Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03DTSHRA1008FGC42TW-V1

DIP TREATED SHIPLAP REVERSE APEX 10X8 FULLY GLAZED CONCERTINA

4, 2 TALL WINDOWS- SUMMER HOUSE

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

03DTSHRA1008FGC42TW-V1

Overall Dimensions:

Width = 3010mm

Depth = 2489mm

Height = 2670mm

Base Dimensions:

Width = 2912mm

Depth = 2350mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Secondary Door QTY 1

AI-STDFGSD475X1715-V1

Plain Door QTY 2

AI-STDFGPD475X1715-V1

Master Door QTY 1

AI-STDFGMD475X1715-V1

Door Strip- 12x60x1720mm QTY 2

S1260-1720mm

Roof Support Block - 27x44x140mm QTY 6

F2744-G-160mm

Ridge Bar - 27x70x1434mm QTY 2

F2770-1434mm

14 Panel Framing - 28x28x1464mm QTY 4

FS2828-1464mm

Roof Support Bar - 27x44x1262mm QTY 6

F2744-G-1302mm

Roof Support Brace - 27x44x450mm QTY 3

F2744-G-490mm

Cover Trim - 12x40x2043mm QTY 11

S1240-2043mm

18 Fascia - 12x60x1333mm QTY 4

S1260-1333mm

Door Support Bar - 27x44x2872mm QTY 1

F2744-2872mm

Rain Guard - 28x44x680mm QTY 2

RG2844-680mm

Floor Support- 28x28x400mm QTY 8

F2828-400mm

Small Panel QTY 4

AI-S11SHPP284X2015-V1

Door Panel QTY 1

AI-03S11SHFCD2360X2015-V1

Window Panel QTY 2

AI-03S11SH1TFWC687X2007-V1

Side Panel QTY 2

AI-S11SHPPTOV1623X2007-V1

Back Panel QTY 2

AI-S11SHPP1180X2015-V1

Floor QTY 4

AI-S11MBF1175X1456-V1 Roof QTY 2

AI-S11MBOHAR2390X1356-V1

Gable Top QTY 2

AI-S11SHAGT2310X559-V1

Roof QTY 2

AI-S11MBOHAR572X1356-V1

Butt Hinge QTY 14

PI-07-0066

Door Handle QTY 2

PI-07-0081

Turn Button QTY 2

PI-07-0034

“L” Bracket QTY 2

PI-07-0012

Press Lock QTY 1

PI-07-0162

Barrel Bolt QTY 6

PI-07-0114

“U” Channel QTY 3

PI-07-0013

Finial QTY 2

SHED DIAMOND FINIAL

Felt

PI-01-0003

P 3

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

50mm Screw QTY 151

40mm Screw QTY 42

60mm Screw QTY 28

35mm Bolt QTY 4

Felt Tacks QTY 132

25mm Screw QTY 70

30mm Screw QTY 121

10mm Screw QTY 36

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Step 1

Parts needed - No. 1 QTY 1

No. 12 QTY 2

No. 25 QTY 6

Lay the Door Panel (No.1) on a at

surface framing facing upwards. Attach

the plain doors (No.10) to the inside

framing of the door panel (No.1) using

3x butt hinges (No.19).

*Fix the hinges to the inside of the door

panel.

Fix to the door using 3x25mm screws &

3x30mm screws to the framing per

hinge, ensure the doors open freely,

folding back into the building unrestrict-

ed.

18x25mm Screws

18x30mm Screws

Internal

Pre drill

hole

25mm

screw

30mm

screw

Step 2

Parts needed - No. 10 QTY 1

No. 11 QTY 1

No. 25 QTY 8

Pre drill

hole

25mm

screw

25 25

Turn the door panel (No.1) over so the

framing is on the at surface. Fix the

master (No.8) and secondary door

(No.9) to the attached plain doors

with butt hinges (No.19) , using

6x25mm screws per hinge.

*Ensure the doors open freely,

folding back into the building

unrestricted.

48x25mm Screws

External

35mm

bolt

Pre drill

hole

10mm

screw

25mm

screw

Secure the barrel bolts (No.30) to the top

& bottom of each plain door and the

secondary door using 6x10mm screws.

Attach the press lock (No.29) to the

master door with 4x25mm screws, aligning

the barrel with the key hole.

*Ensure the key turns and locks properly

before xing to the door.

Fix the door handles (No.28) to the

outside of the master and secondary door

using the 35mm bolts provided.

36x10mm Screws

4x25mm Screws

4x35mm Bolts

Step 3

Parts needed - No. 28 QTY 2

No. 29 QTY 1

No. 30 QTY 6

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Please retain product label and instructions for future reference

Step 4

Parts needed - No. 1 QTY 1

No. 2 QTY 2

Fix the Plain Panel (No.2) and

Door Panel (No.1) together by

screwing through the framing

using 6x50mm screws.

Ensure to stagger screws to avoid

colliding.

12x50mm Screws

2 2

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Fix the WIndow Panel (No.3) and

Side Panel (No.4) together by

screwing through the framing

using 6x50mm screws.

Ensure to stagger screws to avoid

colliding.

Repeat this with the second

Window and Door panel but the

opposite way round, as shown in

the diagram.

12x50mm Screws

Pre drill

hole

50mm

screw

Step 5

Parts needed - No. 3 QTY 2

No. 4 QTY 2

IMPORTANT: Pre-drill before xing screws.

Secure the oor (No. 7) to the

Floor Blocks (No.22) using 8x30mm

screws per oor.

Repeat this for one other oor panel

16x30mm Screws

Pre drill

hole

30mm

screw

Step 6

Parts Needed - No.7 QTY 1

- No.22 QTY 4

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Step 7

Parts Needed - No.7 QTY 1

Secure the oor (No. 7) to the

assembly from Step 6, using 8x30mm

screws per oor.

Repeat this to create two assembled oors

16x30mm Screws

IMPORTANT: Pre-drill before xing screws.

P 5

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Place the assembled oor panels

(No.7) upside down onto a rm and

level base. Ensure the base has suitable

drainage, free from areas where

standing water can collect.

Secure the oors together using

12x50mm screws through the oor

bearers in an alternating pattern.

Once xed together turn the oor back

the right way up.

12x50mm Screws

Step 8

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Fix the Plain Panel (No.5) and

Small Panel (No.2) together by

screwing through the framing

using 6x50mm screws.

Ensure to stagger screws to avoid

colliding.

Repeat this with the second plain

and small panel but the opposite

way round, as shown in the

diagram.

12x50mm Screws

Step 9

Parts needed - No. 2 QTY 2

No. 5 QTY 2

Pre drill

hole

50mm

screw

5 2 2 5

Fix the corners of the small panel (No.2)

and the side panel (No.4) with 50mm

screws as shown in the illustration.

Fix the assembled plain panels (No.5)

together through the framing using

6x50mm

Ensure to stagger screws to avoid

colliding.

Do not secure the building to the oor

until the roof is tted.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 10

Parts Needed - No.2 QTY 2

- No.3 QTY 1

- No.4 QTY 1

- No.5 QTY 2

IMPORTANT: Pre-drill before xing screws.

Fix the corners of the front

(No.1 and No.2) and side

panels with 50mm screws as

shown in the

illustration.

Do not secure the building to

the oor until the roof tted.

9x50mm Screws

Pre drill

hole

50mm

screw

Step 11

Parts Needed - No.1 QTY 1

- No.2 QTY 2

IMPORTANT: Pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Fix the corners of the side

(No.4 and No.3) and the

front panels with 50mm

screws as shown in the

illustration.

Do not secure the building to

the oor until the roof tted.

6x50mm Screws

Step 12

Parts Needed - No.4 QTY 1

- No.3 QTY 1

IMPORTANT: Pre-drill before xing screws.

Step 13

Parts Needed - No.6 QTY 2

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Place the gable tops (No.6) onto

the window panels, ensuring the

boards interlock.

Secure in place using 4x50mm

screws per gable top, screwing in

an alternating pattern.

8x50mm Screws

Pre drill

hole

30mm

screw

Step 14

Parts Needed - No.14 QTY 4

Place the panel framing (No.14)

along the top of the panel at the

front and back of the building and

secure using 2x50mm screws per

framing piece.

8x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Connect the ridge bars (No.13) together

with the metal “U” (No.31) channel, using

10x30mm screws.

Attach the “L” (No.27) brackets to each

end of the Ridge support with 2x30mm

screws per bracket.

*Ensure the bracket are ush with the

ends of the ridge bar.

14x30mm Screws

Step 15

Parts Needed - No.13 QTY 2

- No.27 QTY 2

- No.31 QTY 1

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Align the ridge bar (No.12)

between the gables and secure to

the central uprights with 2x30mm

screws per bracket (No.27), as

shown in the illustration.

*Ensure the ridge bar is ush with

the top framing of the gable tops.

4x30mm Screws

Step 16

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Place the roof support bars (No.15)

against the ridge bar and the building,

making sure to align the roof support

bars with the upright framing on the

door panel and the back panel.

Secure the bars into the ridge bar with

1x50mm screw per bar, screwing at an

angle as shown in the illustration.

*Ensure to stagger the screws so as not

to hit one screw with another.

2x50mm Screws

Step 17

Parts Needed - No.15 QTY 2

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Fix the roof support blocks (No.19) to

the back and door panel upright fram-

ing, ensure there is 15mm between the

roof support bar and the panel framing,

secure with 2x50mm screws per block as

illustrated.

*Ensure the roof support bars meet the

blocks and are level with the gables.

Secure the roof support bar to the block

using 1x50mm screw screwing down

through the bar into the block as shown

in the illustration.

6x50mm Screws

Step 18

Parts Needed - No.19 QTY 2

15mm

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

40mm

screw

Secure the roof support brace

(No.16) between the roof support

bars using 2x40mm screws.

2x40mm Screws

Step 19

Parts Needed - No.16 QTY 1

Please retain product label and instructions for future reference

P 8

Pre drill

hole

40mm

screw

50mm

screw

Repeat Steps 17, 18 & 19 to nish

building the roof support.

4x40mm Screws

16x50mm Screws

Step 20

Parts Needed - No.15 QTY 4

- No.16 QTY 2

- No.19 QTY 4

15 15

IMPORTANT: Pre-drill before xing screws. Step 21

Parts needed - No 8 QTY 2

- No. 9 QTY 2

60mm

screw

Pre drill

hole

Place the Roof Panels (No. 8 & 9) on top of the

building making sure the framing in the roof

panels sits rmly within the Gables (No. 6) and

on top of the Ridge Bar (No. 13).

**Make sure that you have got the roof panels

the correct way round with the recess at the

top of the apex as shown in the diagram.**

From the top, x directly through the roof panels

(No. 8 & 9) into the ridge bar (No. 13) below

using 60mm screws. Fix a 60mm screw through

the roof panels (No. 8 & 9) into the Roof Support

Bars (No. 15).

It is essential that the ridge bar (No. 13), roof

support bars (No. 15) and roof panel (No. 8 & 9)

framing pull together when xed with 60mm

screws. You may require another person pushing

the ridge bar (No. 13) and Roof Support Bars (No.

15) up from below to achieve this.

HINT - Follow the nailing line of the framing on

the roof panel so that you are more likely to x

into the ridge bar below.

22x60mm Screws

IMPORTANT: Pre-drill before xing screws.

P 9

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

Step 22

40mm

screw

Before fully xing the roof, check by eye

to see that the walls are straight by

standing to the sides of the building.

Use 40mm screws to x the roofs (No. 8

& 9) down the sides, front and back of

the building.

Be sure that the screws attach into the

framing below.

24x40mm Screws 9

Pre drill

hole

Fix the roof framing together

using the “U” Channel (No.31),

laying evenly over the framing,

secure using 6x30mm screws

Repeat for both sides of the roof.

12x30mm Screws

Step 23

Parts Needed - No.31 QTY 2

30mm

screw

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Step 24

Secure the building internally to

the oors using 38x50mm screws.

*Ensure to screw through the

framing into the oor bearers.

38x50mm Screws

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

P 10

Felt

tacks

HANDLE

WITH CARE

Cut the felt (No.32) into 3 strips of

3100mm length and place onto

the roof, as shown in the

illustration.

Fix the sheets into place using

132x felt tacks approximately

100mm apart.

132x Felt Tacks

Step 25

Parts Needed - No.32 QTY 1 32

Pre drill

hole

30mm

screw

Attach the cover trims (No.17)

to each corner of the building

and across each joint between

the xed panels, using

3x30mm screws per cover trim.

33x30mm Screws

17 17

Step 26

Parts Needed - No.17 QTY 11

IMPORTANT: Pre-drill before xing screws.

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA0808FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628PNNE0325HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OSBP0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01BEACH-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Dutch Barn 8x8 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0806FGD1TW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0806SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG213-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0808FGD2TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0806PA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1210DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung