Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

P 1

01PTOSBA0306DDNW-V1

3x6 Pressure Treated Shiplap apex double door no windows

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of

heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also

occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be

avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended

periods of warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The

cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at least

25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst

erecting or using this product.

Refer to the instructions pages for you specic product code

Pressure Treated Timber

Pressure treating is a chemical process which helps to protect wood against adverse weather which could

lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),

Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in

pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 2

01PTOSBA0306DDNW-V1

Overall Dimensions:

Width = 1871mm

Depth = 859mm

Height = 1569mm

Base Dimensions:

Width = 1760mm

Depth = 795mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Nail Bag

50mm Screws x31

40mm Screws x17

30mm Screws x84

20mm Screws x11

Felt Tacks x51

Ridge Bar - 28x28x744mm

FS2828-744mm

Eaves Frame - 28x28x835mm QTY 2

FS2828-835mm

Block - 28x28x140mm QTY 2

FS2828-140mm

Door Strip - 28x12x1590mm QTY 2

S1228-1590mm

Cover Trim - 45x12x1575mm QTY 4

S1245-1575mm

Fascia - 60x12x1000mm QTY 4

S1260-1000mm

Door Trim - 60x12x530mm

S1260-530mm

Door Trim - 60x12x1016mm

S1260-1016mm

Finial

Diamond Shed Finial

Turn Button QTY 3

PI-07-0034

T Hinge QTY 4

PI-07-0021

“L” Bracket QTY 2

PI-07-0012

15 16 17 18

Door Gable QTY 1

AI-01SHPDG1707X1960-V1

Plain Side QTY 2

AI-01OSBAPS800X1567-V1 Plain Gable QTY 1

AI-01SHPPG1707X1960-V1

Floor QTY 1

AI-01OSBF1760x795-V1

Roof QTY 2

PI-03-0344 Door QTY 2

AI-01MBDR1660X437-V2

1 2 3

4 5 6

Building Content:

Pre Assembly

Remove the transportation blocks from the

bottom of each panel before beginning

assembly. Each panel should have 2x blocks.

Step 1

Place the doors (No. 4) into the door

gable (No. 1) ensuring there is an even

gap around the doors.

Secure each door to the gable using 2x

T hinges (No. 17) and 7x30mm screws

per hinge.

*Ensure to x the hinges to the top &

bottom framing on each door.

28x30mm Screws

30mm

screw

Pre drill

hole

Step 2

Place the oor (No. 4) onto a rm and

level base. Ensure the base has suitable

drainage and is free from areas where

standing water can collect.

*See front page for base requirements.

Step 3

Place the plain gable (No. 3)

and the rst plain side (No. 4)

onto the oor and x at the

corner using 3x50mm screws.

Do NOT secure the building to

the oor until the roof has been

xed in place.

3x50mm Screws

50mm

screw

Pre drill

hole

P 3

Please retain product label and instructions for future reference

P 4

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 5

Fix the 2x “L” brackets (No. 18) to

either end of the ridge bar (No. 7)

using 2x20mm screws per bracket.

*Ensure the bracket plate(s) are

ush with each end of the ridge

bar.

Once in place position the ridge bar

between the gable and window

panel, securing into position using

2x30mm screws per side.

4x20mm Screws

4x30mm Screws

Pre drill

hole

20mm

screw

30mm

screw

718

Step 6

Fix both eaves frame (No. 9) to the

edge of both roof panels (No. 5)

taking care to attach the eaves

frames to the edge of the roof panel

that matches their lengths.

Fix the roof sheets to the roof

ensuring they come together at the

top using 10x30mm screws per roof

sheet.

*Ensure to screw the roof sheets

into the framing of the panels and

the ridge bar.

28x30mm screws

Pre drill

hole

30mm

screw

Step 7

Once the roof has been

xed in place, secure the

building to the oor using

50mm screws.

*Ensure to screw through the panel

into the oor bearers below using

the nailing pattern as a guide.

18x50mm screws

Pre drill

hole

50mm

screw

Step 4

Following the same method

outlined in Step 3, place the

assembled door gable and

the second plain side (No. 4)

onto the oor and x at the

corner using 3x50mm screws.

Do NOT secure the building to

the oor until the roof has been

xed in place.

9x50mm Screws

50mm

screw

Pre drill

hole

HANDLE

WITH CARE

416

Felt

tacks

*Felt size: 2150mm

P 5

Please retain product label and instructions for future reference

Step 8

Cut the felt into ine strip and lay

onto the roof as shown in the

illustration.

*Ensure there is approximately

50mm of overhanging felt around

the building.

Fix the felt onto the building using

the felt tacks supplied at 100mm

intervals.

50x Felt Tacks

Step 8

Place the door strips (No. 10)

inbetween the door and door gable

as shown in the illustration and x

into position using 4x30mm screws

per strip.

Attach the blocks (No. 9) to the

reverse of the door at the top and

bottom, screwing through the front

of the door into the block with

2x30mm screws per block.

x a turn button (No. 16) to each

block with 1x30mm screw per turn

button making sure the doors can

be locked to the framing.

10x30mm Screws

Pre drill

hole

30mm

screw

Step 9

Fix the door trims (No’s. 13 & 14)

onto the front of the doors (opposite

door to the turn buttons on the back)

securing the trims using 7x20mm

screws.

Attach the last turn button (No. 16)

to the front of the building (same

door as the trims) using 1x20mm

screw.

8x20mm Screws

Pre drill

hole

20mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

P 6

Please retain product label and instructions for future reference

Step 10

Arrange the cover trims (No. 11)

around the building at each corner,

secure each cover trim in position

using 3x30mm screws.

12x30mm Screws

Pre drill

hole

30mm

screw

Step 11

Attach the fascia’s (No. 12) and the

nials (No. 15) to the top of the

building using 40mm screws,

ensuring to trap the felt between

the fascia and building.

16x40mm Screws

Pre drill

hole

40mm

screw

Please retain product label and instructions for future reference

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTOVAX0806DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX10DDNWGP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG133-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTBARK0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN1208FGC32TWSA-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03COR0707-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 06LOG004-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OAOSB0702PB-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 06LOG003-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Tulip Playhouse 02TUL411411-V4-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0409-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03VER1008-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products OIDTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung