel QTY 2

AI-03S11SH1TFWC687X2007-V1

Side Panel QTY 2

AI-S11SHPPTOV1623X2007-V1

Back Panel QTY 2

AI-S11SHPP1180X2015-V1

Gable Top QTY 2

AI-S11SHAGT2310X559-V1

Master Door QTY 1

AI-STDFGMD475X1715-V1

Secondary Door QTY 1

AI-STDFGSD475X1715-V1

Plain Door QTY 2

AI-STDFGPD475X1715-V1

Overall Dimensions:

Width = 2438mm

Depth = 2488mm

Height = 2670mm

Base Dimensions:

Width = 2350mm

Depth = 2350mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

P 3

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

35mm Bolt QTY 4

50mm Screws QTY 91

40mm Screws QTY 30

30mm Screws QTY 79

25mm Screws QTY 78

10mm Screws QTY 36

Felt Tacks QTY 110

60mm Screws QTY 16

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Pre drill

hole

25mm

screw

30mm

screw

Lay the Door Panel (No.1) on a at

surface framing facing upwards. Attach

the plain doors (No.10) to the inside

framing of the door panel (No.1) using

3x butt hinges (No.19).

*Fix the hinges to the inside of the door

panel.

Fix to the door using 3x25mm screws &

3x30mm screws to the framing per

hinge, ensure the doors open freely,

folding back into the building unrestrict-

ed.

18x25mm Screws

18x30mm Screws

Step 1

Parts Needed - No.1 QTY 1

- No.10 QTY 2

- No.19 QTY 6

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

25mm

screw

19 19

Turn the door panel (No.1) over so the

framing is on the at surface. Fix the

master (No.8) and secondary door

(No.9) to the attached plain doors

with butt hinges (No.19) , using

6x25mm screws per hinge.

*Ensure the doors open freely,

folding back into the building

unrestricted.

48x25mm Screws

Step 2

Parts Needed - No.8 QTY 1

- No.9 QTY 1

- No.19 QTY 8

IMPORTANT: Pre-drill before xing screws.

Internal

External

P 4

Please retain product label and instructions for future reference

Step 3

Parts Needed - No.20 QTY 2

- No.21 QTY 6

- No.24 QTY 1

35mm

bolt

Pre drill

hole

10mm

screw

25mm

screw

Secure the barrel bolts (No.21) to the top &

bottom of each side door and the secondary door

using 6x10mm screws.

Attach the press lock (No.24) to the master door

with 4x25mm screws, aligning the barrel with the

key hole.

*Ensure the key turns and locks properly before

xing to the door.

Fix the door handles (No.20) to the outside of the

master and secondary door using the 35mm bolts

provided.

36x10mm Screws

4x25mm Screws

4x35mm Bolts

IMPORTANT: Pre-drill before xing screws.

Fix the Window Panel (No.7) and

Side Panel (No.3) together by

screwing through the framing

using 6x50mm screws.

Ensure to stagger screws to avoid

colliding.

Repeat this with the second

Window and Side panel but the

opposite way round, as shown in

the diagram.

12x50mm Screws

Pre drill

hole

50mm

screw

Step 4

Parts Needed - No.3 QTY 2

- No.7 QTY 2

IMPORTANT: Pre-drill before xing screws.

Secure the oor (No. 6) to the

Floor Blocks (No.12) using 8x30mm

screws per oor.

Repeat this for one other oor panel

16x30mm Screws

Pre drill

hole

30mm

screw

Step 5

Parts Needed - No.6 QTY 2

- No.12 QTY 8

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Step 6

Parts Needed - No.6 QTY 2

Secure the oor (No. 6) to the

assembly from Step 5, using 8x30mm

screws per oor.

Repeat this to create two assembled oors

16x30mm Screws

IMPORTANT: Pre-drill before xing screws.

P 5

Please retain product label and instructions for future reference

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Place the assembled oor panels

(No.6) upside down onto a rm and

level base. Ensure the base has suitable

drainage, free from areas where stand-

ing water can collect.

Secure the oors together using

8x50mm screws through the oor

bearers in an alternating pattern.

Once xed together turn the oor back

the right way up.

8x50mm Screws

Step 7 IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Fix the Back panels (No.4) side by

side using 3x50mm screws, x the

corners or the back panel (No.4)

and the Side Panel (No.3)

Do not secure the building to the

oor until the roof tted.

6x50mm Screws

Step 8

Parts Needed - No.3 QTY 1

- No.4 QTY 2

- No.7 QTY 1

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Fix the side panels (No. 3 and

No.7) and the door panels (No.1)

corners with 50mm screws as

shown in the illustration.

Do not secure the building to the

oor until the roof tted.

9x50mm Screws

Step 9

Parts Needed - No.1 QTY 1

- No.3 QTY 1

- No.7 QTY 1

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Place the gable tops (No.5) onto the

window panels, ensuring the boards

interlock.

Secure in place using 4x50mm screws

per gable top (No.5), screwing in an

alternating pattern.

8x50mm Screws

Step 10

Parts Needed - No.5 QTY 2

- 5

IMPORTANT: Pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Pre drill

hole

25mm

screw

Attach the “L” brackets (No.25) to

each end of the ridge bar (No.11)

with 2x25mm screws per bracket.

*Ensure the brackets are ush with

the ends of the ridge bar.

Align the ridge bar (No.11) between

the gables and secure to the central

uprights with 2x25mm screws per

bracket (No.25) as shown in the

illustration.

8x25mm Screws

Step 11

Parts Needed - No.11 QTY 1

- No.25 QTY 2

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Step 12

Parts Needed - No.17 QTY 4

Place the panel framing (No.17) along

the top of the panels at the front and

back of the building and secure using

2x50mm screws per framing piece.

8x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Step 13

Parts needed - No 2 QTY 2

60mm

screw

Pre drill

hole

Place the Roof Panel (No. 2) on top of the build-

ing making sure the framing in the roof panels

sits rmly within the Gables (No. 5) and on top of

the Ridge Bar (No. 11).

**Make sure that you have got the roof panels

the correct way round with the recess at the

top of the apex as shown in the diagram.**

From the top, x directly through the roof panels

(No. 2) into the ridge bar (No. 11) below using

5x60mm screws per roof panel.

It is essential that the ridge bar (No. 11) and roof

panels (No. 2) framing pull together when xed

with 60mm screws. You may require another

person pushing the ridge bar (No. 11) up from

below to achieve this.

HINT - Follow the nailing line of the framing on

the roof panel so that you are more likely to x

into the ridge bar below.

10x60mm Screws

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

Pre drill

hole

Step 14

IMPORTANT: Pre-drill before xing screws.

40mm

screw

Use 40mm screws to x the roof (No. 2)

down the sides, front and back of the

building.

Be sure that the screws attach into the

framing below.

18x40mm Screws

Pre drill

hole

50mm

screw

Secure the building internally to

the oor using 9x50mm screws

each side.

*Ensure to screw through the

framing into the oor bearers.

36x50mm Screws

Step 15 IMPORTANT: Pre-drill before xing screws.

HANDLE

WITH CARE

Felt

tacks

Cut the felt (No.26) into 3 strips of

2500mm length and place onto the roof,

as shown in the illustration.

*Ensure there is approximately 50mm

overhang of felt around all sides of the

building.

Fix into place using 110x felt tacks at

100mm intervals.

110x Felt Tacks

Step 16

Parts Needed - No.26 QTY 1

Please retain product label and instructions for future reference

P 8

Pre drill

hole

30mm

screw

Screw the cover trims (No.13)

to each corner of the building

and across the joins of the

panels with 3x30mm screws

per trim.

21x30mm Screws

Step 17

Parts Needed - No.13 QTY 7

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

40mm

screw

Attach the fascia’s (No.14) and

nial’s (No.18) to the the sides

of the building using 12x40mm

screws.

12x40mm Screws

Step 18

Parts Needed - No.14 QTY 4

- No.18 QTY 2

IMPORTANT: Pre-drill before xing screws.

Place the Door support bar (No. 16)

to the inside of the door panel as

displayed on the pictures. The

44mm side of the framing should

sit against the inside of the door

panel.

This framing will meet at each side

panel as show in the image, and

should be level with the door panel

framing.

Secure the framing using 4x60mm

screws externally through the front

panel, and a futher 2x60mm screws

through the side panels and into

either end of the framing.

6x60mm Screws

Step 19

Parts Needed - No.16 QTY 1

Pre drill

hole

60mm

screw

IMPORTANT: Pre-drill before xing screws.

Drill 3x6mm holes into the framing in

line with the barrel bolts, these will

act as the catch for the barrell bolts.

*You will need to unsecure the barrell

bolts at this point.

Step 20

P 9

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Fix the rain guards (No.23) above

each window, securing in place

using 2x50mm screws per guard,

ensuring to screw through the

framing.

4x50mm Screws

Step 21

Parts Needed - No.23 QTY 2

IMPORTANT: Pre-drill before xing screws.

30mm

screw

Pre drill

hole

Secondary Door

Locking Door

Attach the two turn buttons (No.22) to the

secondary door at the top and bottom using

2x30mm screws.

*These turn buttons help to keep your doors

straight during high & low levels of moisture

content in the air.

2x30mm Screws

Step 22

Parts Needed - No.22 QTY 2

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

15 15

Attach a strip (No.15) to the hinged side of

the Master and Secondary doors. Each strip

should overlap onto the plain doors to ensure

the gap is covered.

*These strips allow you to adjust the doors

allowing for moisture absorption and

reduction.

6x30mm Screws

Step 23

Parts Needed - No.15 QTY 2

IMPORTANT: Pre-drill before xing screws.

Please be aware you may need to adjust the doors once the building is fully constructed.

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

P 10

Please retain product label and instructions for future reference

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

SILICONE

SEALANT

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 06LOG002-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619RANE3503FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01JER0806-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V2-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHDB0606SFD5W-V1-PEFC Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG171SG-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644RANE4535FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO1208DD-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTDRK0806-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0305SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1006DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung