Mercia Garden Products 0634RASH0302FBSDNW-V1 Gebrauchsanweisung

P 1

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

0634RASH0302FBSDNW-V1

34MM LOG CABIN, REVERSE APEX, SHED EXTENSION, CORNER LODGE (PLUS), 5M X 3M, HALF

GLAZED DOUBLE DOORS, TWO SHORT WINDOWS, ONE FULLY BOARDED SINGLE DOOR.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts

To identify the xings

required for each step use a

measuring tape.

P 2

0634RASH0302FBSDNW-V1

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Width = 5078mm

Depth = 3172mm

Height = 2742mm

Base Dimensions:

Width = 4809mm

Depth = 2808mm

Please retain product label and instructions for future reference

Log Board - 34x120x2000mm QTY 21

LB34-B-2000

Finisher Board - 34x66x2000mm QTY 2

LB34-BH66-2000 (66mm height board)

Log Board - 34x120x2000mm QTY 1

LB34-BD-2000 (1 x Window Notch cut out)

Log Board - 34x120x587mm QTY 18

LB34-B-587

Bearer - 44x58x1884mm QTY 11

F4458-1884-PT

Roof Purlin - 45x120x3522mm QTY 1

F45120-AE-3522

Roof Board - 16x121x2000mm QTY 32

MB16-2000

Log Board - 34x120x587mm QTY 18

LB34-C-587

Finisher Board - 34x80x70mm QTY 2

LB34RG80-C-70

Finisher Board - 34x80x886mm QTY 4

LB34RG80-C-886

Floor Board - 16x121x2736mm QTY 19

MB16-2736

Double Storm Brace - 16x120x2110mm QTY 4

S16120-2110

**All components and the nail bag from 3m x 3m corner cabin

(0634CSNE0303HGDD2SW-V1)

will be required to construct the 5m x 3m corner lodge.**

These components are shown in the 3m x 3m corner cabin

instructions.

Fully Boarded Single Door Contents:

Left Handed Right Handed

Fully Boarded Single

Door QTY 1

AI-06LOGFBD750X1900-V1

Door Frame Left Upright - 71x70x2065mm QTY 1

AI-0634LOGDUFL-V3

Door Frame Right Upright - 71x70x2065mm QTY 1

AI-0634LOGDUFR-V3

Door Frame Top - 84x125x884mm QTY 1

AI-0634LOGSDTF-V3

Door Frame Bottom - 71x70x764mm QTY 1

AI-0634LOGSDBF-V3

Storage Door

Handle QTY 1

PI-07-0033

81 82

Dead Lock

QTY 1

PI-07-0200

Rain Guard QTY 1

RG2844-780 (28x44x780mm)

5x3 Log Cabin Contents:

P 3

Please retain product label and instructions for future reference

Log Board - 34x120x3000mm QTY 20 - Combined Total Required x 60

LB34-A-3000

Roof Truss A- 40x140x1604mm QTY 6 - Combined Total Required x 11

AI-06LOGC3RTA-V1

Bearer - 44x58x2808mm QTY 2 - Combined Total Required x 3

F4458-2808-PT

Storm Brace - 27x44x2000mm QTY 6 - Combined Total Required x 14

F2744-2000

Closure Trim - 16x28x2400mm (approx length) QTY 10 - Combined Total Required x 24

S1628-2400

Felt

Gable QTY 1 - Combined Total Required x 2

AI-0634LOGC3-G-V1

*Please note

The components listed below are featured in both contents lists for the 3m x m3 Corner Cabin

(0634CSBE0303HGDD2SW) as well as the 5m x 3m Corner Lodge.

The component numbers listed below are the same component numbers as listed in the 3m x 3m

Corner Cabin instructions, some numbers may be out of chronological order or skipped to satisfy this.

Please see the total combined quantity required for the 5m x 3m Corner Lodge

(3m x 3m Corner + 3m x 2m Pack B) listed next to the components below.

40 Log Board - 34x66x3000mm QTY 1 - Combined Total Required x 2

LB34RT66-A-3000

Fascia - 16x120x2000mm QTY 2 - Combined Total Required x 4

S16120-2000

Roof Spacers QTY 5 - Combined Total Required x 10

PI-07-0208 (20x100x2mm)

Adjustable Hinge QTY 6 - Combined Total Required x 9

PI-07-0209

17a 17c17b

Key Plate QTY 1 - Combined Total Required x 2

P 4

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

Felt Tacks x 850

90mm Screw x 58

40mm Screw x 415

30mm Screw x 69

120mm Screw x 8

70mm Screw x 28

80mm Bolt Set x 28

80mm Screw x 8

90mm Bolt Set x 8

60mm Screw x 26

Pre-assembly

*Please note:

Each board interlocks at either end in a staggered pattern.

Before securing ensure that the boards are tted properly in their respective

tongues and grooves.

Pre - Assembly

*Please note

To construct the 5m x 3m Corner Lodge, all components

from the 3m x 3m Corner Cabin (0634CSNE0303HGDD2SW)

will be required as well as all components from this set of

instructions.

Components for the 3m x 3m Corner Cabin can be found in

the contents of the 3m x 3m Corner Cabin instructions.

**DO NOT CONSTRUCT USING THE 3M X 3M CORNER CABIN

INSTRUCTIONS IF YOU ARE CONSTRUCTING THE 5M X 3M

CORNER LODGE.**

P 5

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Pre drill

hole

90mm

screw

Step 1

Parts needed - No. 53 QTY 1

No. 54 QTY 1

No. 59 QTY 1

No. 60 QTY 1

No. 61 QTY 1

Lay the bearers (No. 53, 54, 59, 60 &

61) onto a rm and level surface (free

from areas where standing water can

collect) as shown in the illustration.

*Ensure the 58mm side of the bearer

is laying on the base, so that you can

screw the bearers together on the

44mm side.

Fix the bearers together at each

corner using 2x90mm screws,

ensuring the frame is ush.

Once fully assembled, ensure the

bearers are square by measuring from

corner to corner, as illustrated, making

sure they are an equal measurement.

If the bearers are not alligned equally,

unscrew and adjust and re-align

accordingly.

10x90mm Screws

IMPORTANT: Pre-drill before xing screws.

Example picture

2 screws per bearer per end.

60 59

Pre drill

hole

90mm

screw

Step 2

Parts needed - No. 54 QTY 5

No. 55 QTY 1

No. 56 QTY 1

No. 57 QTY 1

No. 58 QTY 1

Arrange the remaining framing

(No. 54, 55, 56, 57, 58) as shown in

the illustration.

*Ensure there is an equal amount

of space between each frame.

Secure each of the frames in place

using 2x90mm screws for each end

of each bearer, ensuring the bearers

remains level.

36x90mm Screws

IMPORTANT: Pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Pre drill

hole

90mm

screw

Step 3

Parts needed - No. 53 QTY 2

No. 91 QTY 2

Lay the bearers (No. 53 & 91) onto a

rm and level surface as shown in the

illustration.

Fix the bearers together at each

corner using 2x90mm screws,

ensuring the frame is ush.

Once fully assembled, ensure the

bearers are square by measuring from

corner to corner, as illustrated, making

sure they are an equal measurement.

If the bearers are not alligned equally,

unscrew, adjust and re-align

accordingly.

8x90mm Screws

Example picture

2 screws per bearer per end.

Step 4

Parts needed - No. 91 QTY 9

Arrange the remaining bearers (No. 91)

inside the assembled frame.

*Ensure there is an equal amount of

space between each frame.

Secure each of the frames in place using

2x90mm screws for each end of each

bearer, ensuring the bearers remain

level.

Once fully assembled, ensure the

bearers are square by measuring from

corner to corner, as illustrated, making

sure they are an equal measurement.

If the bearers are not alligned equally,

unscrew, adjust and re-align

accordingly.

36x90mm Screws

Pre drill

hole

90mm

screw

P 7

Please retain product label and instructions for future reference

Step 5

** Please Note:

Your log cabin can be either Right

Handed or Left Handed, dependant on

your wants and needs. (See Contents

for image reference)

Please ensure to construct your Log

Cabin by following either the ‘Left

Handed’ or ‘Right Handed’ instructions

dependant on which side you choose.

Align the two bases together by the

longest bearer as shown in the

illustration.

Secure the base sections together using

10x70mm screws, ensuring to stagger

the screws so they do not collide.

10x70mm Screws

Pre drill

hole

70mm

screw

Left Handed

35 53

Right Handed

P 8

Please retain product label and instructions for future reference

Left Handed

Pre drill

hole

Step 6 - Left Handed

Parts Needed - No. 22 QTY 1

No. 32 QTY 1

No. 36 QTY 1

No. 40 QTY 2

No. 41 QTY 1

No. 83 QTY 2

Place the starter boards (No. 22, 32 & 40) on to the assembled base frame and place the rst four log boards

(No.36, 41 & 83) sitting in the notches as shown.

Ensure the boards sit square on the base using the same method used in Step 1. Measure from corner to

corner and ensure they are equal in measurement.

Once the boards are square, x the starter boards (No. 22, 32 & 40) in place, lift up the log boards (No.36,

41 & 83) and x each starter board in place using 1x70mm screw per notch.

Fix the log boards to the starter boards by screwing through the notch into the frame with 1x70mm screw

as shown in the illustration.

Secure boards (No.83) in place by screwing at an angle through the side of the log board into the end of the

starter boards (No.40 & 32) next to them,as shown in the illustration.

8x70mm Screws

70mm

screw

IMPORTANT: Pre-drill before xing screws.

83 40

Right Handed

*Ensure boards sit ush

Rubber Mallet

may be required

to t parts.

Pre drill

hole

Step 6 - Right Handed

Parts Needed - No. 22 QTY 1

No. 32 QTY 1

No. 36 QTY 1

No. 40 QTY 2

No. 41 QTY 1

No. 83 QTY 2

Place the starter boards (No. 22, 32 & 40) on to the assembled base frame and place the rst four log boards

(No.36, 41 & 83) sitting in the notches as shown.

Ensure the boards sit square on the base using the same method used in Step 1. Measure from corner to

corner and ensure they are equal in measurement.

Once the boards are square, x the starter boards (No. 22, 32 & 40) in place, lift up the log boards (No.36,

41 & 83) and x each starter board in place using 1x70mm screw per notch.

Fix the log boards to the starter boards by screwing through the notch into the frame with 1x70mm screw

as shown in the illustration.

Secure boards (No.83) in place by screwing at an angle through the side of the log board into the end of the

log boards (No.41 & 36) next to them,as shown in the illustration.

8x70mm Screws

70mm

screw Rubber Mallet

may be required

to t parts.

IMPORTANT: Pre-drill before xing screws.

*Ensure boards sit ush

Please retain product label and instructions for future reference

Step 7

Parts needed - No. 25 QTY 1

Make the log cabin level by

adding another board (No. 25)

as shown in the diagram. Fix

using 1x70mm screw.

**Ensure to stagger the screws

so as not to collide with the

previous screw.

1x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

Left Handed

Right Handed

Step 8

Parts needed - No. 23 QTY 6

No. 24 QTY 6

No. 33 QTY 6

No. 36 QTY 5

Lay the rst 6 boards (No. 23, 24, 33, 36, 41, 83, 86 & 87) onto the starter boards to create your rst level, follow-

ing the method as shown in the illustrated.

Please note the right hand side of the door will be slightly higher. This will even out when the rest has been

assembled.

*Ensure that the boards are level and ush with each other as you lay each one.

Ensure the boards (No.83 & 87) are level, ush and in line with the boards next to them.

Secure every other board (No. 83 & 87) in place by screwing through the side of the board at an angle into the

end of the board next to it (No. 41 & 33 left handed & 36 right handed), using 1x60mm screw per board.

6x60mm Screws

86 41

Left Handed

Right Handed

Rubber Mallet

may be required

to t parts.

No. 41 QTY 17

No. 83 QTY 5

No. 86 QTY 5

No. 87 QTY 5

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

80mm

screw

P 10

Step 9

Parts Needed - No. 11 QTY 1

No. 12 QTY 1

No. 13 QTY 1

No. 14 QTY 1

For the Double Door frame, arrange the left,

right, top & bottom door frames (No’s. 11, 12,

13 & 14) onto a level surface.

Secure the top and bottom frames to the

uprights using 2x80mm screw per corner,

ensuring the screws do NOT protrude through

the front of the door framing.

8x80mm Screws

Pre drill

hole

80mm

screw

IMPORTANT : Pre-drill before xing screws.

The internal lip of the door

frame should be positioned on

the inside of the building.

14 12

IMPORTANT : Pre-drill before xing screws.

79 77

Pre drill

hole

80mm

screw

Step 10

Parts Needed - No. 76 QTY 1

No. 77 QTY 1

No. 78 QTY 1

No. 79 QTY 1

For the Fully boarded single door frame,

arrange the left, right, top & bottom door

frames (No’s. 76, 77, 78 & 79)) onto a level

surface.

Secure the top and bottom frames to the

uprights using 2x80mm screw per corner,

ensuring the screws do NOT protrude through

the front of the door framing.

8x80mm Screws

The internal lip of the door

frame should be positioned on

the inside of the building.

Please retain product label and instructions for future reference

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPMOW4803-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG015-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644LOG213-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0404HGDD2SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1210DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX1006SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03VER0808-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0407DSHSA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V6 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Tulip Playhouse 02TUL411411-V4-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTJER0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHOSBRAX0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHAX0505HGD1W-V1-PEFC Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung