Mercia Garden Products 03LBRO1208-V7 Gebrauchsanweisung

P 1

03LBRO1208-V7

12x8 Combi Summerhouse

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUSTpilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for

maintenance, annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree

causing damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can

be helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm

sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm

above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

P 2

2345

6 7 8910

11 12 13 14 15

16 17 18

Door Panel Back Panel

Short Panel

Short Window

Panel

AI-03LBRO1208DP-V7

Internal Panel

AI-03LBRO1208BP-V7

AI-03LBRO1208SPP-V7

AI-03LBRO1208SWP-V7

AI-03LBRO1208INPP-V7

Floor

Roof

Front Window

Panel

Storage Door

Panel

Side Panel

AI-03LBRO1208F-V7

AI-03LBRO1208R-V7

AI-03LBRO1208FWP-V7

AI-03LBRO1208SDP-V7

AI-03LBRO1208PP-V7

QTY x2

Double Boarded Gable Top

Gable Top Right

Gable Top Left

AI-03LBRO1208GTDB-V7

AI-03LBRO1208GTR-V7

AI-03LBRO1208GTL-V7

Storage Gable

Left

Storage Gable

Right

AI-03LBRO1208SGPL-V7 AI-03LBRO1208SGPR-V7

Under Roof Veranda

Small Floor

AI-03LBRO1208UR-V7 AI-03LBRO1208V-V8

AI-03LBRO1208SF-V7

QTY x2

Storage Door

Slave Door

Master Door

AI-03LBRO1208MD-V7 AI-03LBRO1208SD-V7 AI-03LBRO1208SHD-V7

QTY x2

22 30

5x Floor Blocks - 28x28x400mm

Cover Trim A - 12x56x1980mm

2x Cover Trim B - 12x56x2000mm

Cover Trim C - 12x56x2011mm

Cover Trim D - 12x56x2040mm

Cover Trim E - 12x56x2070mm

2x Cover Trim F - 12x56x2080mm

2x Front Fascia - 12x134x1903mm

4x Side Fascia - 12x134x1250mm

F2828-400mm

S12134-1250mm

Fixing Kit

Door Stop

Felt

2x Press Lock Base-

28x28x95mm

37 38

Press Lock

Handle

4x Barrel Bolt

Fixing Kit continues on P3

S12134-1903mm

S1256-1980mm

S1256-2000mm

S1256-2011mm

S1256-2040mm

S1256-2070mm

S1256-2080mm

PLY TRIANGLE

F2828-95mm

PI-07-0162

PI-07-0114

PI-07-0159

2x Door Trim - 16x60x1698mm

F1660-1698mm (rounded edge)

Panel Framing- 44x44x1910mm

F4444-1910mm

17b

Plain Door

AI-03LBRO1208PD-V7

03LBRO1208-V7

Overall Dimensions:

Width =3796mm

Depth = 2514 mm

Height = 2146mm

Base Dimensions:

Width = 3688mm

Depth = 2439mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

P 3

2x Door Handles

PI-07-0001

Step 1

Secure the oor (No. 13) to the

Floor Blocks (No.22) and 10x30mm

screws per oor.

20x30mm Screws

Pre drill

hole

30mm

screw

Step 2

Place the 2 oor panels (No. 13) onto a rm

and level base, ensuring the

base has suitable drainage and is free from

areas where standing water can collect.

Secure the oors together using 10x30mm

screws per oor.

10x30mm Screws

Step 3

Flip over the two oor boards (No. 13)

Place the small oor (No. 14) ush against

the assembled oor and x to (No.13)

Using 4x50mm screws x the small oor in

place as shown in the diagram.

4x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

12x Butt Hinge

Key Plate

4x Turn Button

Fixing kit cont..

PI-07-0066

PI-07-0017

PI-07-0034

Mortice Lock

PI-07-0017

PI-02-1028

PI-02-1008

50mm Screw x 97

40mm Screw x 4

Felt Tacks x 199

30mm Screw x 168

10mm Screw x 16

30mm Black Screw x 4

Felt Tacks x 199

30mm Screw x 168

30mm Black Screw x 4

70mm Screw x 13

Nail Bag

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

*This building can be built with the shed on the LEFT hand side. Follow the

same steps but be aware to position panels to the opposite side.*

Step 4

Fix the side of the short panel (No. 4)

against the framing of the back panel (No. 5)

with 3x50mm screws as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Step 5

Fix the side of the short panel (No. 4)

against the side of the short window panel

(No. 3) with 3x50mm screws as shown in

diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

Step 6

Fix the side of one Back Panel (No. 5)

against the side of the other Back Panel

(No. 5) with 3x50mm screws as shown in

diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Step 7

Before xing the internal panel in position,

x the Right Gable Top (No. 20) in place

slotting the groove of the boarding on the

gable into the tongue of the internal panel

(No. 8) as shown with 4x50mm screws.

Once the Gable top is positioned and xed,

x the Panel Framing (No. 32) to the side of

the Internal Panel (No. 8) as shown making

sure it is ush to the panel and framing as

shown with 3x50mm screws.

Do not secure the building to the Floor

until the roof is tted.

7x50mm Screws

P 4

P 5

Step 8

Fix the side of the Internal panel/Panel

Framing (No. 8/No. 32) against the frame of

the Back Panel (No. 5). Align the panel with

Storage Floor as shown and x internally

with 3x50mm screws.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Step 9

Fix the Left Gable Top (No. 21) in place

slotting the groove of the boarding on the

gable into the tongue of the side panels

(No. 3,No. 4) as shown with 4x50mm

screws.

4x50mm Screws

Pre drill

hole

50mm

screw

Step 10

Place the Door Panel (No. 1) onto a at

surface and x the Front Window

Panel (No. 2) in place as shown.

Make sure the panels are ush to

each other.

3x50mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

70mm

screw

Step 11

Place the Door Panel/ Front Window

Panel (No. 1/No. 2) onto the

assembly between the Short Window Panel

(No. 3) and Internal Panel (No. 8). Fix internally with

3x70mm screws into the Internal panel and

3 x50mm screws into the Short Window Panel

as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

3x70mm Screws

3x50mm Screws

50mm

screw

Please retain product label and instructions for future reference

P 6

Please retain product label and instructions for future reference

Step 12c

Fit the mortice lock (No. 40) into

the recess and x in place with the screws

provided. Fit the key plate(No. 42) to the

opposite door using the 4X30mm screws

provided.

Fix door handles (No. 39) using 8x30mm

screws.

Fix the Door Cover Strips (No. 31) to the

plain (No. 17b) and slave door (No. 17),

positioning the strip with a small overhang

to the right hand door. Fit the barrel bolts

(No. 38) to top and bottom of the door

strips as shown in diagram. Use 4x10mm

screws per barrel bolt.

Ensure doors open and close freely.

10x30mm Screws

8x10mm Screws 40

42 The Mortice Lock is Reversible

Pre drill

hole

Step 12a

Attach the Plain Door (No.17b) to the door panel

using 3x butt hinges (No.41) per door.

18x30mm Screws

Pre drill

hole

30mm

screw

17b

Pre drill

hole

30mm

screw

Step 12b

Fix the master door (No.16) to the outside of the door framing

and slave door (No.17) to the attached plain doors with

3x butt hinges per door, using 6x25mm screws

per hinge.

*Ensure the doors open freely,

folding back into the building

unrestricted.

48x25mm Screws

Please retain product label and instructions for future reference

P 7

Step 16

Place the Storage Door panel

(No. 6) against the end of the Storage

Gable Sides (No. 9/10) and x into position

internally.

Fix with 3x50mm screws per side internally as

shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

6x50mm Screws

Pre drill

hole

50mm

screw

910

Step 15

Place the Storage Gable Sides Left/Right

(No. 9/10) against the sides of the Internal

(No. 8) and Side Panel (No. 7) with the

boarding facing outwards as shown.

Fix with 3x50mm screws per

gable side as shown in diagram.

Do not secure the building to

the Floor until the roof is tted.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 13

Fix the side of the Side Panel (No. 7)

against the framing of the back panel (No. 5)

screwing internally with 3x50mm screws

as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Step 14

Fix the Double Boarded Gable Top (No. 19)

in place slotting the groove of the boarding

on the gable into the tongue of the Side

Panels (No. 7) as shown with 4x50mm

screws.

4x50mm Screws

719

Pre drill

hole

50mm

screw

P 8

Please retain product label and instructions for future reference

Storage Door hinges tted on the right

hand side of the door which means that

your door will open on the left side.

Step 16b - Fitting Door

Secure the hinge (No. 41) to the

storage door (No. 18) and the

storage door panel (No. 6).

18x30mm Screws

Pre drill

hole

50mm

screw

18 41

Pre drill

hole

70mm

screw

Step 17

Lay the 2x Veranda (No. 15) face down, side by side

and x together with 3x70mm screws through the bearers

as shown in the diagram, to secure the

two Verandas together.

3x70mm Screws

Step 18

Place the assembled Verandas (No. 15) ush to the

building as shown to make sure the building

is square.

Step 19a

Place the Roof Panels (No. 11) onto the top

of the building. Align the 2 Roof Panels

so they sit square before xing into postion.

Do not secure the building to the Floor

until the roof is tted.

P 9

Please retain product label and instructions for future reference

Step 20a

Once the Roof is aligned and secure the

oor can be xed into postion.

Fix the building into place by screwing

through the panel framing, securing all of the panels

to the oor.

*External panels not shown

18x50mm Screws

Pre drill

hole

50mm

screw

Step 19b

Fix the two Roof panels together using

50mm screws oset from each other as shown

in the diagram.

Do not secure the building to the Floor

until the roof is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

Step 19c

Screw in 8x50mm screws securing the roof

panels (No. 11) x 2 to all of the panels on

the front of the building

Do not secure the building to the

Floor until the roof is tted.

*External panels not shown

8x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

Step 20b

Continue to x the building into place by

screwing through the panel into the oor.

*External panels not shown

Pre drill

hole

50mm

screw

Pre drill

hole

30mm

screw

Step 21

Place the Under Roof (No. 12) into position,

making sure it is ush to the Door panel

and Storage section.

Fix in place making sure to screw through

the Roof framing. Pre-drill holes rst.

15x30mm Screws

P 10

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 10DTBARK0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCOR0707-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG016-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RARE0302ND1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619VR3301-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619LOG003-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1206DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0408DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01COR0707-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03BRN0705-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTGRODB0808-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products CARLTON ARBOUR ESDXL21PT050 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V6 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03TGCOR0909DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628LOG127-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung