MERLYN 8 Series Bedienungsanleitung

INSTALLATION GUIDE

Bifold Door

Shower wall

Series 8 Bifold door/Shower wall

Corner Door

NOTE: When the products is being used as a Bifold in a recess or with a side panel it can be

used with or without a shower tray as it come with a bottom optional frame section.

We do not recommend using the door on a shower tray when used as a shower wall or corner

door as water tightness cannot be guaranteed as there is no bottom frame available.

Thank you for choosing Merlyn.Please familiarise yourself

with the fitting instructions before commencing fitting.

1. Check that you have the tools required.

2 that the installation site is compatible . Check

with size of door supplied

3. Check all the enclosure components.

4 that the installation kit is complete. Check

DO NOT attempt to install the product unless you can

tick ALL 4 boxes as satisfactory.

The wall plugs supplied with the installation kit are for

use in solid walls. Hollow or 'stud-partition’ walls will

require alternative fixings. Please consult a hard ware

supplier for the correct type.

It may also be necessary to consult your tiling supplier

about the correct method for drilling your tiles.

IMPORTANT

Any parts missing or damaged must be reported to your supplier within 5 days of purchase.

Inspect shower enclosure before fitting as no claims will be acceptable after product has been installed.

USE SAFETY EYEWEAR WHEN DRILLING

INSTALLATION GUIDE 1

860-890

760-790

960-990

670

780

Adjustment

560

Opening space

900

800

1000

Size

Adjustment when used as Bifold door in recess

820-840

720-740

920-940

Adjustment

900

800

1000

Size

Adjustment when used as Shower wall

720-750 520

760

680-700760

855-875

755-775

955-975

Adjustment‘X’

900x900

800x800

1000x1000

Size

Adjustment when used as Corner door

715-735760x760

Φ6x30 wall plug　

123456

17 18 19 20 21 22

Magnet profile universal cover cap

Closing post cover cap L/R

Magnet seal

Moving panel A

Moving door upright water seal

Hinge

Cover cap for wall protile L/R

Moving panel B

Cover strip

Wall profile

Cover strip clip

Flat head screw ST4x30

Handle

Bottom seal

Luna rail end cap hinged side L/R

Luna rail

Luna rail end cap closing side L/R

Magnet profile

Screw cover cap clip

Screw ST4x12

Screw cover cap

Magnet wall profile

INSTALLATION GUIDE 2

Part No. Part No.

M7009

B08070

M7017

2YS51

A2401201

M7100

M7103

M7104

M7105

M7106

M7107/M7108

/M7109

M7110

M7111

M7114

M7118

M7119

M7120

M7121 M7116

M7124

M7123

A2401201x6 B08070x8 M7124x3 M7123x3

4x30mm 4x12mm

H2O

6mm

Ø3mm

B08092x1

Ø3mm

2SY51x8

INSTALLATION GUIDE 3

Fixing kit components

Tools required

M7020

M7017x2 M7120x2 M7119x2 M7121x1

M7118x2

M7116x1

B08068x1

M7115x8

100％

Level !

TRAY MUST BE LEVEL IN ALL DIRECTIONS!

Ensure the shower tray is level in all directions and is

properly sealed to the wall. The wall must be tiled down to

the top edge of the tray. Do not angle out bottom tile.

TRAY MUST BE SEALED FULLY AROUND WHERE

THE TRAY MEETS THE WALL.

PROCEDURE

100％ level

INSTALLATION GUIDE 4

LH RH

Note:Determine the handing, note that the

wall profile is only fitted to the hinged side.

Determine distance from edge

of tray to front of profile.

Min 10mm

NOTE: If fitting as corner door please refer to the adjustment table on page 1.

We do not recommend fitting the product on a shower trays when used as a showerwall

or corner door.

LH RH

F G

INSTALLATION GUIDE 5

The door is set up as left hand,

to reverse for right hand follow

steps below

Remove bracket

and profile

Remove M7024

Remove M7025 Fit M7025 (part with V) to the

bottom of the profile

Flip the glass panels end over end

First loosen the top bracket and remove the profile and bracket assembly.

Then remove parts M7024 & M7025.

Note M7025 with V should always be on the bottom.

INSIDE

INSTALLATION GUIDE 6

NOTE: Make sure the cutout in the

top and bottom bracket faces in.Use spacer provided to set

the gap under the glass

INSIDE

TOP TIP ! Fit seal to side

closest to shower head.

Bottom of the seal should

be flush with the bottom of

the glass.

M7020

M7110

Drill three holes on the

inside of the wall profile

and fix using screws

A2401201

0-20mm Max

INSTALLATION GUIDE 7

INSIDE

Close door fully, align

magnets and mark

position the profile on

the wall.Align the Magnet profile

to the line and mark hole

position

Fit part to the

bottom of the magnet

profile assembly.

M7119

M7020

M7111

Cut excess only

from the hinged

side of both seals.

Make sure the

angled fin is to

the inside

M7107

Add dab

of silicone.

End of the bottom

seal should be flush

with the outside face

of the upright seal.

10 mm

Note: If fitting as a shower wall skip to step 10 for sealing instructions.

If fitting as a corner door skip to step 11.

Bottom

13mm

For Bifold in recess

or with side panel

ensure the magnet

is 13mm below the

glass panel

INSTALLATION GUIDE 8

Place Luna rail into

closing side (1) first,

then fit hinged side

foot plate (2).

M7118

M7119

NOTE: Make sure the handle is

fitted with the bump stops facing

to the outside.

M7017

M7115

M7116

M7117

M7120

M7121

WARNING - The bottom frame can only be used when the product is fitted as a Bifold in a recess or with a side

panel.It cannot be used for a showerwall or corner door situation.

The bottom profile must be used to ensure water tightness under the moving panel.We cannot guarantee

water tightness if this is not used.

24 h.

INSTALLATION GUIDE 9

SEALING INSIDE

INSIDE

Note:

SEALING OUTSIDE

OUTSIDE

Seal top to bottom on the

between the wall

profile and the wall.

Do not apply sealant on

the inside of the tray.

Seal only along bottom on the

between

glass/rail/profile and the tray

and approx 50mm up

between the wall profile and

the wall. Seal joint between

bottom profile and upright

profile.

Bifold Shower wall

Andere Handbücher für 8 Series

Inhaltsverzeichnis

Andere MERLYN Andere Handbücher

MERLYN

MERLYN 6 Series Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch