Microtek Bio-5000 Bedienungsanleitung

Install Software

Start Here

Installing your Microtek Bio-5000

Important: Do not remove the yellow sticker from your

scanner until you are told to do so. You must install

software before connecting your scanner.

Always close any open programs, and turn off Anti-virus

utilities before installing software.

Unpack Contents

Unpack your scanner package and

check for major components.

1. Bio-5000 scanner

2. Hi-Speed USB cable

3. Power code

4. Vinyl Strips

5. Software CDs

6. Leak-Free Glass Holder (2 pcs)

I49-004654 E, September 2013

A. Place the Adobe CD-ROM into the CD-ROM drive, and install the software. Skip this step if you

have a newer version of Photoshop Elements already installed on your computer.

B. Place the Microtek software CD-ROM into the CD-ROM drive, and follow the on-screen

instructions to install the driver and software.

NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the

following in succession: “My Computer”; the CD-ROM icon; then cdsetup.exe to start the installer

program.

C. Restart your computer at the end of all software installation.

LEAK-FREE GLASS HOLDER

Thisholder is specifically designed for 

theuse of the gel and transparent film scanning.

LEAK-FREE GLASS HOLDER

Thisholder is specifically designed for 

theuseof the gel and transparent film scanning.

Unlock Scanner

A. Remove the yellow “Unlock” sticker from your digitizer.

B. With the scanner power off, tilt the front right corner of

the scanner to see the locking screw at the bottom.

C. Using a screwdriver, push and turn the locking screw

counterclockwise to the unlock position. When

successfully unlocked, the screw will push out a little,

protruding slightly from the bottom of the scanner.

Connect Scanner

To the power adapter

A. Connect the power cord to the back of the

scanner.

B. Plug the power cord into a power source.

To the Hi-Speed USB cable

C. Connect one end of the cable to your computer.

D. Connect the other end of the cable to the scanner.

E. Press the power button at the front panel of your scanner,

and wait for the lights to stop blinking and stay on steady.

The system will detect your

scanner automatically.

Power button

NOTE: To lock the scanner (for shipping and other reasons),

refer to the Bio-5000 Supplement.

Position the Scan Material

Position the Electrophoresis Gels

To scan the electrophoresis gels, use

the Leak-Free Glass Holder. Place the

electrophoresis gel to be scanned on

top of the Leak-Free Glass Holder and

then insert the Leak-Free Glass Holder

into the lower compartment

(transparency bay) of the scanner.

Make sure the Leak-Free Glass Holder

is inserted correct side up.

LEAK-FREE GLASS HOLDER

Thisholder is specifically designed for 

theuse of the gel and transparent film scanning.

Calibration strip

(Keep clear and unobstructed)

The correct side up is the side showing

the holder labels facing up

LEAK-FREE GLASS HOLDER

Thisholder is specifically designed for 

theuse of the gel and transparent film scanning.

Calibration strip

(Keep clear and unobstructed)

The correct side up is the side showing

the holder labels facing up

To scan transparent film, use the

Leak-Free Glass Holder. Place the

film to be scanned face down on top

of the Leak-Free Glass Holder.

Secure the film to the glass surface if

needed with the vinyl strips provided,

and insert the Leak-Free Glass Holder

into the lower compartment

(transparency bay) of the scanner.

Make sure the Leak-Free Glass Holder

is inserted correct side up.

Position Reflective Materials

To scan reflective materials such as photos: Raise

the scanner lid, and place the original to be

scanned face down on the scanner glass bed,

towards the front of the scanner. Center the top

of the original along the horizontal ruler of the

scanner. Close the lid, and prepare to scan.

Position Transparencies

Please take note that the high temperature may cause the damage to your electrophoresis gels,

transparencies and reflective materials. Therefore, remember to turn off the scanner and remove the

scanned materials from the scanner once you finish the scan job.

Position the Scan Material (cont.)

ScanWizard Bio

ScanWizard Bio is the scanner controller software for the Bio-5000. The four windows of

ScanWizard Bio are shown here to familiarize you with the interface and to prepare you for the

material in the next section on “Scanning.” ScanWizard Bio can be launched as a stand-alone by

clicking the program icon, or it can be launched by using the File-Import or File-Acquire command

from your image-editing program.

Preview window when

scanning photos (reflectives)

Preview window when

scanning transparencies

Preview window when

scanning electrophoresis gels

Info window

Scan Job Queue window

Settings window

How to Scan: Scanning Electrophoresis Gels,

Transparencies, and Reflectives

Scanning Electrophoresis Gels

1. Position the electrophoresis gel on top of the Leak-Free Glass Holder, as detailed in the “Position

the Scan Material” section of the Start Here guide.

2. Launch ScanWizard Bio.

3. In the Preview window of ScanWizard Bio, choose Positive Film from the Scan Material menu.

4. Click the Overview button in the Preview window to see a preliminary scan of the image.

5. Select the Scan Frame tool, and choose the area to be scanned by sizing the marquee around the

targeted area.

6. Select the Auto Focus tool, and select the area of the scan frame to which the AF function will be

applied.

7. Specify your scanning requirements in the Settings window. Choose the desired image type and

resolution, and adjust the scan frame settings if necessary.

8. Adjust image quality if necessary, using the Advanced Image Correction tools.

9. Click the Scan (or “Scan to”) button in the Preview window to start scanning. (The Scan button

appears as the “Scan to” button when ScanWizard Bio is launched in stand-alone mode in

Windows XP.)

Scanning Transparent Film

1. Select the film you wish to scan, then follow the procedures for positioning transparent film

detailed in the “Position the Scan Material” section of the Start Here guide.

2. Launch ScanWizard Bio.

3. In the Preview window of ScanWizard Bio, choose Positive Film or Negative Film from the Scan

Material menu depending on the types of the film to be scanned.

4. Follow steps 4 to 8 of the procedures detailed in “Scanning Electrophoresis Gels” (the first

column in this section).

5. To complete the scan, click the Scan (or “Scan to”) button in the Preview window to start

scanning.

How to Scan: Scanning Electrophoresis Gels, Transparencies, and Reflectives (cont.)

Scanning Reflective Originals (e.g., photos or prints)

1. Position the reflective originals on the upper glass bed, as detailed in the “Position the Scan

Material” section of the Start Here guide.

2. Launch ScanWizard Bio.

3. In the Preview window of ScanWizard Bio, choose Reflective from the Scan Material menu.

4. Click the Overview button in the Preview window to see a preliminary scan of the image.

5. Select the Scan Frame tool, and choose the area to be scanned by sizing the marquee around the

targeted area.

6. Specify your scanning requirements in the Settings window. Choose the desired image type and

resolution, and adjust the scan frame settings if necessary.

7. Adjust image quality if necessary, using the Advanced Image Correction tools.

8. Click the Scan (or “Scan to”) button in the Preview window to start scanning. (The Scan button

appears as the “Scan to” button when ScanWizard Bio is launched in stand-alone mode in

Windows XP.)

How to Scan: Scanning Electrophoresis Gels, Transparencies, and Reflectives (cont.)

Problems?

The orange and green LEDs on the front of the

scanner indicate the status of the scanner. On

power up, you should see the following:

First, make sure that you have followed installation steps 1 through 4. If your problem is listed here,

try the suggested solution.

1. No light comes on when the scanner is turned on.

Make sure your scanner is connected to your computer and plugged into a power source.

2. Add/Remove Hardware Wizard appears on your screen.

Click the “Cancel” button and close the Control Panel. Disconnect the USB cable from the back of

your computer, and refer to the installation instructions in this guide.

3. When trying to scan, an error message appears on your screen that reads, “Can’t Find Scanners”.

Make sure your scanner is unlocked (see Step 3).

Make sure your scanner is connected to your computer and plugged into a power source (see Step 4).

Uninstall and reinstall the ScanWizard Bio software.

4. After clicking scan, a blank screen appears.

Make sure your scanner is unlocked (see Step 3).

Uninstall and reinstall the ScanWizard Bio software.

5. Having trouble scanning negatives or slides?

Make sure that you have properly inserted the Leak-Free Glass Holder, as indicated in the “Position

Electrophoresis Gels” and “Position Transparencies” sections of the Start Here guide.

From the Preview window of ScanWizard Bio, choose Positive or Negative from the Scan Material

menu.

Make sure that the calibration strip is unobstructed. For location of the calibration strip, see the

“Position the Scan Material” section of the Start Here guide.

Uninstall and reinstall the ScanWizard Bio software.

All Off - Scanner is off

Flashing Orange - Warming up

All On - Ready to scan LEDs

DoYou Need Assistance?

Manuals

If you have additional questions and need further instruction or information, we provide electronic

manuals for:

1. Using your Bio-5000 (Supplementary information)

2. Using the ScanWizard Bio scanning software

3. Using the bundled third-party software

To access the electronic manuals: Insert the scanner’s software CD-ROM into your computer’s CD-

ROM drive. Next, locate and click the “Manuals” option when the software installer window appears

on your screen. Finally, select and click the title of the manual you wish to view.

Missing Items

If your package is missing items, please call Microtek Customer Service.

Drivers & Software Upgrades

After you finish the installation of software, if you found that the installed drivers and software cannot

run your product or your computer system properly later, please go to the Microtek Download Service

site at ww7.microtek.com.tw/service.php to download and install any updates you may require.

For additional information about Microtek products, please visit our website at www.microtek.com.

ColoRescue are trademarks or registered trademarks of Microtek International,

Inc. All other trademarks or registered trademarks are the property of their

respective holders. Specifications, software and hardware bundles are subject

to change without notice. Delivery of technical support services subject to

change without notice. Not responsible for typographical errors.

Andere Handbücher für Bio-5000

Inhaltsverzeichnis

Andere Microtek Scanner Handbücher

Microtek

Microtek ArtixScan 2500 Bedienungsanleitung

Microtek

Microtek ArtixScan F1 Bedienungsanleitung

Microtek

Microtek ScanMaker V6UPL Bedienungsanleitung

Microtek

Microtek ScanMaker V6UPL Bedienungsanleitung

Microtek

Microtek ScanMaker 4 Bedienungsanleitung

Microtek

Microtek ScanMaker 6000 Handbuch

Microtek

Microtek ScanMaker 3740 Handbuch

Microtek

Microtek ADF-700 Bedienungsanleitung

Microtek

Microtek ScanMaker i900 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 2020 Bedienungsanleitung

Microtek

Microtek ArtixScanDI 6240S Bedienungsanleitung

Microtek

Microtek ArtixScan DI 6260S Bedienungsanleitung

Microtek

Microtek Bio-5050 Bedienungsanleitung

Microtek

Microtek ObjectScan 1600 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 3130c Bedienungsanleitung

Microtek

Microtek ArtixScan DI 2015c Bedienungsanleitung

Microtek

Microtek ScanMaker s430 Bedienungsanleitung

Microtek

Microtek LightLid 35 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 5230 Bedienungsanleitung

Microtek

Microtek XT6060 Bedienungsanleitung

Microtek

Microtek ArtixScan 1800f Bedienungsanleitung

Microtek

Microtek ScanMaker 1000XL Plus Bedienungsanleitung

Microtek

Microtek ArtixScan 1200DF Bedienungsanleitung

Microtek

Microtek Vantas 3100 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung