Microlife BP W70 Bedienungsanleitung

Europe / Middle-East / Africa

Microlife AG

Espenstrasse 139

9443 Widnau, Switzerland

Tel. +41 71 727 7000

Fax. +41 71 727 7011

Email: [email protected]

www.microlife.com

Asia

Microlife Corporation

Tel. +886 2 8797 1288

Fax +886 2 8797 1283

Email: [email protected]

www.microlife.com

North / Central / South America

Microlife USA, Inc.

1617 Gulf to Bay Blvd

2nd Floor, Suite A

Clearwater, FL 33755, USA

Tel. +1 727 442 5353

Fax +1 727 442 5377

Email: [email protected]

www.microlife.com

IB BP W70 EN ROA 0922

BPW70

Wrist Blood Pressure Monitor

Microlife BP W70

AO-A

AO-B

AO-C

Microlife BP W70Guarantee Card

Name of Purchaser

Serial Number

Date of Purchase

Specialist Dealer

1BP W70 EN

Display

Microlife BP W70 EN

1ON/OFF button

2Display

3M-button (memory)

4Time Button

5Battery Compartment

6Cuff

7Systolic Value

8Diastolic Value

9Pulse Rate

AT Date/Time

AK Stored Value

AL Traffic Light Indicator

AM Pulse Arrhythmia Indicator (PAD)

AN Cuff Signal Indicator «ERR 1»

AO Cuff Fit Check

-A: Suboptimal Cuff Fit

-B: Arm Movement Indicator «ERR 2»

-C: Cuff Pressure Check «ERR 3»

AP Pulse Indicator

Battery Display

User Indicator

MAM Mode

Wrist Position Indicator

Keep dry

Type BF applied part

Intended use:

This oscillometric blood pressure monitor is a device intended to

measure the systolic and diastolic blood pressure and pulse rate of

an adult individual.

Dear Customer,

This device was developed in collaboration with physicians and

clinical tests carried out prove its measurement accuracy to be of a

very high standard.*

If you have any questions, problems or want to order spare parts

please contact your local Microlife-Customer Service. Your dealer

or pharmacy will be able to give you the address of the Microlife

dealer in your country. Alternatively, visit the internet at

www.microlife-asiapacific.com where you will find a wealth of

invaluable information on our products.

Stay healthy – Microlife AG!

* This device is tested according to the ESH protocol and ISO81060-2:2013.

Follow Instructions for Use. This document provides

important product operation and safety information

regarding this Blood Pressure Monitor. Please read this

document thoroughly before using the device and keep for

future reference.

Table of Contents

1. Using the Device for the First Time

• Inserting the batteries

• Selecting standard or MAM mode

• Selecting Wrist Position Indicator

• Setting the date and time

• Selecting the user

2. Checklist for Taking a Reliable Measurement

3. Taking a Blood Pressure Measurement

•How not to store a reading

• How do I evaluate my blood pressure?

•Appearance of the Pulse Arrhythmia Indicator (PAD)

4. Data Memory

•Viewing the stored values

• Memory full

•Clearing all values

5. Battery Indicator and Battery change

•Low battery

•Flat battery – replacement

• Which batteries and which procedure?

• Using rechargeable batteries

6. Error Messages

7. Safety, Care, Accuracy Test and Disposal

• Safety and protection

• Device care

• Cleaning the cuff

• Accuracy test

• Disposal

Guarantee

Technical Specifications

1. Using the Device for the First Time

Inserting the batteries

After you have unpacked your device, first insert the batteries. The

battery compartment

is on the bottom of the device. Insert the

batteries (

x 1.5 V, size

AAA

), thereby observing the indicated polarity.

Selecting standard or MAM mode

Before each measurement, select standard (single measurement) or

MAM mode (automatic double measurement). In MAM mode,

2 measurements are automatically taken in succession and the

result is then automatically analysed and displayed. Because the

blood pressure constantly fluctuates, a result obtained in this way

is more reliable than when a single measuremnt is performed.

• After the new batteries are fitted, Smart MAM mode ON/OFF

3BP W70 EN

selection will appear on the display first. Press the M-button to select

ON or OFF the MAM mode. Press the Time Button to confirm and

then select the Wrist Position Indicator. To change to standard mode

(single measurement), press the Time Button until the MAM mode

selection menu appears and select OFF.

• The bottom, right hand section of the display shows a 1 or 2 to

indicate which of the 2 measurements is currently being taken.

• There is a break of 15 seconds between the measurements. A count

down indicates the remaining time.

• The individual results are not displayed. Your blood pressure will only

be displayed after all 2 measurements are taken.

• Do not remove the cuff between measurements.

• If one of the individual measurements was questionable, an additional

measurement is automatically taken.

Selecting Wrist Position Indicator

Keeping the wrist at the same height level as heart during

measurement is one of the most important facts to use a wrist blood

pressure monitor. Incorrect wrist position might lead to an inaccurate

result. Follow the instruction of the Wrist Position Indicator to make sure

the wrist height is the same level as heart.

• After the MAM mode is selected, the Wrist Position Indicator ON/OFF

selection will appear on the display. Press the M-button to select ON

or OFF the Wrist Position Indicator. Press the Time Button to confirm

and then enter the date and time setting.

• There are 5 levels of height detection plus a blue LED indicator to

help the user determine if the monitor is at the correct height.

• When the monitor is at higher position relative to your heart, 1 or 2

downward arrow(s) appear to remind you to lower the wrist slowly

until the blue LED is lighted with a heart symbol. Conversely, 1 or 2

upward arrow(s) appear when your wrist height is lower to heart level

and raise the wrist higher as indication.

• Adjust your wrist to correct height level and keep about 2 sec, the

monitor will start measurement automatically.

• Please retain this wrist height during measurement, and do not move

even in the interval time of MAM mode until the result displayed on

the LCD.

• The blue LED will blank off during measurement to save the battery

power and appear again with the result when the measurement is

finished.

• If the user doesn’t adjust the wrist at correct heart level in time (about

9 sec), the monitor will still start measurement with upward/downward

arrows as an indication. However, we recommend to repeat the

measurement to make sure getting an accurate result.

Caution:

The Wrist Position Check is only an approximate indication,

and may not be accurate for all users because of differences in

individual physique and size. If you are unable to make your seat or

table adjustments and find the height of wrist is not same as your heart

level obviously, please turn off the Wrist Position Check feature and

position your wrist at heart level by yourself.

Setting the date and time

1. After selecting the Wrist Position Indicator, the year number

flashes in the display. You can set the year by pressing the

M-button3.to confirm and then set the month, press the time

button4.

2. Press the M-button to set the month. Press the time button to

confirm and then set the day.

3. Followthe instructions above to set the day, hour and minutes.

4. Once you have set the minutes and pressed the time button, the

date and time are set and the time is displayed.

5. If you want to change the date and time, press and hold the time

button down for approx. 3 seconds to enter setting menu. Press

time button twice to skip MAM mode/ Wrist Position

Indicator setting until the year number starts to flash. Now you

can enter the new values as described above.

Setting the user

This device allows to store the results for 2 individual users.

• Select the intended user (user 1 or user 2) by pressing the time

button.

Before each measurement, ensure that the correct user is

selected.

2. Checklist for Taking aReliable Measurement

Avoid activity, eating or smoking immediately before the measurement.

2. Sit down on a back-supported chair and relax for 5 minutes. Keep

the feet flat on the floor and do not cross your legs. Adjust your

seat height to make sure the distance between your seat and the

top of the table is within 30 ± 5 cm (12 ± 2 inches).

3. Always measure in a sitting position and on the same wrist. Use

the wrist which usually shows higher blood pressure values.

4. Remove any items of clothing and your watch, for example, so

that your wrist is free.

5. Always ensure that the cuff is positioned correctly.

6. Fit the cuff comfortably but not too tight. The cuff will cover a wrist

circumference of 13.5 – 21.5 cm (5.25 – 8.5 inches).

7. Support your arm in a relaxed position and ensure that the device

is at the same height as your heart.

3. Taking aBlood Pressure Measurement

2. Press the ON/OFF button 1to start the measurement.

1. Select standard (single measurement) or MAM mode (automatic

double measurement): see details in chapter«1».

After Wrist Position Indicator checked (see details in chapter

«1»), the cuff will now pump up automatically. Relax, do not move

and do not tense your arm muscles until the measurement result

BP W70 EN

4. The cuff fit check AO on the display indicates that the cuff is

perfectly placed. If the icon AO-A appears, the cuff is fitted subop-

timally, but it is still ok to measure.

5. The measurement is performed during the inflation. The inflation

speed may vary, this is a normal occurence.

6. During the measurement, the pulse indicator

flashes in the display.

7. The result, comprising the systolic 7and the diastolic 8blood

pressure and the pulse rate 9is displayed. Note also the expla-

nations on further display symbols in this booklet.

8. Remove and switch off the monitor. (The monitor does switch off

auto-matically after approx. 1 min.).

You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant pres-

sure sensation).

How not to store a reading

As soon as the reading is displayed press and hold the ON/OFF

button 1until «M» AK is flashing. Confirm to delete the reading by

pressing the time button 4.

«CL» is displayed when the reading is deleted from the

memory successfully.

How do I evaluate my blood pressure?

The triangle on the left-hand edge of the display

points at the range

within which the measured blood pressure value lies. The value is either

within the optimum (green), elevated (yellow) or high (red) range.

The classification corresponds to the following ranges defined by

international guidelines (ESH, ESC, JSH). Data in mmHg.

The higher value is the one that determines the evaluation. Example:

a blood pressure value of 140/80 mmHg or a value of 130/90 mmHg

indicates «blood pressure too high».

Appearance of the Pulse Arrhythmia (PAD)

This symbol AM indicates that certain pulse irregularities were

detected during the measurement. In this case, the result may

deviate from your normal blood pressure – repeat the measurement.

In most cases, this is no cause for concern. However, if the symbol

appears on a regular basis (e.g. several times a week with measure-

ments taken daily) we advise you to tell your doctor. Please show

your doctor the following explanation:

Range Systolic Diastolic Recommendation

1. blood pressure

too high

135 85 Seek medical

advice

2. blood pressure

elevated

130 - 134 80 - 84 Self-check

3. blood pressure

normal

<130 <80 Self-check

is displayed. Breathe normally and do not talk.

4. Data Memory

This model is designed for two users and can store up to 99 blood

pressure readings for each user.

Select either user 1 or 2 by pressing the time button.

Viewing the stored values

Press the M-button 3briefly, when the device is switched off. The

display first shows «M» AK and «A», which stands for the average of

all stored values.

Pressing the M-button again displays the previous value. Pressing the M-

button repeatedly enables you to move from one stored value to another.

Blood pressure readings with suboptimal cuff fit AO-A are not

considered in the average value.

Information for the doctor on frequent appearance of the

PAD symbol

This device is an oscillometric blood pressure monitor that also

analyses pulse irregularity during measurement. The device is

clinically tested.

The PAD symbol is displayed after the measurement, if pulse

irregularities occur during measurement. If the symbol appears

more frequently (e.g. several times per week on measurements

performed daily) we recommend the patient toseek medical

advice.

This device does not replace a cardiac examination, but serves

to detect pulse irregularities at an early stage.

Memory full

Pay attention that the maximum memory capacity of

memo-

ries is not exceeded.

When the

memory is full, the oldest

value is automatically overwritten with the

100th

value.

Values should be evaluated by a doctor before the memory

capacity is reached – otherwise data will be lost.

Clearing all values

If you are sure that you want to permanently remove all stored

Make sure the correct user is activated.

values, hold down the M-button (the device must have been switched

off beforehand) until «CL ALL» appears and then release the button.

To permanently clear the memory, press the time button while «CL

ALL» is flashing. Individual values cannot be cleared.

Cancel deletion:

press ON/OFF button

while «

CL ALL

» is

flashing.

5. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol AQ

will flash as soon as the device is switched on (partly filled battery

displayed). Although the device will continue to measure reliably, you

should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol AQ will flash as soon

as the device is switched on (flat battery displayed). You cannot take

any further measurements and must replace the batteries.

1. Open the battery compartment 5by pulling off the cap.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

3. To set date and time, follow the procedure described in «Section 1.».

The memory retains all values although date and time must be

reset – the year number therefore flashes automatically after

the batteries are replaced.

(after MAM mode and Wrist Position Indicator setting).

Which batteries and which procedure?

Use 2 new, long-life 1.5 V, size AAA alkaline batteries.

Do not use batteries beyond their date of expiry.

Remove batteries if the device is not going to be used for a

prolonged period.

Using rechargeable batteries

You can also operate this device using rechargeable batteries.

Only use «NiMH» type reusable batteries.

Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

device as they may become damaged (total discharge as a

result of low use of the device, even when switched off).

Always remove the rechargeable batteries if you do not

intend to use the device for a week or more.

Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

7BP W70 EN

7. Error Messages

If an error occurs during the measurement, the measurement is inter-

rupted and an error message, e.g. «ERR 3», is displayed.

Error Description Potential cause and remedy

ERR 1

Signal too

weak

The pulse signals on the cuff are too weak. Re-

position the cuff and repeat the measurement.*

ERR 2

Error signalDuring the measurement, error signals were

detectedby the cuff, caused for instance by

movementor muscle tension. Repeat the

measurement, keeping yourarm still.

ERR 3

No pressure

in the cuff

An adequate pressure cannot be generated in

the cuff. A leak may have occurred. Check that

thecuff is correctly connected and is not too

loose.Replace the batteries if necessary.

Repeat the measurement.

» Pulse or cuff

ERR 6

»MAM Mode

error

ERR

Wrist Position

Indicator error

pressure too

high

The pressure in the cuff is too high (over

299 mmHg) OR the pulse is too high (over

199 beats per minute). Relax for 5 minutes

and repeat the measurement.*

» Pulse too

lowThe pulse is too low (less than 40 beatsper

minute). Repeat the measurement.*

Error Description Potential cause and remedy

ERR 5

» Abnormal

result

The measuring signals are inaccurate and no

result can therefore be displayed. Read through

the checklist for performing reliable measure-

ments and then repeat the measurement.*

There were too many errors during the

measurement in MAM mode, making it

impossible to obtain a final result. Read

through the checklist for performing reliable

measurements and then repeat the

measurement.*

Possibly some problem occurs on the sensor

for Wrist Position Indicator. Turn off and

remove the battery then repeat measurement.

If still displayed, please contact your local

Microlife-Service.

* Please immediately consult your doctor, if this or any other

problem occurs repeatedly.

If you think the results are unusual, please read through the

information in «Section 1.» carefully.

Inhaltsverzeichnis

Andere Microlife Blutdruckmessgerät Handbücher

Microlife

Microlife BP A100 Bedienungsanleitung

Microlife

Microlife BP 3BTO-1 Bedienungsanleitung

Microlife

Microlife BP AG1-20 Bedienungsanleitung

Microlife

Microlife MAM Easy BP A3 Easy Bedienungsanleitung

Microlife

Microlife WatchBP Home Bedienungsanleitung

Microlife

Microlife BP A2 Classic Bedienungsanleitung

Microlife

Microlife WatchBP Home Bedienungsanleitung

Microlife

Microlife BP A3 PLUS Bedienungsanleitung

Microlife

Microlife BP A130 Bedienungsanleitung

Microlife

Microlife BP 3SZ1-1 Bedienungsanleitung

Microlife

Microlife WatchBP Office Vascular Bedienungsanleitung

Microlife

Microlife W3 Comfort Bedienungsanleitung

Microlife

Microlife BP A130 Bedienungsanleitung

Microlife

Microlife Premier Automatic Blood Pressure Monitor Bedienungsanleitung

Microlife

Microlife BP A2 Classic Bedienungsanleitung

Microlife

Microlife BP W100 Bedienungsanleitung

Microlife

Microlife BP W1 Basic Bedienungsanleitung

Microlife

Microlife BP W90 Bedienungsanleitung

Microlife

Microlife aponorm Bedienungsanleitung

Microlife

Microlife BP 3AQ1 Bedienungsanleitung

Microlife

Microlife WatchBP Home Bedienungsanleitung

Microlife

Microlife BP A1 Easy Bedienungsanleitung

Microlife

Microlife BP W100 Bedienungsanleitung

Microlife

Microlife WatchBP office Bedienungsanleitung

Beliebte Blutdruckmessgerät Handbücher anderer Marken

Little Doctor

Little Doctor LD7 Bedienungsanleitung

Omron

Omron M6W Handbuch

Mx Onda

Mx Onda MX-CP2395 Bedienungsanleitung

Braun

Braun VitalScan 1 Bedienungsanleitung

Little Doctor

Little Doctor LD-91 Bedienungsanleitung

Sanitas

Sanitas SBM 09 Bedienungsanleitung

A&D

A&D LifeSource UB-328 Bedienungsanleitung

König Electronic

König Electronic HC-BLDPRESS200 Bedienerhandbuch

Leicke

Leicke Sharon Bedienungsanleitung

Omron

Omron M6 Comfort Bedienungsanleitung

3B SCIENTIFIC

3B SCIENTIFIC U11395 Bedienungsanleitung

Soehnle

Soehnle SYSTO MONITOR 100 Bedienungsanleitung

Nasco Healthcare

Nasco Healthcare Simulaids Life/form LF01095U Referenzhandbuch

HoMedics

HoMedics MiBody 360 Bedienungsanleitung

ForaCare

ForaCare FORA P30 Plus Bedienungsanleitung

JOYTECH

JOYTECH DBP-6296B Bedienungsanleitung

Omron

Omron Silver BP5250 Bedienungsanleitung

visomat

visomat double comfort Bedienungsanleitung