Mercia Garden Products 0628LOG127-V5 Gebrauchsanweisung

P 1

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

0628LOG127-V5

0628LOG127-V5 28mm 3x3m corner cabin

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

P 2

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Short Window Pack*

QTY 2

Single Door Pack*

0628LOG127-V5

Overall Dimensions:

Width = 4482mm

Depth = 3723mm

Height = 2923mm

Base Dimensions:

Width = 3255mm

Depth = 3899mm

Please retain product label and instructions for future reference

Starter Board - 28x66x1621mm QTY 1

LB28RT66-HLR-1621 (1x45 deg cut top, 1x45 deg cut bottom)

Log Board - 28x120x400mm QTY 18

LB28-BGR-400 (1x45 deg cut right)

Log Board - 28x120x400mm QTY 17

LB28-BGL-400 (1x45 deg cut left)

Log Board - 28x60x400mm QTY 1

LB28-HGR-400 (1x45 deg cut right, 60mm height board)

Log Board - 28x70x400mm QTY 1

LB28-HGL-400 (1x45 deg cut right bottom notch, 70mm height board)

Log Board - 28x120x1621mm QTY 1

LB28-J-1621 (1x45 deg cut left, 1x45 deg cut right top notch)

Log Board - 28x120x1621mm QTY 1

LB28-JD-1621 (1x45 deg cut left, 1x45 deg cut right top notch, door notch)

Log Board - 28x66x2028mm QTY 1

LB28RT66-AGR-2028 (1x45 deg cut left)

Log Board - 28x120x2028mm QTY 6

LB28-AGR-2028 (1x45 deg cut left)

Log Board - 28x120x2028mm QTY 1

LB28-J-2028 (1x45 deg cut left 50mm bottom notch)

Log Board - 28x120x2028mm QTY 1

LB28-JD-2028 (1x45 deg cut left 50mm bottom notch, window notch)

Log Board - 28x120x2028mm QTY 1

LB28-ADGL-2028 (1x45 deg cut right, window notch)

Log Board - 28x120x2028mm QTY 7

LB28-AGL-2028 (1x45 deg cut right)

Log Board - 28x64x2028mm QTY 1

LB28-AGHL-2028 (64mm high board, 1x45 deg deep cut right)

Log Board - 28x64x3000mm QTY 1

LB28-AH-3000 (64mm high board)

Log Board - 28x66x3000mm QTY 1

LB28RT66-A-3000

Log Board - 28x120x3000mm QTY 40

LB28-A-3000

Finisher Board - 28x80x1356mm QTY 1

LB28RG80-CGLR-1356 (2x61 deg cut, 1356mm nished)

Finisher Board - 28x80x1005mm QTY 1

LB28RG80-CGR-1005 (2x74 deg cut left, 1005mm nished)

Finisher Board - 28x80x1005mm QTY 1

LB28RG80-CGL-1005 (2x74 deg cut right, 1005mm nished)

Finisher Board - 28x80x717mm QTY 3

LB28RG80-CGL-717 (1x45 deg cut right, 717mm nished)

Finisher Board - 28x80x1228mm QTY 2

LB28RG80-C-1228

Finisher Board - 28x80x717mm QTY 3

LB28RG80-CGR-717 (1x45 deg cut left, 717mm nished)

Log Board - 28x120x639mm QTY 24

LB28-B-639

Log Board - 28x120x639mm QTY 12

LB28-BGR-639 (1x45 deg cut left)

Log Board - 28x120x639mm QTY 12

LB28-BGL-639 (1x45 deg cut right)

*All components for the Windows and Doors are

shown in the Windows and Doors instruction packs.

Roof Truss - 40x70x992mm QTY 3

AI-06LOGC3X3-LRT

Roof Truss - 40x70x992mm QTY 3

AI-06LOGC-RRT

P 3

Please retain product label and instructions for future reference

Bearer - 44x44x2808mm QTY 1

F4444-G-2808-PT

Bearer - 44x44x2720mm QTY 8

F4444-G-2720-PT

Bearer - 44x44x2513mm QTY 1

F4444-G-2513-PT (1x45 deg cut, 2513mm nished)

Bearer - 44x44x2262mm QTY 1

F4444-G-2262-PT (1x45 deg cut, 2262mm nished)

Bearer - 44x44x2011mm QTY 1

F4444-G-2011-PT (1x45 deg cut, 2011mm nished)

Bearer - 44x44x1361mm QTY 1

F4444-H-1361-PT (2x45 deg cut, 1361mm nished)

Bearer - 44x44x1820mm QTY 1

F4444-G-1820-PT (1x45 deg cut, 1820mm nished)

Bearer - 44x44x1864mm QTY 1

F4444-G-1864-PT (1x45 deg cut, 1864mm nished)

Storm Brace - 27x44x2000mm QTY 8

F2744-2000

45 Closure Trim - 16x28x2400mm (approx length) QTY 14

S1628-2400

Fascia - 16x120x3300mm QTY 2

SR16120-3300

Felt

Roof Truss - 40x70x1710mm QTY 1

AI-06LOGC3X3-FRTR

Roof Truss - 40x70x1710mm QTY 1

AI-06LOGC3X3-FRTL

Roof Truss - 40x70x2259mm QTY 3

AI-06LOGC3X3-CRT Roof Block - 40x90x143mm QTY 1

F4090-143 (54mm shoulder 1x20 deg cut)

Fascia - 16x120x2200mm QTY 3

S16120-2200

P 4

Please retain product label and instructions for future reference

Felt Tacks x850

90mm Screw x11

Nail Bag

40mm Screw x320

30mm Screw x86

120mm Screw x11

70mm Screw x84

70mm Bolt Set x16

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

MB16-P-152 QTY 1

MB16-P-362 QTY 1

MB16-P-571 QTY 1

MB16-P-781 QTY 1

MB16-P-990 QTY 1

MB16-P-1200 QTY 1

MB16-P-1409 QTY 1

MB16-P-1618 QTY 1

MB16-P-1828 QTY 1

MB16-P-2037 QTY 1

MB16-P-2247 QTY 1

MB16-P-2456 QTY 1

MB16-P-2666 QTY 1

MB16-P-2875 QTY 1

MB16-P-3085 QTY 1

Floor Board Pack

AI-0628LOG127-V3FBP

MB16-C-2748 QTY 15

MB16-P-2748 QTY 1

MB16-P-2734 QTY 1

MB16-P-2622 QTY 1

MB16-P-2510 QTY 1

MB16-P-2398 QTY 1

MB16-P-2286 QTY 1

MB16-P-2174 QTY 1

MB16-P-2062 QTY 1

MB16-P-1950 QTY 1

MB16RG60-P-1838 QTY 1

Roof Board Pack B QTY 2

AI-06LOG3X3RBP2

Roof Board Pack A QTY 2

AI-06LOG3X3RBP1

MB16-P-88 QTY 1

MB16-P-200 QTY 1

MB16-P-311 QTY 1

MB16-P-423 QTY 1

MB16-P-534 QTY 1

MB16-P-645 QTY 1

MB16-P-757 QTY 1

MB16-P-868 QTY 1

MB16-P-980 QYT 1

MB16-P-1091 QTY `

MB16-P-1203 QTY 1

MB16-P-1314 QTY 1

MB16-P-1426 QTY 1

MB16-P-1537 QTY 1

Roof Board Pack C QTY 1

AI-06LOG3X3RBP3

MB16-P-89 QTY 1

MB16-P-225 QTY 1

MB16-P-361 QTY 1

MB16-P-497 QTY 1

MB16-P-634 QTY 1

MB16-P-770 QTY 1

MB16-P-906 QTY 1

MB16-P-1042 QTY 1

MB16-P-1178 QTY 1

MB16-P-1314 QTY 1

MB16-P-1451 QTY 1

MB16-P-1587 QTY 1

MB16-P-1723 QTY 1

MB16-P-1859 QTY 1

MB16-P-1995 QTY 1

P 5

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

40 39

38 37 36

Pre drill

hole

70mm

screw

Step 1

Parts needed - No. 34 QTY 1

No. 35 QTY 1

No. 39 QTY 1

No. 40 QTY 1

No. 41 QTY 1

Lay the bearers (No. 34, 35, 39, 40

& 41) onto a rm and level surface

(free from areas where standing

water can collect ) as shown in the

illustration.

Fix the framing together at each

corner using 10x70mm screws,

ensuring the frame is ush.

10x70mm Screws

Pre drill

hole

70mm

screw

Step 2

Parts needed - No. 35 QTY 7

No. 36 QTY 1

No. 37 QTY 1

No. 38 QTY 1

Arrange the remaining framing

(No. 35, 36, 37 & 38) as shown in

the illustration.

*Ensure there is an equal

amount of space between each

frame.

Secure each of the frames in place

using 2x70mm screws for each side

of the bearer, ensuring the framing

remains level.

40x70mm Screws

IMPORTANT: Pre-drill before xing screws.

35 35 35 35 35 35

Example picture

2 screws per bearer per end.

Pre drill

hole

P 6

Please retain product label and instructions for future reference

Step 3

Parts Needed - No. 3 QTY 1

No. 13 QTY 1

No. 17 QTY 1

No. 21 QTY 1

No. 22 QTY 1

Place the starter boards

(No’s. 13, 17, 21 & 22 ) on to

assembled base frame along the

longest sides.

To put the nal starter

board (No. 3) in the correct

place you need to lift the end of

the board to the left (No. 17)

and ensure they slot into each

other.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame with

1x70mm screw as shown in the

illustration.

5x70mm Screws

70mm

screw

Step 4 (See Pre-Assembly)

Parts needed - No. 6 QTY 1

Make the assembly level by

adding another board (No. 6)

as shown in the diagram.

Fix using 1x70mm screw.

**Ensure to stagger the

screws so as not to collide

with the previous screw.

1x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

bStep 5 (See Pre-Assembly)

Parts needed - No. 4 QTY 6

No. 5 QTY 6

No. 14 QTY 6

No. 17 QTY 5

No. 22 QTY 11

Following the same method

outlined in Pre-Assembly, lay

the rst 6 boards (No’s. 4, 5, 14,

17 & 22) onto the starter

boards to create your rst level.

Please note the right hand side

of the door will be slightly

higher. This will even out when

the rest has been assembled.

*Ensure that the boards are

level and ush with each

other as you lay each one.

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

Step 9 (See Pre-Assembly)

Parts needed - No. 4 QTY 6

No. 5 QTY 6

No. 10 QTY 12

No. 11 QTY 6

No. 12 QTY 6

No. 22 QTY 12

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s. 4, 5,

10, 11, 12 & 22) onto the

assembly to bring the board

level to the top of the window

and door frames.

Please note when you get to the

top of the boards the right hand

boards will be slightly lower.

**Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the door

frame.

Step 6 (See Pre-Assembly)

Parts needed - No. 4 QTY 6

No. 5 QTY 6

No. 10 QTY 12

No. 11 QTY 6

No. 12 QTY 6

No. 22 QTY 12

Following the same method

outlined in Pre-Assembly, lay

the next 6 boards (No’s. 4, 5, 10,

11, 12 & 22) onto the

assembly to create your second

level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the door

frame by 12-13 boards, refer to

door installation instructions, if

not, you can install the door at

step 9.

10 10

11 12

10 10

Step 7 (See Window-Assembly)

Parts needed - No. 1 QTY 2

Refer to window assembly

instructions to assemble

windows.

Step 8

Parts needed - No. 1 QTY 2

Ensure that the lip of the

window frame is located on

the inside of the building .

P 8

Please retain product label and instructions for future reference

Step 11 (See Pre-Assembly)

Parts needed - No. 9 QTY 1

No. 16 QTY 1

No. 18 QTY 1

No. 22 QTY 2

Following the same method

outlined in Pre-Assembly, lay the

remaining boards (No’s. 9, 16, 18

& 22) onto the assembly to bring

the board level above the

window and doors.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Step 10 (See Pre-Assembly)

Parts needed - No. 7 QTY 1

Make the assembly level by

adding another right hand

board (No. 7) as shown in the

diagram.

**Ensure to stagger the

screws so as not to collide

with the previous screw.

Step 13

Parts needed - No. 19 QTY 1

No. 20 QTY 1

Lay the last two boards (No. 19

& 20)onto the front of the

assembly. Fix into position with

2x70mm screws per board by

screwing through the notches.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

916

815

IMPORTANT: Pre-drill before xing screws.

Step 12 (See Pre-Assembly

Parts needed - No. 8 QTY 1

No.15 QTY 1

No. 17 QTY 1

No. 22 QTY 2

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s. 8,

15, 17 & 22 ) onto the assembly

to bring the board level x2

boards above the window and

doors.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Pre drill

hole

70mm

screw

P 9

Please retain product label and instructions for future reference

Step 14

Parts needed - No. 31 QTY 1

No. 32 QTY 1

No. 33 QTY 1

No. 46 QTY 1

To begin building the roof structure,

place the front Truss left (No. 32) and

front truss right (No. 31) on the

buidling and attach to the roof block

(No. 46) using 1x70mm screws per

purlin.

Then attach the back long roof truss

(No. 33) to the block in the same

way. Screw down through the purlin

at an angle as shown in the diagram

using 1x70mm screws.

3x70mm Screws

Pre drill

hole

70mm

screw

Step 15

Parts needed - No. 33 QTY 2

Place and x the remaining two

long roof truss’ (No. 33) onto the

building.

Fix using 1x70mm screws per

purlin, screwing down through

the purlin at an angle into the

block as shown in the diagram.

Ensure the angled section

follows the roof block and meets

the front truss’ on either side.

2x70mm Screws

Pre drill

hole

IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws.

70mm

screw

Please note: You can adjust the

blocks attached to the roof

truss’ if necessary .

IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws.

IMPORTANT: Pre-drill before xing screws.

P 10

Please retain product label and instructions for future reference

Step 16

Parts needed - No. 29 QTY 3

No. 30 QTY 3

Secure the shortest Roof Truss’ (No’s.

29 & 30) to the long purlins as

shown in the illustration using

1x70mm screws per truss.

*Ensure the angled side of the short

truss is ush with the side of the

long truss. Then make sure the

block under the short truss is ush

against the wall of the building.

6x90mm Screws

Pre drill

hole

90mm

screw

Step 18

You can now x the assembled

roof truss’ to the building,

making sure the attached blocks

sit inside the assembly. Some

adjustment may be required to

ensure the roof structure rests

correctly.

Once in position x to the

building using 1x120mm screw

per purlin as shown in the

diagram.

11x120mm Screws

Step 17

Parts needed - No. 23 QTY 1

No. 24 QTY 1

No. 25 QTY 1

No. 26 QTY 2

No. 27 QTY 3

No. 28 QTY 3

Place the nisher boards (No’s.

23, 24, 25, 26, 27 & 28 )

around the building, locating

each block between the truss’.

Secure each board using

2x70mm screws, ensuring to

stagger the screws to avoid

colliding.

22x70mm Screws

Pre drill

hole

70mm

screw

Pre drill

hole

120mm

screw

24 27

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products ESDXL21PT001 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG004-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0808DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG174-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTMBPN0406BR-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0705HGD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBAX0103SD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619VR3301-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTSHAX05051W-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCOR0707-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHPN0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREENLEAN0804-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0406DDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHOSBRAX0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA1006DDFW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung