Mercia Garden Products 0644LOG213-V4 Gebrauchsanweisung

P 1

0644LOG213-V4(4x3m)

0644LOG213-V4: 4x3m reverse apex cabin (44mm)

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Felt

P 2

0644LOG213-V4

Overall Dimensions:

Width = 4036mm

Depth = 3142mm

Height = 2600mm

Base Dimensions:

Width = 3808mm

Depth = 2814mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Medium Window Pack*

QTY 4

Log 213 Gable - 2996mm

AI-0634LOG174G-V4

QTY 2

Starter Board - 66x44x4000mm QTY 2

LB44RT66-A-4000

Log Board - 120x44x233mm QTY 28

LB44-B-233

Log Board - 120x44x233mm QTY 28

LB44-C-233

Log Board - 120x44x4000mm QTY 19

LB44-A-4000

Log Board - 120x44x748mm QTY 28

LB44-B-748

Log Board - 120x44x1497mm QTY 28

LB44-B-1497

Roof Board - 121x16x1600mm QTY 72

MB16-1600

Floor Board - 121x16x2715mm QTY 34

MB16-2715

16 Bearer - 44x58x2814mm QTY 2

F4458-2814-PT

17 Bearer - 44x58x3691mm QTY 10

F4458-3691-PT

Purlin - 45x120x4004mm QTY 3

F45120-A-4004

19 Eaves - 44x27x4004mm QTY 2

F2744-4004

Fascia - 16x120x1604mm QTY 4

S16120-1604 (angled)

Log Board - 120x44x2996mm QTY 4

LB44-A-2996

Log Board - 120x44x1216mm QTY 8

LB44-B-1216

Fascia - 16x120x4036mm QTY 2

S16120-4036

Double Door Pack*

Log Board - 34x120x4000mm QTY 1

LB44-AD-4000

Log Board - 44x120x2996mm QTY 2

LB44-AD-2996

Storm Brace - 27x44x2000mm QTY 8

F2744-2000

23 Closure Trim - 16x28x2400mm (approx length) QTY 12

SI628-2400

*All components for the Windows and

Doors are shown in the Windows and

Doors instruction packs.

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

Felt Tacks x400

70mm Screw x60

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

Nail Bag

40mm Screw x536

30mm Screw x72

P 3

Please retain product label and instructions for future reference

90mm Bolt Set x16

Example picture

2 screws per bearer per end.

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

17 17 17 17 17 17 17 17

Pre drill

hole

70mm

screw

Step 1

Parts needed - No. 16 QTY 2

No. 17 QTY 10

Lay the bearers (No’s 16

& 17) onto a rm and level

surface (free from areas where

standing water can collect ) as

shown in the illustration.

Fix the framing together at

each corner using 8x70mm

screws, ensuring the frame is

ush.

8x70mm Screws

Pre drill

hole

70mm

screw

Step 2 (See Pre-Assembly)

Parts needed - No. 4 QTY 2

No. 10 QTY 2

Place the boards (No’s. 4 & 11 )

on to the assembled base

frame along the longest

sides.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame as

shown in the illustration.

4x70mm Screws

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

70mm

screw

Following the same

method arrange the remain-

ing framing (No. 17) inside the

assembled frame.

*Ensure there is an equal

amount of space between

each frame.

Secure each of the frames in

place using 2x70mm screws

for each side of the bearer,

ensuring the framing remains

level.

32x70mm Screws

P 5

Please retain product label and instructions for future reference

Step 3 (See Pre-Assembly)

Parts needed - No. 7 QTY 4

No. 11 QTY 8

No. 12 QTY 8

Following the same method

outlined in Pre-Assembly, lay the

rst 6 boards (No’s. 7, 11 & 12)

onto the starter boards to

create your rst level.

*Ensure that the boards are

level and ush with each other

as you lay each one.

IMPORTANT: Pre-drill before xing screws.

Step 4

Once you have laid 6 log boards (o

of the starter) up the door section,

slide the assembled door frame (No.

2) assembly over the boards resting

the frame on top of the starter board.

*Please note: This image is for

illustrative purposes and may dier

from your choice in product (regard-

ing door position). Nevertheless the

process of tting the door frame is

the same.

**Please Note: The short boards at

the

front of the building (either side of

the door and window opening’s) can

be placed either side depending on

your needs.

Step 5 (See Pre-Assembly)

Parts needed - No. 5 QTY 14

No. 6 QTY 14

No. 7 QTY 7

No. 8 QTY 14

No. 9 QTY 14

Following the same method

outlined in Pre-Assembly, lay

the next 6 boards (No’s. 5, 6, 7,

8 & 9) onto the assembly to

create your second level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame by 12-13 boards,

refer to door installation

instructions, if not, you can

install the door at step 7.

IMPORTANT: Pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Step 6

Once you have laid the second

level of boards onto the assembly

slide the window(s) (No. 1) between the

smaller boards and rest on to the

longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position ).

Nevertheless the process of tting

the window is the same.

Step 7 (See Pre-Assembly)

Parts needed - No. 6 QTY 14

No. 7 QTY 7

No. 8 QTY 14

No. 9 QTY 14

No. 12 QTY 2

No. 13 QTY 1

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s. 6,

7, 8, 9, 12 & 13) onto the assem-

bly to bring the board level to

the top of the window and

door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame.

P 7

Please retain product label and instructions for future reference

Step 8 (See Pre-Assembly)

Parts needed - No. 3 QTY 2

Place the gable tops (No. 3) onto the

assembly. Fix into position by

screwing through the notches

as shown in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

Pre drill

hole

70mm

screw

Pre drill

hole

Step 9

Parts needed - No. 18 QTY 3

Align the Purlin(s) (No. 18) into the

cut out slots on each gable top ensuring

each purlin interlocks the boards.

Secure the Purlins at each end by

screwing through the bars into the

boards (ensure to pre-drill to avoid

the boards splitting) using 4x70mm

screws per purlin.

*Please note: The gable shown is for

illustrative purposes and may dier

in width from your choice in product.

Nevertheless, despite any dierences

the process of xing the purlins

is the same.

12x70mm Screws

70mm

screw

IMPORTANT: Pre-drill before xing screws.

P 8

Please retain product label and instructions for future reference

Step 10

Parts needed - No. 14 QTY 72

Place the rst two roof board’s

(No. 14) onto the assembly on each

side, making sure the boards are ush

to the end of the roof purlin. Once in

position x to each purlin using

3x40mm screws.

Due to natural occurences of wood

shrinkage / expansion. You maybe

required to use the provided spacers

and place a space of 2mm to ensure

every roof board lines up with the

truss’.

*Ensure the roof boards meet at the

top of the apex and leave an

overhang at the bottom.

Continue adding the roof boards

along the roof, xing each one into

position using 3x40mm screws,

making sure that each board is

interlocked, ush at the bottom &

meet at the top of the apex.

The last board on each side

will overhang: Using a straight edge

and a pencil mark out a line as a

guide.

Cut along the pencil mark and

remove the excess. Place the cut

down board’s back onto the roof and

secure into place using 3x40mm

screws per board.

*Please Note: This image is for

illustrative purposes and may dier

from your choice in product. Never-

theless the process of cutting and

tting the last roof boards is the

same.

216x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Step 11

Parts needed - No. 19 QTY 4

Ensuring the roof boards are

ush at the overhanging side

and meet at the apex, x the

Eaves Frames (No. 19) to the

underside of the roof boards

using 9x40mm screws as shown

in the illustration.

*Please Note: This image is for

illustrative purposes and may

dier from your choice in

product. Nevertheless the process

of xing the eaves frames is the

same.

36x40mm Screws

40mm

screw

Pre drill

hole

P 9

Please retain product label and instructions for future reference

Step 12

Parts needed - No. 15 QTY 34

Place the rst Floor Board (No. 15)

inside the building ush to the log

board on one side. Continue adding

the oor boards (internally) making

sure to interlock each individual

board.

*Do NOT secure the boards until

the last board has been measured

and cut.

Following the same method outlined

previously, measure the gap between

the bottom of the tongue (on the last

board placed) and the log board.

Using a straight edge mark out the

measurement onto the last oor

board (No. 15) and cut along the

length removing the excess.

**Please note: Mark the nal board

2mm under the measurement; This

will allow the timber to expand and

contract correctly.

Once all the oor boards are in

position secure each board into

position using 8x40mm screws.

***Please Note: Ensure to screw

through each of the oor boards

into the oor bearers.

272x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Pre drill

hole

30mm

screw

*trim to t

Step 13

Parts needed - No. 23 QTY 6

Inside the building place the closure

trim (No. 23) against the boarding

and align with the roof as shown in

the illustration.

Once in position x each trim

into place by pre drilling a pilot hole

and using 6x30mm screws per trim,

equally spacing them along the face

of the board

36x30mm Screws

30mm

screw

Pre drill

hole

*Cut to t

Step 14

Parts needed - No. 23 QTY 6

Once the oor has been laid arrange the

closure trim (No. 23) around the outside

edge of oor (internally), measure and cut

down accordingly to best match the

internal space.

Secure each trim section into place using

6x30mm spaced equally along the board

as shown in the illustration.

*Do NOT x the closure trim to the oor

boards.

36x30mm Screws

P 10

Please retain product label and instructions for future reference

30mm

screw

HANDLE

WITH CARE

1. 2.

3. 4.

30mm

screw

Felt

tacks

Step 15

Parts needed - No. 24

Cut the felt into ve strips and

lay onto the roof in the order

shown in the illustration.

*Ensure there is approximately

50mm of overhanging felt each

side.

Once the felt is laid out x to the

roof using felt tacks at 100mm

intervals.

*Felt size: 4132mm

252x Felt Tacks

Step 16

Parts needed - No. 20 QTY 2

No. 21 QTY 4

Align the fascia’s (No. 20 & No.

21) with the roof and x into

place using 3x40mm screws

per fascia, making sure to

screw through the fascia into

the roof purlinsand eaves

frame.

*Ensure the angled cuts meet

at the top of the apex.

12x40mm Screws

Pre drill

hole

40mm

screw

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 02DTSHOPN0305-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1210DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG131-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1408-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG003-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTSHAX0806-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Groundsman Dutch Barn 8x8 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA1006DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO0705-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG173SG-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL0808DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX1006DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 05DTMBPN0503DD-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Rose Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung