Mercia Garden Products 03WES1208-V2 Gebrauchsanweisung

P 1

03WES1208-V2

12x8 Wessex Summerhouse

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to protect

the product during transit and for upto 3 months against mould. To validate your

guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated

with a wood preserver within the rst three months of assembly and thereafter in

accordance with the manufactures recommendations. Care must be taken to ensure

the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions, The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instruction pages for youR specic product code

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

50mm Screw x110

40mm Screw x26

Felt Tacks x180

20mm Screw x14

30mm Screw x84

20mm Nails x50

16mm Black Screw x14

30mm Black Screw x76

Pre Assembly

Remove the transportation blocks

from the bottom of each panel

before beginning the assembly.

03WES1208-V2

Overall Dimensions:

Length = 4028mm

Width = 2830mm

Height = 2252mm

Base Dimensions:

Length = 3725mm

Width = 2413mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Door Gable

03WESDG2413X1297-V1

Plain Gable

03WES1208-V2PG

Window Side QTY 2

03WES1208-V2WS

Plain Side QTY 2

03WES1208-V2PS

Floor QTY 2

03WES1208-V1F

Veranda Floor

03WES1208VRDF-V1

Roof QTY 4

03WES1208-V1R

Master Door

03WESMD1720X600-V1

3 4 5 6

78 9

Slave Door

01WESSD1720X600-V1

Veranda Rail

03WESVRDRL-V1

Window QTY 2

01OW-V1

Glazing QTY 4

PI-05-0038

25 27

31 32

Final QTY 2

Veranda Support - 27x44x1685mm QTY 2

F2744-1685mm

Fascia - 12x95x1549mm QTY 4

S1295-1549mm

Door Strip - 12x60x800mm QTY 2

S1260-1549mm

Window Strip - 12x45x1037mm QTY 2

S1245-1037mm

Tower Bolt Strip - 19x45x140mm QTY 2

S1945-140mm

Cover Trims - 12x56x1665mm QTY 6

S1256-1665mm

Door Beading Strip - 12x17x1710mm QTY 2

BDC-1710mm

Door Beading Strip - 12x17x1207mm

S1217-1207mm

Roof Support - 44x58x2918mm

F4458-2918mm

Roof Support Block - 27x70x619mm QTY 2

F2770-659mm (Angled)

Window Beading Strip - 12x17x437mm QTY 8

BDC-437mm

Window Beading Strip - 12x17x348mm QTY 8

BDC-348mm

T Hinge QTY 4

PI-07-0021

Hinge QTY 6

PI-07-0004

Tower Bolt QTY 2

PI-07-0030

Casement Stay Qty 2

PI-07-0005

Press Lock

PI-07-0162

Turn Button QTY 2

PI-07-0034

Handle

PI-07-0032

“L” Bracket Qty 2

PI-07-0012

“U” Channel Qty 2

PI-07-0013

Nail Bag

Step 1

Insert the glazing sheet into the window rebate, ensure a

ush t. Attach window beading with the 25mm glazing

pins provided, x4 pins per beading. When nailing pins

protect the glazing sheet with a piece of cardboard or

similar to avoid breakage and scratches.

48x25mm Nails

25mm

Nails

Step 2

Fix the T hinges to the top and bottom of

each door and a hinge in the middle, as

shown in the illustration using 30mm black

screws. Secure each door to the door gable

again using 30mm black screws.

44x30mm Black Screws

Pre drill

hole

30mm

screw

Step 3

Fix the door beading strips to the door gable

using 4x30mm screws for each strip.

Make sure to attatch the strips by screwing

into the door gable through the strip

12x30mm Screws.

30mm

screw

Pre drill

hole

30mm

screw

Pre drill

hole

P 3

Please retain product label and instructions for future reference

24 24

Step 4

Attach the door strips to the master door,

securing into place using 3x30mm screws

per strip.

6x30mm Screws

Step 5

Place oor on rm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Place the two Floor Panels along side each

other so that the oor bearers sit ush

together and x with 8x40mm Screws.

8x40mm Screws

40mm

screw

Pre drill

hole

Pre drill

hole

50mm

screw

Step 7

Following the same method outlined

in step 6, attach the next plain side &

the window side onto the assembly.

Fix the panels with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 8

Following the same method outlined

in step 6, attach the door gable & the

remaining window side onto the

assembly.

Fix the panels with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

9x50mm Screws

P 2

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Step 6

Place the plain gable and rst plain

side onto the oor and x in place.

Fix the corners with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

3x50mm Screws

Step 9

Line the roof support blocks

against the gable framing &

x in place using 4x50mm per

block

Attach an “L” bracket to the

centre of each block using

2x30mm screws per bracket.

*Ensure to align the bracket with the

roof support bar.

Place the roof support bar on

top of the blocks and secure

through the “L” brackets, using

2x30mm screws per side.

8x50mm Screws

8x30mm Screws

Pre drill

hole

50mm

screw 30mm

screw

Step 10

Lay two roof panels upside

down on a at level surface

and connect together using

a “U” channel, securing with

10x30mm screws.

*Repeat this process with

the next two roof panels.

20x30mm Screws

Pre drill

hole

30mm

screw

Step 11

Locate the roof panels on to the

gables, making sure the roofs

sit inbetween the blocks on each

gable.

*Ensure there is approximately

50mm of roof overhanging at

the rear of the building.

Secure the roof section in place

with 12x50mm screws per side

side as shown in the illustration.

24x50mm Screws

Pre drill

hole

50mm

screw

Step 12

Once the roof is xed in

position, secure the

building to the oor using

40x50mm screws.

*Ensure to align the screws with

the oor bearers underneath.

40x50mm Screws

Pre drill

hole

50mm

screw

P 5

Please retain product label and instructions for future reference

Step 13

Place the veranda oor to the front

of the building and secure in place

using 4x50mm screws as shown in

the illustration.

*Before xing ensure the oor sits

centrally.

4x50mm Screws

Pre drill

hole

50mm

screw

Step 14

Locate the veranda side rails on to

the oor (making sure the rails

are ush to the edge of the oor)

and secure in place using 5x50mm

screws per side.

Fix a veranda supports to the front

of each rail with 2x50mm screws

per side.

14x50mm Screws

Pre drill

hole

50mm

screw

Step 15

Fix the cover trims to each corner of

the building and across the panel

joints on each side, securing the

trims in place with 18x30mm screws

18x30mm Screws

Pre drill

hole

30mm

screw

HANDLE

WITH CARE

Step 16

Cut the felt into 3 sheets and lay onto the

roof as shown in the illustration. Once

arranged secure the felt into position with

180x felt tacks at 100mm intervals.

*Ensure there is approximately 50mm of

overhanging felt around all sides.

180x Felt Tacks

Felt

tacks

P 6

Please retain product label and instructions for future reference

13 10

Step 17

Fix the fascia’s and nial’s to the

front and rear of the building

(trapping the felt between the

fascia and building), securing

into place using 16x40mm

screws.

16x40mm Screws

Pre drill

hole

40mm

screw

Please retain product label and instructions for future reference

Opening Window

Fixed Window

30mm

screw

30mm

screw

30mm

screw

16mm

screw

Pre drill

hole

Pre drill

hole

Pre drill

hole

Step 18

Place the cover strip 13mm above

the gap in the window panel and

x into place using 3x30mm screws.

6x30mm Screws

If you would like the widows

to open attach the window to

the strip using 2x butt hinges.

Fix the hinges to the window

using 3x16mm screws per

hinge and to the strip with

3x30mm screws.

12x16mm Black Screws

12x30mm Black Screws

If you would like the window

to be xed, secure the window

into the gap using 4x30mm

screws. Ensure to screw through

the window into the panel

framing.

4x30mm Screws

Step 19

Fix the casement stays to each

window and panel with 6x20mm

screws.

*Ensure the casement stay ts

onto the xings when closed

before securing into place.

12x20mm Screws

Pre drill

hole

20mm

screw

Step 20

Attach the tower bolt strips to the top

and bottom of the slave door with

2x30mm screws per strip.

Align the tower bolts onto the blocks

and secure in place using 6x30mm

black screws per tower bolt.

4x30mm Screws

12x30mm Black Screws

Pre drill

hole

30mm

screw

Step 21

Fix the press lock to the master door

using 4x30mm screws.

*Ensure the key hole lines up with the

lock and the mechanism can be opened

and closed without restriction.

4x30mm Screws

Pre drill

hole

30mm

screw

Step 22

Secure the handle to the master door

(external) with 4x30mm black screws.

4x30mm Black Screws

Pre drill

hole

Please retain product label and instructions for future reference

17 28

30mm

screw

30mm

screw

Step 22

Attach a turn button to the top and bottom

of the slave door (external) using 1x30mm

black screw per turn button, ensuring the

turn button can move without restriction &

catches the master door.

*These turn buttons help to keep your doors

straight during high and low levels of

moisture content in the air.

2x30mm Black Screws

Pre drill

hole

30mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Please retain product label and instructions for future reference

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0619LOG015-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0707FGD2TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0909FGD4TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HON51156-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01SHPWOR2010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO1006DD-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619PNSH1227FBSD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG018-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0707FGD2TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHPN0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG002-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02RSE0505-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCOR0707-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02GARA0806-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDAX0406HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0705SDFW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung