MICODUS ML500G Bedienungsanleitung

ML500G User Manual V2.0

Learn how to set up your new MiCODUS Tracker

1. Main Features

2.Specifications

Real-time

Tracking

Corner

Uploading

Overspeed

Alarm

Vibration

Alarm

Geo-fence Teardown

Alarm

Temperature

Monitor

Historical Route

Playback

Powerful

Magnet

Waterproof

IP65

7-10 Days

Working Time

Voice

Monitor

mAh

5000

Low battery

alert

Shift

alert

Model

Weight

Dimensions

Charging Time

Battery Working Time

ML500G

172g

85mm(L) * 49mm(W) * 30mm(H)

Around 7 hours

Tracking Mode, 1 minutes’ reporting: 10 days

Device Information

Working Voltage

Working Current

Sleep Current

Battery Capacity

Working Temperature

Working Humidity

Working Frequency

SIM Card

Cellular Antenna

Positioning Type

GPS Antenna

Cold Start

Hot Start

Tracking sensitivity

GPS Channels

GPS+BEIDOU+LBS

Built-in

≤32 Seconds

≤1 Second

-162 dBm

4G LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66

2G GSM/GPRS/EDGE: 850/900/1800/1900MHz

Micro SIM Card

Built-in

DC 3.4V - 4.5V

4V/Average 45mA

4V/less than 5mA

3.7V 5000mAh Lion Polymer battery

-20℃- 75℃

10%-85%RH non-condensing

Working Parameters

Cellular Specifications

GNSS Specifications

Scope

Accuracy

Microphone, Light Sensor, Temperature Sensor

40℃to 125℃

±1℃

Temperature Sensor

External Interface

3. Activate Device

LED Event State

Charging

Charger inserted and battery has been fully charged

Charger has not been inserted

Searching for network

POWER LED (RED)

CELL LED

(YELLOW) Network has been registered

Solid

Dark

Flash every 1 second

Solid

GPS has fixed

GPS is in fixing Flash every 1 second

Device is working but stopped more than 5min

Device has not been turn on

Device ran out of battery

GPS LED (BLUE)

ALL LED

Solid

ALL LED TURN OFF

Install the SIM card via the correct direction as below:

APN,ApnName,User,

Password# SET APN OK APN,orange,

orange,orange#

APN,internet#SET APN OKAPN,ApnName#

SMS Command

Format Reply Example Note

If the SIM card has APN user and APN

password, then use this command.

If the SIM card operator doesn't have APN

user and APN password, then please use this

command.

Position Accuracy 5-10m

Normal SIM

Please get the exact correct APN name from local SIM card provider.Take the tracker

to a good signal place for operation and configure the APN for it as below:

Note: The APN information is very important, it must 100% correct to match with the sim card

of the tracker, if you conﬁgured wrong APN, the tracker also will reply "SET APN ok" but it will

can't get online!

4. Package Content

GPS Main Unit

USB Charging Cable

User Manual

Quick User Guide

Genuine Packing Box (Optional)

Hard-Wired Car Charger (Optional)

x 1

5. Functions Explanation

Please follow with the quick user guide carefully!

a. Working modes setting

* ML500G has 3 working modes to meet different tracking

demands, the setting command format is as below:

MODE,A,T1,T2#

* Example:

MODE,1,10,3600# (this means the device will upload data by 10s interval under moving

status and 3600s interval under stationary status)

MODE,2,0900,1# (this means the device will start working via mode 2 at 09:00am, and

it will upload data every 1 hour)

MODE,3,0900,1# (this means the device will start working via mode 3 at 09:00am, and

it will upload data every 1 hour)

A=1 (Tracking mode)

T1: upload interval of GPS data in moving status,

unit: second,10-3600s; default: 10s

T2: upload interval of GPS data in static status,

unit: second, 180-65535s; default: 3600s

A=2 (Power saving mode)

T1: interval start time,format: HH:MM

T2: time interval,range: 1-72

unit: hour,default interval: 24hours

A=3 (Hibernation mode)

T1: interval start time,format: HH:MM

T2: time interval,range: 1-72

unit: hour,default interval: 24hours

For example:

MODE,1,10,3600#

MODE,2,0900,1#

SET MODE OK

MODE,3,0900,1#

SET MODE OK

ML500G

* Note : The difference between mode 2 and mode 3 is that under mode 2

the device can be wake up by sms, call and vibration, under mode 3, the device will

just can be wake up by teardown alarm.

b. Voice Monitor:

* Set center number by this sms command:

CENTER,A,center number#

* Configure SOS numbers for the tracker by this sms com-

mand:SOS,A,1st number,2nd number,3rd number#

3 SOS numbers supports at the most

* Enable the device to enter into arm mode by this sms

command:ARM#

* Configure the alarm ways by this sms command:

TEARDOWN,A,M#

For example:

* Switch the tracker to voice monitor mode

by this sms command:MONITOR#

c. Vibration Alert:

This vibration alert function just work under stationary

status. How to use this function:

d. Tearndown Alert

* Enable the device to enter into arm mode by this

sms command: ARM#

* Conifgure the alarm ways by this sms command:

SENALM,[A][,M]#

A=ON/OFF, default: OFF;

M=0/1/2, way of alarming,

0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1

A=ON/OFF; default:ON

M=0/1/2; way of alarm,

0 : GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1

* Configure SOS numbers for the tracker by this sms

command:SOS,A,1st number,2nd number,3rd number#

3 SOS numbers supports at the most

* Keep the device under stationary status more than 5min to let it enter into sleep arm mode;

* Vibrate the device then the tracker will send the vibration alarm messages

* Dial the sim number of the tracker from the center

number, then the tracker will pick up the call automatically

and you will can remote monitor the voice around it.

CENTER,A,134********#

MONITOR#

SET CENTER NUMBER OK

SET MONITOR MODE OK

ML500G

For example:

SOS,A,134********#

SET SOS NUMBER OK

ARM#

SET ARM MODE OK

SENALM,ON,1#

SET VIBRATE ALARM OK

ML500G

For example:

SOS,A,134********#

SET SOS NUMBER OK

ARM#

SET ARM MODE OK

TEARDOWN,ON,1

SET TEARDOWN ALARM OK

ML500G

Unable to connect to

tracking platform

Check the APN and settings.

Check whrther the data service of SIM card is enabled.

Check the balance of SIM card.

Tracker shows offline

Check whether external power is still connected.

Check if the vehicle entered netword blind area.

Check the balance of SIM card.

6. Installation Recomendation

7. Troubleshooting

① Driving seat sundries box

② Front bumper

③ Door sundries box

④ Under the chassis

⑤ Rear windscreen

⑥ Rear bumper

Type Use

Location drift

In area with poor GNSS signal (tall building around or

basement), drifting may happen.

Check whether vibration happens around to trigger the

accelerator.

Unable to locate

Make sure the top side facing upward without metallic things

shielded.

Make sure it’s not in area with no satellite coverage.

No command reply

Make sure command format is correct.

Vehicle may be in network blind area.

Make sure SIM card is well inserted and has SMS servi.

Functions Command Format Explanation

8. Full SMS Commands List

APN Setting

Server Setting

If set with IP: SERVER,0,IP,Port#

APN,Network name[,name,password]#

If set with Domain Name: SERVER,1,

Domain,Port# SERVER,1,d.micodus.net,7700#

SERVER,0,47.254.77.28,7700#

A=old password, six digitals, digital range: 0-9,

default：000000;

B=new password, six digitals, digital range: 0-9

APN,CMNET# (if no name & Password)

APN,internet,internet,internet# (if with name

& Password)

Check IMEI IMEI#

Restore factory settings

Version Inquiry

Parameter Inquiry

Latitude&Longitude

Inquiry

Map URL Inquiry

Check All Alarms Status

FACTORY#

VERSION#

PARAM# Check ID,IMEI,APN, IP,PORT,TIMER,Center

number,SOS number,Time Zone

WHERE#

URL#

ALARM#

Revise the instruction

password PASSWORD,[A],[B]#

Status Inquiry STATUS#

BATTERY: XX% (Built-in Battery Power Percent)

NET: CLOSED (No Network) FAILED (Connecting

Network or Failure) SUCCESS(Connected

to Network),

NONE (No GSM Signal)

HIGH / MED / LOW (Signal Strength)

GPS: CLOSED (GPS Module Closed) FIXED,

N(Positioned and satellite number) UNFIX,

0 (Not Positioned yet)

TEMPERATURE: 30°C(the temperature around

the device)

ANGLE: 20 (the data upload angle)

SENSOR: ON/OFF (the status of the shake

sensor)

LEVEL: 3 (the sensitivity of the shake sensor)

STATE: ARM/DISARM (the defense status of

the device)

Time Zone Setting

Set the angle upload

ANGLEREP,[X][,A][,B]#

ANGLEREP,OFF#

GMT,Time zone orientation,Whole

Time Zone[,Half Time Zone]#

X=ON/OFF,default:ON; A=5~180 degrees,diversion

angle degree, default: 30 degrees;B=2~5 seconds,

detecting time, default: 3 seconds.

GMT,E,8# (if no half time zone)

GMT,W,9,30# (if has half time zone)

NOTE: Parameter : E / W; 0 ~ 12; 0/15/30/45

Add SOS Administr-

ator Number

Delete SOS

Administrator Number

Add Center Number

Delete Center Number

SOS,A,1st number,2nd number,3rd

number#

SOS,D,1st number,2nd number,3rd

number# or SOS,D,1,2,3#

CENTER,A,center number#

CENTER,A,13800138000#

NOTE: Only center number can be used

for cutting off fuel.

CENTER,D#

Set 3 numbers at a time:

SOS,A,13800138000,1380013800 1,13800138002#

Set the first numberseparately:

SOS,A,13800138000#

Set the second number separately:

SOS,A,,13800138001#

Means to set 3rd number separately:

SOS,A,,,13800138002#

Directly delete the number: SOS,D,13800138000#

Delete 1st number: SOS,D,1#

Delete 2nd number: SOS,D,2#

Delete the 2nd and 3rd number: SOS,D,2,3#

Query current mileage

A=ON/OFF, On/Off mileage calculation,

default: Off

B=0~999999, Mileage initial value , unit: km ;

default: 0, mileage return to zero

Mileage Statistics

MILEAGE,[A],[B]#

MILEAGE#

Functions Command Format Explanation

Working Mode Setting

A=1/2/3, 1:Tracking mode 2:Power saving mode

3:Hibernation mode; Default mode: 1

A=1

T1: upload interval of GPS data in moving status,

unit: second,10-3600s; default: 10s

T2: upload interval of GPS data in static status,

unit: second, 180-65535s; default: 3600s

A=2

T1: interval start time,format: HH:MM

T2: time interval,range: 1-72

unit: hour,default interval: 24hours

A=3

T1: interval start time,format: HH:MM

T2: time interval,range: 1-72

unit: hour,default interval: 24hours

MODE,A,T1,T2#

Sleep Mode Setting

Voice Monitor Mode

Track Mode

Heartbeat Packet

Upload

Sensor Sensitivity

MONITOR#

TRACK#

HBT,time#

MOTION,sensitivity#

SLEEP#

SLEEP,OFF#

NOTE: Before monitoring the voice around the device,

the user must change the device to this monitor mode

firstly.

NOTE: After used the voice monitor mode, user can

switch the device back to track mode by this command.

HBT,3#

NOTE: Range :1-60min, default 3min.

MOTION,2#

NOTE: Sensitivity Level：1-9 (1-9 is from week to

strong vibration)

NOTE: After set this sleep mode, the device will

enter into sleep mode automatically when the

device keep stationary status more than 5min.

Arm manually

Disarm manually

Overspeed Alarm

Setting

ARM#

DISARM#

SPEED,[A][,B][,C]#

SPEED,OFF#

Set the device into arm mode

Set the device out of arm mode

A=ON/OFF, open or close over speed alarm,

default：OFF

B=1～255(km/h), speed limit, default：100(km/h);

C=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS,

default：1.

Vibration Alarm

Setting

Shift Alarm

Setting

SENALM,[A][,M]#

SENALM,OFF#

SHIFT,[A][,B][,M]#

Example: SHIFT,ON,100,1# ( Means Setting 100

meters shift alarm range, when the ignition turned

off, vehicle’s 100 meters’ shift will trigger the alarm.)

A=ON/OFF; default:ON

B=Shift Distance (Range: 100-9999m)

M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+

GPRS, 2: GPRS+SMS+CALL, default:1

SHIFT,OFF#

A=ON/OFF, default: OFF;

M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+

GPRS, 2 : GPRS+SMS+phone call, default:2

Functions Command Format Explanation

E-mail: [email protected]

Skype: MiCODUS

9. Any Questions?

10. Download the APP

Download on the

APP Store

Download for

Android

Disassemble

Alarm Setting

Temperature

Alarm Setting

A=ON/OFF; default:ON

M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+

GPRS, 2: GPRS+SMS+CALL, default:1

);

)

℃~125℃

Example: TEMP,-1,50,2#

NOTE:

A: ON/OFF, Default: OFF

L: (LOW TEMPERATURE, Range:-40

H: (HIGH TEMPERATURE, Range:-40

M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS

+GPRS, 2 : GPRS+SMS+phone call, default:2

TEARDOWN,A,M#

TEARDOWN,OFF#

TEMP,ON,10,20,1#

TEMP,OFF#

Functions Command Format Explanation

BATALM, [A][, M]#

BATALM,OFF#

：ON; M=0/1, way of alarming,

A=ON/OFF, default

0: GPRS only, 1: SMS+GPRS, default：1；

Low Battery Alarm

Setting

Search "MiCODUS" in iOS APP store or Google Play

Store, or just scan the QR code as below to download

MiCODUS APP:

Inhaltsverzeichnis

Andere MICODUS GPS Handbücher

MICODUS

MICODUS MV720 Bedienungsanleitung

MICODUS

MICODUS ML150 Bedienungsanleitung

MICODUS

MICODUS MV790 Bedienungsanleitung

MICODUS

MICODUS MV33 Bedienungsanleitung

MICODUS

MICODUS MV730 Bedienungsanleitung

MICODUS

MICODUS MV930G 4G Bedienungsanleitung

MICODUS

MICODUS MP80G Bedienungsanleitung

MICODUS

MICODUS MV110 Bedienungsanleitung

MICODUS

MICODUS MV730G Bedienungsanleitung

MICODUS

MICODUS MV33 Bedienungsanleitung

MICODUS

MICODUS MV730 Bedienungsanleitung

MICODUS

MICODUS MV740 Bedienungsanleitung

MICODUS

MICODUS ML808G Bedienungsanleitung

MICODUS

MICODUS MV720 Bedienungsanleitung

MICODUS

MICODUS MV55G Bedienungsanleitung

MICODUS

MICODUS MV710G Bedienungsanleitung

MICODUS

MICODUS ML208G Bedienungsanleitung

MICODUS

MICODUS ML935 Bedienungsanleitung

MICODUS

MICODUS ML500 Bedienungsanleitung

MICODUS

MICODUS MV930 Bedienungsanleitung

MICODUS

MICODUS MV901 Bedienungsanleitung

MICODUS

MICODUS MV710G Bedienungsanleitung

MICODUS

MICODUS MV790G Bedienungsanleitung

MICODUS

MICODUS MV501G Bedienungsanleitung

Beliebte GPS Handbücher anderer Marken

Raven

Raven Cruizer II Handbuch

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung