Micanan Pro-APTC Kurzanleitung

installation &

instruction manual

Serial #:

Installation Date:

Wiring Diagram:

PRO-APTC

TABLE OF CONTENTS

PAGE:

VERIFICATION OF OPERATOR AND HARDWARE 3

SPECIFICATIONS 4

SAFETY INSTRUCTIONS 5

INSTALLATION 6

ELECTRICAL CONNECTIONS AND SETTINGS 10

LIMIT SWITCH ADJUSTMENT 20

PHOTOCELL INSTALLATION INSTRUCTIONS 21

EMERGENCY MANUAL OPERATION 24

OPERATOR MAINTENANCE 25

MECHANICAL DRAWINGS AND PARTS LISTS 26

ELECTRICAL DIAGRAMS 28

WARRANTY 32

WARNING

DO NOT CONNECT TO ELECTRICAL

POWER DURING INSTALLATION

OR SERVICING OF OPERATOR

IMPORTANT

FOR ANY QUESTIONS CONCERNING THE SAFETY OR

OPERATION OF THIS OPERATOR PLEASE CONTACT

MICANAN SYSTEMS AT 1-877-888-1116

SAVE THESE INSTRUCTIONS

For more information, please visit www.devancocanada.com

or call toll free at 855-931-3334

Upon delivery of your MICANAN SYSTEMS heavy-duty apartment/condo trolley door operator, please inspect the unit

carefully for damage. Verify that operator horsepower, voltage, phase and amperage correspond to available power supply

and door application. The operator is shipped with rails, drive chain, carriage and the straight-bar of the trolley arm already

assembled. Check that along with your operator/rail assembly you have received the following standard hardware.

1 x OPEN /CLOSE/STOP 3-button control station:

1 x Trolley arm curved bar with wall door attachment bracket

1 x Warning sign

1 set of REBEL monitored photocells (supplied when operator ordered

with monitored logic board controls)

VERIFICATION OF OPERATOR AND HARDWARE

PRO-APTC heavy-duty apartment/condo trolley operators are designed for standard lift overhead sectional garage doors.

Model PRO-APTCB is essentially the same as model PRO-APTC with the exception that the PRO-APTCB operator has an

electric braking system.

STANDARD OPERATOR WEIGHT: Operator/rail assembly: 150 Lbs

MOTOR:

• Standard: 1/2HP 110V: Instant reversing 1625RPM with built-in manual reset overload protection

• For applications other than 110V 1-phase:

Motor: 1/2HP Continuous duty 1725 RPM industrial type motor.

- Built-in overload protection (3-phase) or separate full overload protection (1-phase).

- Voltage: 230V 1-phase (60Hz) 230V 3-phase (60 Hz) 220V 1-phase (50Hz)

460V 3-phase (60Hz) 380V 3-phase (50Hz)

575V 3-phase (60Hz)

• For high speed VFD option: 3/4HP 230V 3-phase Continuous duty 1725 RPM industrial type motor.

REDUCTION: Heavy duty worm gear reducer 40:1 reduction, or 25:1 (high speed VFD option)

OUTPUT SHAFT SPEED: 40 RPM DOOR SPEED (standard): 7”/second

BRAKE (Model PRO-APTCB): Magnetic braking system to prevent coasting and maintain door position.

WIRING TYPE (3 OPTIONS):

Option 1: Full Feature logic board Smart 10.0 (UL325 (2010) compliant). Note: Micanan compatible primary entrapment

device must be connected for B2, T or TS (momentary or timer activation on close) feature. Auxiliary traffic

light board.

Option 2: VFD controller for ultra high-cycle/high-speed application.

TRANSFORMER: 24VAC control circuit, supplies power to drive controls with 15VA power available for external devices.

LIMIT ADJUSTMENT: 4 micro switches that control door travel. These limit switches are activated by fully adjustable

screw type cams.

EMERGENCY DISCONNECT: Dual handle quick release disconnect carriage with re-engage feature to allow person to

disengage operator drive chain from door for manual operation.

OPERATOR DIMENSIONS:

PRO-APTC SPECIFICATIONS

- READ AND FOLLOW ALL INSTRUCTIONS

- Never allow children to operate or play with door controls. Keep the remote control (where provided) away from children.

- Personnel should keep away from a door in motion and keep the moving door in sight until it is completely closed or

opened. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR.

- Test the door’s safety features at least once a month. After adjusting the limit of travel, retest the door operator’s safety

features. Failure to adjust the operator properly may cause severe injury or death.

- For products having a manual release, if possible, use the manual release only when the door is closed. Use caution when

using this release when the door is open. Weak or broken springs may cause the door to fall rapidly, causing severe injury

or death.

- KEEP DOORS PROPERLY OPERATING AND BALANCED. See Door Manufacturer’s Owner’s Manual. An improperly

operating or balanced door could cause severe injury or death. Have trained door systems technician make repairs to cables,

spring assemblies, and other hardware.

- Press the “OPEN” device or use emergency disconnect mechanism if a person is trapped under the door.

-SAVE THESE INSTRUCTIONS. The owner or users must understand the safety and operation of door system. Insure that

this installation manual be located close to the door system.

- READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS

- Commercial door operators are never to be installed on a residential installation

- Install only on a properly operating and balanced door. A door that is operating improperly could cause severe injury. Have

qualified service personnel make repairs to cables, spring assemblies, and other hardware before installing the operator.

- Remove all pull ropes and remove, or make inoperative, all locks (unless mechanically and/or electrically interlocked to the

power unit) that are connected to the door before installing the operator.

- Install the door operator at least 8 feet or more above the floor if the operator has exposed moving parts.

- Do not connect the operator to the source of power until instructed to do so.

- Locate the control station: (a) within sight of the door, (b) at a minimum height of 5 feet so that small children cannot reach

it, and (c) away from all moving parts of the door.

- Install the Entrapment Warning Placard next to the control station in a prominent location.

- For products having a manual release, instruct the end user on the operation of the manual release.

- Install non-contact entrapment protection devices (photocells) and/or contact entrapment protection devices (reversing

edges). Note: photocells should be installed at no more than 6” from the floor. Edges should be installed on the leading

edge of the door.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF INJURY OR DEATH:

Note: Installation of operator must be done by a qualified installer. Door must be properly installed and working smoothly.

Remove all door locks prior to installation.

1. Install control station away from all moving door parts, within sight of the door and a minimum of 5 ft (1.5 m) from

the ground.

2. Install entrapment warning sign next to control station.

INSTALLATION INSTRUCTIONS

WARNING

DO NOT INSTALL THIS OPERATOR

BEFORE READING THIS MANUAL CAREFULLY.

3. Do not remove emergency release handles or tags attached to trolley carriage.

WALL MOUNTING BRACKET AND OPERATOR INSTALLATION:

NOTE: Trolley type operators should generally be mounted directly over the center of the door and the trolley rails should

clear the tracks by 2-1/2” (6.5 cm). However, if interfering structures or other reasons do not allow for centered mounting, it

is possible to install it up to 18” off-center for torsion spring doors.

1. With door closed, locate the center of door by measuring door width and mark a vertical line above the door (Fig A).

2. Open door and mark the center line of the door on the ceiling (Fig B).

3. Determine the highest point of door travel by manually opening the door. Using a carpenter’s level, project a line from

where the top section of door reaches its highest point. Mark the spot where this line (high arc) intersects with the

vertical line drawn earlier.

4. Close door. Lay out operator/rail assembly on ground (upside down) in front of door with door operator facing away

from door.

5. Install curved trolley arm/door bracket to the trolley arm flat bar that is connected to the carriage. (Fig C). The trolley

arm is adjustable so do not tighten bolts at this time.

6. If required, mount a wood block or angle iron to the wall above the door opening (Fig D).

7. Flip operator assembly so that carriage/trolley are facing the ground. While allowing motor side to rest on floor, lift rail

assembly side of operator above door and align according to previously identified centerlines (Fig E). The wall

mounting bracket has 5 holes for anchoring to wood block or angle iron or direct to wall. Bracket should be centered

with door and positioned so that these holes are 2-1/2” (6.5 cm) above the high arc line of door. Secure wall mounting

bracket by welding or using suitable hardware.

8. Swing the operator above the level of the door tracks and temporarily secure in place with a post, or rope or chain

(Fig F). Carefully open door. Align operator and rails with center of door (as per previously identified centerline).

Using the door as support, shim the operator so that there is 3” (7.5cm) clearance between door and bottom of

operator. Tighten wall mounting bracket bolts.

9. For low ceiling applications, bolt operator direct to ceiling as shown in Fig G.

TROLLEY ARM INSTALLATION:

1. With door closed and trolley carriage positioned close to end of rails. align the mounting holes of straight arm and

curved arm so that pivot bolt on door bracket is in line with the top rollers of the door. Adjust length of 2-piece

trolley arm accordingly. Using suitable hardware, Align door bracket with centerline of door and secure to door using

suitable hardware.

10. For high ceiling applications, install hanging brackets (braces) from ceiling or structure to operator mounting plate.

3. At this time, check all bolts for tightness.

2. When properly installed the door arm should lean slightly away from door when door is fully closed.

THERE ARE 2 POSSIBLE ELECTRICAL CONTROL CONFIGURATIONS FOR THIS OPERATOR:

A) Full Feature logic board Smart 10.0 (UL325 (2010) compliant)with auxiliary apt board. Refer to Section A

for electrical connections and logic board instructions. Refer to electrical drawings inside your operator control

box or generic drawing MSL100APT-110V-3WM-WW, MSL300APT-WW and MSLC300APT-WW in the electrical

drawings section at the end of this manual.

B) High speed VFD option: Refer to section A as well as the separate diagrams and instructions located inside

control box

Refer to electrical diagrams inside control box cover or at the end of this manual prior to connection of power supply or

control station.

ELECTRICAL CONNECTIONS

IMPORTANT

- EACH INDIVIDUAL COMMERCIAL DOOR OPERATOR MUST HAVE IT’S OWN

DEDICATED POWER SUPPLY

- MICANAN HIGHLY RECOMMENDS THAT EACH INDIVIDUAL COMMERCIAL

DOOR OPERATOR HAVE AN EXTERNAL CIRCUIT BREAKER OR FUSED

DISCONNECT

WARNING

COMPARE AVAILABLE POWER SUPPLY VOLTAGE TO OPERATOR NAMEPLATE

PRIOR TO ELECTRICAL CONNECTION. FAILURE TO CONNECT APPROPRIATE

POWER SUPPLY VOLTAGE MAY CAUSE SERIOUS DAMAGE TO OPERATOR.

WARNING

TO REDUCE THE RISK OF INJURY OR DEATH:

ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A QUALIFIED

SERVICE PERSON

DO NOT ATTEMPT TO MAKE ELECTRICAL CONNECTIONS TO OPERATOR

UNLESS POWER SUPPLY HAS BEEN DISCONNECTED AT FUSE BOX

OPERATOR MUST BE CONNECTED IN ACCORDANCE TO LOCAL

ELECTRICAL CODES AND GROUNDED TO GREEN GROUND LUG LOCATED

INSIDE CONTROL BOX

Andere Micanan Türöffnungssystem Handbücher

Micanan

Micanan PRO-J Kurzanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Label

Label NEPTIS/LE Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Olide

Olide 120B Bedienungsanleitung

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung