Metra Electronics BT-HD01 Bedienungsanleitung

REV. 2/9/2016 INSTBT-HD01

Installation instructions for part BT-HD01

CAUTION!

All accessories and switches must be connected before

cycling the ignition. Also, do not remove the factory radio with the key

in the on position, or while the vehicle is running.

• Adds Bluetooth audio streaming to the factory radio

• Can be operated with the handlebar controls

• Will play/pause with ignition on/off

• Will show up on the factory radio as HDBT

• BT-HD01 interface • BT-HD01 harness • 4’ Waterproof USB cable

FEATURES

INTERFACE COMPONENTS

• Wire cutter • Crimp tool • Solder gun • Tape • Torx driver

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

BT-HD01

Harley Davidson

Bluetooth Audio

Streaming Interface 2006-2013

Table of Contents

Pre-Installation.......................................................2

Fairing Disassembly ........................................... 3-4

Connections to be made.........................................5

Installing the BT-HD01............................................6

Pairing the BT-HD01 ...............................................6

Operation.................................................................6

APPLICATIONS

HARLEY DAVIDSON (with Advanced Radio)

Electra Glide 2006-2013

Street Glide 2006-2013

Road Glide 2006-2013

BT-HD01

Pre-Installation

• Turn the radio on and activate the FM source.

• Turn the ignition key switch to the off position.

• Press and hold any (2) soft buttons on the radio, and then turn the ignition key switch to the on position. The soft buttons are the numbered buttons on the radio.

• Continue holding the (2) soft buttons until “Diag Test” is displayed on the radio screen, and then let go.

• Press the soft key button “4” labeled “Software” on the radio screen.

• The radio screen will then show the current software version. If you do not have V8.250 or higher, please go to the following website to update the radio:

http://www.harleydavidson.com/en_US/Content/pages/genuine_motor_accessories/advanced-audio-system.html

• Follow the instructions on the website exactly as stated. If there are any questions with that process, contact Harley Davidson. Please do not contact Axxess/Metra for

any questions pertaining to updating the radio.

• If the radio has V8.250 or higher software, press the soft button “6” to exit the diagnostic mode.

Attention: Before beginning the installation, check the current software version of the radio following the steps below.

This product will not work on models with software versions lower than V8.250.

BT-HD01

Fairing Disassembly

FLH/Batwing models:

1. Cover the front fender.

2. Remove (2) T-27 Torx bolts from

inner fairing (under mirrors)

(Figure A, step 2)

3. Remove (2) T-27 Torx bolts from

outer edges of inner fairing near the

fork tubes (facing forward)

(Figure A, step 3)

4. Remove (3) T-27 Torx bolts from

bottom edge of windshield.

(Figure A, step 4)

Note: Windshield and fairing will

be loose once these screws are

removed. Use extreme caution not

to damage fairing or windshield.

5. Remove windshield taking caution

that the outer fairing is loose.

6. Lift away and unplug headlight to

remove outer fairing. (Figure B)

(Figure A)

(Figure B)

Step 2 Step 2

Step 3

Step 4

BT-HD01

Fairing Disassembly

Roadglide/Sharknose models

1. Loosen (6) T-25 Torx bolts from

bottom, middle and top of left and

right sides of the inner fairing.

(Figure A)

2. Use a 1/2” socket or box wrench

to remove the (2) acorn nuts that

hold each turn signal at the lower

fairing. Let the signals hang loose.

(Figure B)

3. Lift away the fairing, unplug the

headlights and remove.

(Figure A)

(Figure B)

Step 1 Step 1

BT-HD01

Connections to be made

• Remove the 35-pin connector from the radio. This is the larger connector of the (2)

connectors in the radio. If there isn’t a 35-pin connector in the radio, proceed to the

next step.

• Connect the male end of the BT-HD01 harness into the radio.

• Connect the female end of the BT-HD01 harness into the factory connector in the

vehicle. If there wasn’t a 35-pin connector in the radio, skip this step.

• The following (2) wires connect to the 23-pin radio connector. This is the smaller

connector of the (2) connectors in the radio. The factory connector has the pin cavity

locations stamped onto it.

• Connect the Black wire from the BT-HD01 harness to the wire located in pin-19 of the

23-pin radio connector.

• Connect the Red wire from the BT-HD01 harness to the wire located in pin-20 of the

23-pin radio connector.

Note: The BT-HD01 can operate in two different modes: CD mode (default) or SAT

mode. If you have a factory iPod interface installed and desire to keep it, change the

BT-HD01 to SAT mode. To do this you will need to cut the Grey loop wire coming out of

the BT-HD01, and then switch the 3-pin audio wire connection to the SAT setting.

19 20

This is the wire view of the connector

BT-HD01

Handlebar controls

• The UP and DN buttons will operate next/previous song, if applicable.

• The MODE SEL. button will cycle through the available sources.

Radio controls

• The soft buttons 1-6 will allow you to access the following features:

Pair (1), Play/Pause (2), Random (3), Next (4)

Note: After 5 seconds with no buttons being pressed, the radio will default to

the main screen.

Note: The BT-HD01 supports full text on the radio screen from most streaming

apps, pending the Bluetooth device supports AD2P.

Operation

Pairing the BT-HD01

• Turn the ignition key switch to the on position, and then turn on the radio. There

will be a new option on the radio screen titled “HDBT”.

• Select this option, and then select “Pair”.

• On the Bluetooth device search for “HDBT”, and then pair to the BT-HD01.

• Remove (3) Torx screws from the radio. (Figure A)

• Attach the BT-HD01 to the radio, then reinstall the (3) Torx screws, securing the

BT-HD01 to the radio.

• If the 4’ waterproof USB cable is desired to be used, route the USB cable out

from the lower fairing to the desired location. The USB cable is designed to be

mounted with a hole drilled into the fairing, if so desired.

• Reassemble the fairing in reverse order of disassembly.

Installing the BT-HD01

BT-HD01

Notes

REV. 2/9/2016 INSTBT-HD01

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

Installation instructions for part BT-HD01

IMPORTANT

If you are having difficulties with the

installation of this product, please call our

Tech Support line at 1-800-253-TECH.

Before doing so, look over the instructions a

second time, and make sure the installation

was performed exactly as the instructions

are stated. Please have the vehicle apart

and ready to perform troubleshooting steps

before calling.

REV. 2/9/2016 INSTBT-HD01

Instrucciones de instalación para la pieza BT-HD01

¡PRECAUCIÓN!

Todos los accesorios, interruptores, paneles de con-

troles de clima y especialmente las luces del indicador de las bolsas

de aire deben estar conectados antes ciclar la ignición. Además, no

quite el radio de fábrica con la llave en la posición o de encendido ni

con el vehículo funcionando.

• Añade bluetooth al radio de fábrica

• Puede operarse con los controles de los manubrios

• Reproduce/pausa con la marcha encendida/apagada

• Se muestra en el radio de fábrica como HDBT

• Interfase BT-HD01 • Arnés BT-HD01 • 4’ cable USB a prueba de agua

CARACTERÍSTICAS

COMPONENTES DE LA INTERFASE

• Cortacables • Ponchadora • Pistola soldadora • Cinta • Destornillador Torx

• Conectores (ejemplo: conectores de extremo, de campana, etc.)

HERRAMIENTAS REQUERIDAS

BT-HD01

Harley Davidson

Interfase de Audio Bluetooth 2006-2013

Indice

Pre-instalación .......................................................2

Desensamble del carenado................................ 3-4

Conexiones que se deben hacer ............................5

Instalación del BT-HD01 .........................................6

Emparejamiento del BT-HD01 ................................6

Operación................................................................6

APLICACIONES

HARLEY DAVIDSON (con Radio Avanzada)

Electra Glide 2006-2013

Street Glide 2006-2013

Road Glide 2006-2013

BT-HD01

Pre-Instalación

• Encienda el radio y active la fuente de FM.

• Ponga la llave de encendido en la posición de apagado.

• Presione sin soltar cualquiera de los (2) botones suaves del radio, luego gire la llave de encendido a la posición de encendido. Los botones suaves son los botones

numerados en el radio.

• Siga presionando los (2) botones suaves hasta que aparezca “Diag Test” en la pantalla del radio, luego suéltelos.

• Presione el botón suave “4” rotulado “Software” en la pantalla del radio.

• La pantalla del radio mostrará la versión de software actual. Si no tiene V8.250 o superior, vaya al siguiente sitio web para actualizar el radio:

http://www.harleydavidson.com/en_US/Content/pages/genuine_motor_accessories/advanced-audio-system.html

• Siga las instrucciones del sitio web exactamente como se indican. Si hay preguntas acerca del proceso, comuníquese con Harley Davidson. No se comunique con

Axxess/Metra para preguntas relacionadas con la actualización del radio.