Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

P 1

01COMGRN0406-V1 - 4x6 Greenhouse Shed

8x6 Greenhouse with shed.

10x6 Greenhouse with shed.

12x6 Greenhouse with shed.

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of

heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also

occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be

avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended

periods of warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guaran-

tee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The

cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of

childrens products independently tested to EN71 level, we cannot accept responsibility for your safety

whilst erecting or using this product.

Refer to the instructions pages for you specic product code

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 2

01COMGRN0406-V1: Plus 8x6, 10x6 & 12x6 Greenhouse with shed.

4x6 Shed

Overall Dimensions:

Width = 1972mm

Depth = 1299mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 1190mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

8x6 Greenhouse with shed

Overall Dimensions:

Width = 1972mm

Depth = 2447mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 2397mm

10x6 Greenhouse with shed

Overall Dimensions:

Width = 1972mm

Depth = 3030mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 2980mm

12x6 Greenhouse with shed

Overall Dimensions:

Width = 1972mm

Depth = 3615mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 3560mm

Door Gable

AI-01COMGRNDG1808X1987-V1

Plain Side QTY 2

AI-01COMGRNPS1193X1543-V1

Plain Gable

AI-01COMGRNPG1808X1987-V1

Floor

AI-01COMGRNF1190X1860-V1

Roof QTY 2

PI-03-0347

Door

AI-01-21ZB544X1660-V1

Ridge Bar - 28x28x1138mm

FS2828-1138mm

Eaves Frame - 28x28x1217mm QTY 2

FS2828-1217mm

Cover Strip - 40x12x1566mm QTY 6

S1240-1566mm

Fascia - 60x12x1053mm QTY 4

S1260-1053mm

Greenhouse Roof Frame - 44x27x1574mm QTY 2

F2744-1594mm (Angled) - Used only when attaching greenhouse to shed (See Step 17).

Greenhouse Roof Block - 44x27x410mm

F2744-450mm (Angled) - Used only when attaching greenhouse to shed (See Step 18).

T-Hinge QTY 3

PI-07-0021

“L” Bracket QTY 2

PI-07-0012

Pad Bolt

PI-07-0035

**For greenhouse contents please see instructions before beginning assembly.**

Nail Bag

50mm Screws - 42

40mm Screws - 28

30mm Screws - 60

20mm Screws - 6

Felt Tacks - 60

Pre Assembly

Before beginning assembly remove the transport

blocks from the bottom of each panel.

Shed Diamond Finial

70mm Screws - 10

Step 1

Place the door (No. 6) into the

door gable (No. 1) aperture,

making sure there is an equal

amount of space either side

of the door.

Once in place secure the door

to the door gable using 3x

T-hinges (No. 12) securing

each hinge into position with

7x30mm screws.

21x30mm screws.

Pre drill

hole

30mm

screw

P 3

Please retain product label and instructions for future reference

Step 3

Place the plain gable (No.3)

and one of the plain panels

(No.2) on to the oor and x

the corners together using

3x50mm screws.

Do not secure the building to

the oor until the roof is

secured in place.

*Ensure the plain gable is tted on

the inside of the plain panel. Screw

through the plain gable framing

into the framing of the plain panel.

3x50mm screws

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Step 2

Place the oor (No. 4) onto a

rm and level surface.

Ensure your base has suitable

drainage and is free from

areas where standing water

can collect.

Step 4

Following the same method

outlined in Step 3 place the

second plain panel and

assembled door gable onto

the oor and x at each corner

using 50mm screws.

Do not secure the building to

the oor until the roof is

secured in place.

9x50mm screws

Step 5

Fix the 2x “L” brackets (No. 13) to

either end of the ridge bar (No. 7)

using 2x20mm screws per bracket.

*Ensure the bracket plate(s) are

ush with each end of the ridge

bar.

Once in place position the ridge bar

between the gables, securing into

position using 2x30mm screws per

side.

4x20mm Screws

4x30mm Screws

Pre drill

hole

20mm

screw

30mm

screw

713

P 4

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 7

Once the roof has been xed

into place secure the

building to the oor using

20x50mm screws.

*Ensure to screw through the panel

framing into the oor bearers

below.

20x50mm screws

Step 6

Attach an eaves frame (No. 8) to one

edge of each roof sheet (No. 5) using

4x30mm screws per roof.

Fix each roof onto the building with

16x30mm screws per roof, making

sure the sheets meet at the apex.

40x30mm Screws

Pre drill

hole

30mm

screw 5

Step 8

Place a cover trim (No. 9)

at each corner of the

building & x into position

using 3x30mm screws per

strip.

12x30mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

30mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

HANDLE

WITH CARE

Felt

tacks

P 5

Please retain product label and instructions for future reference

Felt Size: 1317mm

**Please note: For greenhouse contents please see instructions before beginning assembly.

Not every panel from the greenhouse will be used**

Step 9

Cut the felt into three strips and lay

onto the as shown in the illustration.

*Ensure there is approximatley

50mm of overhanging felt around

the building.

Fix the felt into place using felt tacks

at 100mm intervals.

60x Felt Tacks

Step 10

**If attaching a greenhouse move onto

Step 11.**

Secure the fascia’s (No. 10) and the nial’s

(No. 15) to the front and rear of the building

using 40mm screws.

*Ensure to trap the felt between the

fascia(s) and the building.

16x40mm Screws

Pre drill

hole

30mm

screw

P 6

1862mm

Please retain product label and instructions for future reference

Window panel sizes:

4x6 Greenhouse = 1193mm

(8x6 Greenhouse with shed)

6x6 Greenhouse = 1776mm

(10x6 Greenhouse with shed)

8x6 Greenhouse = 2359mm

(12x6 Greenhouse with shed)

6x6 Greenhouse

(10x6 Greenhouse with shed)

8x6 Greenhouse

(12x6 Greenhouse with shed)

4x6 Greenhouse *Shown

(8x6 Greenhouse with shed)

Step 11 (internal)

Lay the base frame(s) onto the

base as shown in the illustration.

*Ensure your framing is square

and is placed against the front

of the shed.

Secure the base frames together

at each corner using 8x70mm

screws - See greenhouse nail

bag.

8x70mm Screws

Pre drill

hole

70mm

screw

Step 12 (internal)

Place the two window panel(s)

onto the base frame (See Step

11) against the shed and x

into position using 50mm screws.

Ensure to screw through the

panel(s) into the framing

underneath - See greenhouse

nail bag.

See greenhouse instructions

for screw quantities.

Pre drill

hole

50mm

screw

**Please note: This product can be be erected with the shed door either inside the building (internal) or

outside (external). Before beginning assembling, decide which conguration best suits your needs and

read through both sets of instructions carefully.**

Instructions: Internal shed door option.

30mm

16mm

Please retain product label and instructions for future reference

Roof sizes:

4x6 Greenhouse = 1217mm

(8x6 Greenhouse with shed)

6x6 Greenhouse = 1800mm

(10x6 Greenhouse with shed)

8x6 Greenhouse = 2385mm

(12x6 Greenhouse with shed)

6x6 Greenhouse

(10x6 Greenhouse with shed)

8x6 Greenhouse

(12x6 Greenhouse with shed)

4x6 Greenhouse *Shown

(8x6 Greenhouse with shed)

Step 13 (internal)

Following the same method

outlined in Step 12, rest the

door side panels onto the

assembly and secure into

position using 50mm screws.

See greenhouse instructions

for screw quantities.

Door side panel size = 610mm

Pre drill

hole

50mm

screw

Step 14 (internal)

Attach the door gable top to

the front of the building as

shown in the illustration using

50mm screws - See greenhouse

nail bag.

See greenhouse instructions

for screw quantities.

Pre drill

hole

50mm

screw

Step 15 (internal)

Place the window into the roof and

secure into position using 6x16mm

screws and 6x30mm screws as

shown in the illustration - See

greenhouse nail bag.

See greenhouse instructions

for screw quantities.

Pre drill

hole

16mm

screw

30mm

screw

Please retain product label and instructions for future reference

Step 16 (internal)

Fix the casement stay to the

window using 20mm screws

as shown in the ilustration.

once in position secure the

pins to the roof framing with

20mm screws, ensuring the

stay and pins align and lock

the window - See greenhouse

nail bag.

See greenhouse instructions

for screw quantities.

Pre drill

hole

20mm

screw

Step 17 (internal)

Place the greenhouse roof frame(s)

(No. 11 - See front page) against each

window panel and secure in place

using 3x50mm screws per frame,

ensuring to screw into each panel.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 18 (internal)

Using the roof’s as a guide, mark the

position for the roof block (No. 12) at

the top of the shed door gable.

Once marked secure the block to the

gable using 1x70mm screw, making

sure to secure through the block into

the central upright on the door gable.

1x70mm Screws

Pre drill

hole

70mm

screw

16mm

screw

30mm

screw

Please retain product label and instructions for future reference

6x6 Greenhouse

(10x6 Greenhouse with shed)

8x6 Greenhouse

(12x6 Greenhouse with shed)

4x6 Greenhouse *Shown

(8x6 Greenhouse with shed)

Step 19 (internal)

With the roof block in place,

position the roof’s onto the

assembly ensuring they rest

on top of the gable top and

roof block (some adjustment

may be necessary ).

Once aligned secure the roofs

into situe - See greenhouse

nail bag. Internally screw

through the roof block into

each roof panel as shown in

the illustration using 2x50mm

screws.

See greenhouse instructions

for screw quantities.

2x50mm Screws

Pre drill

hole

50mm

screw

Step 21 (internal)

Fix the door to building using

16x16mm black screws.

Attach the turn buttons to the

greenhouse door gable with

2x30mm black screws.

Place the door rail onto the

base frame underneath the

door and secure using

3x40mm screws

See greenhouse instructions

for screw quantities.

Pre drill

hole

40mm

screw

Step 20 (internal)

Attach the roof support bar

- See greenhouse instructions

to the roof panels using 40mm

screws.

Screw diagonally through the

roof support bar into the panels

as shown in the illustration.

See greenhouse instructions

for screw quantities.

Pre drill

hole

40mm

screw

16x50mm Screws

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Please retain product label and instructions for future reference

SILICONE

SEALANT

Step 23 (internal)

It is advisable to seal around all

window framing with silicone

sealant (not included) to

minimize water ingress.

*Please note: This image is for

illustrative purpose and may

dier from your product (in

regards to the number of

windows) however the principle

is the same.

Step 22 (internal)

Attach the fascia’s from the

greenhouse - See greenhouse

instructions - to the front of the

building using 6x40mm screws.

At the rear of the building

(Shed section) x the fascias

(No. 10) to the gable with

40mm screws, making sure to

trap the felt between the

building and the fascia.

Secure the remaining two

fascias (No. 10) - from the shed

- across the joint of the two

roofs, ensuring to screw to both

the shed and greenhouse roofs

using to screws at each end-

point.

Fit the nials (No. 15) to the

front and rear of the building

with 2x40mm screws.

32x40mm screws

Pre drill

hole

40mm

screw

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01RAW1210DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644AXNE0656LBDDHGSD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1006DD-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHOPN0305-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN1008FGC31TWSA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HON51156-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628WKNE0304LBDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG003-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03COR0707-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01SHPSTR0402-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA10DDGP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02SNO0705-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products SI-002-001-0022 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products SELF BUILD PACK Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0707FGD2TW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB0808-V3 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung