Metrologic IS4225 ScanGlove Bedienungsanleitung

METROLOGIC INSTRUMENTS, INC.

IS4225 ScanGlove®

Laser Bar Code Scanner

Installation and User’s Guide

00-02258B_Front_Cover.qxd 5/30/2007 3:43 PM Page 1

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer, who may quote brief

passages in a review, or provided for in the Copyright Act of 1976.

Trademarks

Metrologic is a registered trademark of Metrologic Instruments, Inc.

Products identified in this document are hereby acknowledged as

trademarks, registered or otherwise, of Metrologic Instruments, Inc. or their

respective companies.

ABLE OF

ONTENTS

Introduction........................................................................................................... 1

Scanner and Accessories..................................................................................... 1

Scanner Installation.............................................................................................. 2

Scanner Configuration to the Host System........................................................... 3

Parts of the Scanner............................................................................................. 4

Visual Indicators ................................................................................................... 5

Audible Indicators................................................................................................. 9

Labels................................................................................................................. 10

Maintenance....................................................................................................... 11

Infrared (IR) Object Sensor ................................................................................ 12

Scan Field .......................................................................................................... 13

Specifications ..................................................................................................... 14

Default Settings .................................................................................................. 15

Troubleshooting Guide ....................................................................................... 21

Regulatory Compliance ...................................................................................... 22

Patents ............................................................................................................... 25

Limited Warranty ................................................................................................ 26

Index................................................................................................................... 27

NTRODUCTION

The IS4225 ScanGlove

is a fully automatic single-line laser barcode scanner.

The ScanGlove is designed to be used as a “hands-free” wearable scanner or a

stationary desktop scanner.

Every ScanGlove is equipped with ScanQuest

, a patented activation technology

that allows the scanner to read bar codes automatically as the operator presents

the bar code to the scanner. Additional features include; 52 scan lines a second,

short, or long-range activation and two universal glove sizes with left and right-

hand capabilities.

The IS4225 has built in decoding for applications that use a RS232, Keyboard

Wedge, Stand Alone Keyboard, Light Pen Emulation, or USB interfaces. All

models have Flash upgradeable firmware. For additional information on other

system interfaces, please call a Metrologic Customer Service Representative.

CAN

LOVE

ODEL

. I

NTERFACE

IS4225-38 USB Keyboard

IS4225-41D RS232 with Breakaway Cable and DIN Connector

IS4225-47 PC Keyboard Wedge and Stand Alone Keyboard

IS4225-81 Full RS232 and Light Pen Emulation

CANNER AND

CCESSORIES

ART

UMBER

ESCRIPTION

IS4225 IS4225 Laser Scanner

00-02258 Installation and User’s Guide

00-02544 MetroSelect

Single-Line Configuration Guide

45-45455 Black Adjustable Glove

If any item is missing or to order additional items, contact the dealer, distributor or call

Metrologic’s Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

CANNER

NSTALLATION

1. Turn off power to the host system.

2. Connect the communication cable to the proper port on the host device.

3. Turn on power to the host system.

When the IS4225 first receives power, the red LED will flash, the

green LED will flash, and then the scanner will beep once.

See power source caution statement on page 10 of this manual.

To maintain compliance with federal regulations 21 CFR, Part 1040.10,

section (f)(6) the scanner must be plugged into an electrical outlet with a

switch accessible to the user or be powered by a host system containing a

switch that will disable power to the scanner.

CANNER

ONFIGURATION

THE

OST

YSTEM

The IS4225 is shipped from the factory pre-configured to a set of default

parameters. It may be necessary to change the default parameters to match the

host system’s requirements or to enable additional scanner functions. For a list

of possible parameter settings, refer to the Default Settings section of this guide.

To modify the scanner’s default parameters follow the steps below using the

bar codes located in the MetroSelect Single-Line Configuration Guide

(

MLPN

00-02544).

1. Scan the

ENTER CONFIGURATION

MODE

bar code to enter configuration mode.

The scanner will beep three times.

2. Scan the bar code(s) for the desired parameter(s).

The scanner will beep once.

3. Scan the

EXIT CONFIGURATION

MODE

bar code to exit and save the new

parameter settings. The scanner will beep three times.

If during the configuration process, there is a need to return the

scanner to the original factory settings, scan the recall defaults bar

code in the MetroSelect Configuration Guide. All settings selected

during that session or any previous sessions are discarded when you

scan the recall defaults code.

ARTS

THE

CANNER

Figure 1. Scanner Parts

Item

No. Description

 Green LED

When a bar code is read successfully, the green LED will flash.

 Red LED

When the red LED is illuminated, the laser is on.

 Red Output Window (Laser Aperture)



Infrared Sensor (IR)

If a specified time has elapsed without any scanning, the unit will

enter a “standby” mode. To reactivate the unit, place an object in

front of the IR sensor. The red LED will turn on when the scanner

is ready to scan.

 Communication/Power Cable

This cable’s termination is application dependent.

ISUAL

NDICATORS

There is a red and a green LED located on the top of the scanner. When the

scanner is on, the flashing or constant, illumination of the LEDs indicates the

status of the current scan and the scanner.

No Red LED Illumination of the LEDs will not occur if the scanner has

remained dormant for a specified time and the scanner is

not receiving power from the host. To reactivate the unit,

direct the output window up then down toward the object.

Red Flash;

Green Flash;

Steady Red

When the scanner first receives power, the red LED will

flash, followed by the green LED, and then the unit will

beep once. The red LED will stay on after it flashes once.

Steady Red When the laser is on, the red LED will be on. This occurs

when an object is detected in the scan field. If the scanner

cannot detect a bar code within approximately 2.5 seconds,

the unit will go into standby mode then the red LED will

shut off indicating that the laser is no longer on.

Steady Red

LED; Green

Flash

When the scanner successfully reads a bar code, the green

LED will flash and the unit will beep once. If the green LED

does not flash or the scanner does not beep, then the bar

code was not successfully read.

Repetitive Red

LED Flashing

The red LED will flash repeatedly when the IR sensor is

detecting a stationary object in the scan field.

To eliminate this disturbance, direct the scan window

toward a different location or remove the stationary object

from the IR field.

Steady Green

LED

After a successful scan, the scanner transmits the data to

the host device. When the host is not ready to receive the

information, the green LED will remain on until data can

transmit.

IGNAUX

PTIQUES

Sur la partie supérieure du scanner se trouvent une diode LED rouge et une

diode LED verte. Quand le scanner est sous tension, les diodes rouge et verte

clignotantes ou allumées vous informent sur l'état de palpage et de scanner.

Ni la diode

rouge, ni la

diode verte

n'est allumée

Il existe deux raisons possibles pour que les diodes ne

s'allu-ment pas. Si le scanner ne reçoit pas d'énergie de

l'ordinateur PC, les diodes ne s'allument pas. Quand le

scanner reçoit de l'énergie et ne s'allume cependant pas, le

scanner est resté pendant une certaine période sans être

utilisé et le laser et lemoteur sont désactivés. Pour

réactiver l'unité, déplacer un objet devant le palpeur

infrarouge ou prendre le scanner et diriger la fenêtre de

palpage vers le bas.

Diode rouge

clignotante;

diode verte

clignotante;

diode rouge

reste allumée

Quand le scanner reçoit pour la première fois de l'énergie,

la diode rouge se met d'abord à clignoter, puis la diode

verte. Ensuite, le scanner émet un bip sonore unique. Une

fois cette séquence de démarrage effectuée, la diode

rouge reste allumée pendant un certain temps indiquant

que le laser est en service. Quand le scanner ne détecte

aucun objet, la diode rouge et le laser s'éteignent.

Diode rouge

reste allumée

Quand le laser est activé, la diode rouge s'allume

également. C'est par exemple le cas quand un objet se

trouve devant la fenêtre de palpage. Si, en l'espace de 2,

5 secondes, aucun code barres n'est détecté, la diode

rouge s'éteint, ce qui signifie que le laser est désactivé.

Diode rouge

reste allumée;

diode verte

clignotante

Après lecture avec succès d'un code barres par le scanner,

la diode verte se met à clignoter, suivie d'un bip sonore

unique. Si la diode verte ne clignote pas ou quand aucun

bip sonore n'est émis, cela signifie que le code barres n'a

pas pu être lu avec succès.

Clignotement

répété de la

diode rouge

Quand la diode rouge clignote plusieurs fois pendant que

l'appareil repose sur une surface non déplacée, un objet

activant le palpeur infrarouge se trouve devant la fenêtre

de palpage. Ceci peut se produire même quand le scanner

se trouve sur une table ou un reposoir. Pour éliminer ce

défaut, positionner le scanner de façon différente.

Diode verte

reste allumée

Une fois le palpage effectué avec succès, le scanner

transmetles donnéesà l'ordinateur PC. Si ce dernier n'est

pas prêt à recevoir les données, la diode verte du scanner

s'allume jusqu'à ce que les donnés puissent être

transmises.

Andere Handbücher für IS4225 ScanGlove

Inhaltsverzeichnis

Andere Metrologic Barcode-Lesegerät Handbücher

Metrologic

Metrologic MK3780-31A62 Bedienungsanleitung

Metrologic

Metrologic ScanQuest IS4110 Bedienungsanleitung

Metrologic

Metrologic MS7820 Solaris Bedienungsanleitung

Metrologic

Metrologic MS9530 Series Bedienungsanleitung

Metrologic

Metrologic 160 Benutzerhandbuch

Metrologic

Metrologic MS 1690 Focus Series Bedienungsanleitung

Metrologic

Metrologic Genesis MS7580 Betriebsanleitung

Metrologic

Metrologic MS1633 FocusBT Bedienungsanleitung

Metrologic

Metrologic Genesis MS7580 Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Metrologic

Metrologic TwinScan IS220 Bedienungsanleitung

Metrologic

Metrologic Cubit MS6520 Series Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Metrologic

Metrologic MS5100 Eclipse Series Bedienungsanleitung

Metrologic

Metrologic MS 1690 Focus Series Bedienungsanleitung

Metrologic

Metrologic MS7600 Bedienungsanleitung

Metrologic

Metrologic Tire and Rubber Benutzerhandbuch

Metrologic

Metrologic MK3780-31A62 Bedienungsanleitung

Metrologic

Metrologic MS7320 InVista Series Bedienungsanleitung

Metrologic

Metrologic MS7120 Orbit Bedienungsanleitung

Metrologic

Metrologic Stratos MS2xxx Series Montage- und Bedienungsanleitung

Metrologic

Metrologic MS6720 Bedienungsanleitung

Metrologic

Metrologic Cubit IS6520 Series Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung