MikroTik hAP ax lite LTE6 Bedienungsanleitung
hAP ax lite LTE6
hAP ax lite LTE6, L41G-2axD&FG621-EA
Safety Warnings
Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for
preventing accidents. The installer should be familiar with network structures, terms, and concepts.
Use only the power supply and accessories approved by the manufacturer, which can be found in the original packaging of this product.
This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making sure, that
the Installation of the equipment is compliant with local and national electrical codes. Do not attempt to disassemble, repair, or modify the device.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power adapter from the power outlet.
The adapter shall be installed near the equipment and shall be easily accessible.
Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the European Union radiation exposure limits set forth for an uncontrolled
environment. This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the general public.
Quickstart
Please follow these quick steps to set up your device:
Connect your computer to one of the Ethernet ports;
Configure your computer to obtain its IP address automatically through DHCP;
Insert a micro SIM card into the slot;
1.
2.
3.
4.
5.
6.
Connect the power adapter to the DC jack;
To initiate the configuration, access in your web browser;https://192.168.88.1
The username is "admin" and there is no password (or, for some models, check user and wireless passwords on the sticker);
Update the device by clicking the (Check_for_updates) on the right side and updating your RouterOS software to the latest version. Must have a
valid SIM card inserted;
For a manual update of the device, visit ;https://mikrotik.com/download
Select the v7 ARM-packages (routeros-arm-x.x.npk, wifiwave2-arm-x.x.npk) for this device and download them onto your PC;
Upload downloaded packages to the (WebFig) (Files) menu and reboot the device. By upgrading your RouterOS software to the latest version,
you can ensure optimal performance, stability, and security updates;
In the (QuickSet) menu, set up the following: Choose your country, to apply country regulation settings;
Set up your wireless network password in the left field;
Set up your router password in the bottom field.
MikroTik mobile app
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.
Scan the QR code and choose your preferred OS.
Install and open the application.
By default, the IP address and user name will be already entered.
Click Connect to establish a connection to your device through a wireless network.
Choose Quick Setup and the application will guide you through all basic configuration settings in a couple of easy steps.
An advanced menu is available to fully configure all necessary settings.
Powering
The device accepts power in the following ways:
USB type C accepts 5 V DC.
The power consumption under maximum load can reach 12 W.
Configuration
Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version
ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to
conform with local regulations.
RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to
the possibilities: . In case an IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC https://mt.lv/help https://mt.lv/winbox
address of the device from the LAN side (all access is blocked from the Internet port by default).
For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and Jumpers
Mounting
The device is designed to be used indoors and placed on a flat surface with all needed cables connecting to the front of the unit.
The IP rating scale of this device is IP20. We recommend using Cat6 shielded cables.
Warning! This equipment should be installed and operated with a minimum distance of 20 cm between the device and your body. Operation of this
equipment in the residential environment could cause radio interference.
Expansion slots and ports
Product code L41G-2axD&FG621-EA
CPU Dual-Core IPQ-5010
CPU architecture ARM
Size of RAM 256 MB
Storage 128 MB, NAND
Number of 1G Ethernet ports 4
Switch chip model MT7531BE
Wireless band 2.4 GHz
Wireless interface model IPQ-5010
Wireless 802.11b/g/n/ax dual-chain
Wireless antenna max gain 4.3 dBi
Antenna header count 2
LTE category 6 (300Mbit/s Downlink, 50Mbit/s Uplink)
LTE modem FG621-EA
TAC 86335904
LTE FDD bands 1 (2100MHz) / 3 (1800MHz) / 5 (850MHz) / 7 (2600MHz) / 8 (900 MHz) / 20 (800MHz) / 28 (700MHz)
3G Category R8 (42.2Mbps Downlink, 11.2Mbps Uplink)
3G Bands 1 (2100MHz) / 3 (1800MHz) / 5 (850MHz) / 8 (900MHz)
Dimensions 124 x 100 x 54 mm
Operating system RouterOS v7, License level 4
Operating temperature -40°C to +60°C
Reset button
RouterBOOT reset button has the following functions. Press the button and apply the power, then:
Release the button when the green LED starts flashing, to reset the RouterOS configuration to defaults.
Keep holding for 5 more seconds, the LED turns solid, release now to turn on CAPs mode (total 10 seconds).
Release the button after the LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers (required for reinstalling RouterOS
over the network).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Accessories
The package includes the following accessories that come with the device:
5V 2.4A 12W USB power adapter
Operating system support
The device supports RouterOS software version 7. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.
To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in
designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated
disposal sites in your area.
Andere Handbücher für hAP ax lite LTE6
1
Inhaltsverzeichnis
Andere MikroTik Netzwerk-Hardware Handbücher
MikroTik
MikroTik RouterBOARD 411R Bedienungsanleitung
MikroTik
MikroTik G16-a-LHGR kit Series Bedienungsanleitung
MikroTik
MikroTik LHG Lite60 Bedienungsanleitung
MikroTik
MikroTik netPower 15FR Bedienungsanleitung
MikroTik
MikroTik CCR2004-16G-2S+PC Bedienungsanleitung
MikroTik
MikroTik RB5009UPr+S+IN Bedienungsanleitung
MikroTik
MikroTik RBMetalG-52SHPacn Bedienungsanleitung
MikroTik
MikroTik RouterBOARD 750G Bedienungsanleitung
MikroTik
MikroTik RBLDF-5nD Bedienungsanleitung
MikroTik
MikroTik SXT R Bedienungsanleitung
MikroTik
MikroTik CRS310-1G-5S-4S Plus OUT Bedienungsanleitung
MikroTik
MikroTik Chateau 5G ax Bedienungsanleitung
MikroTik
MikroTik RouterBOARD 450 Series Bedienungsanleitung
MikroTik
MikroTik RAY60 Bedienungsanleitung
MikroTik
MikroTik LHGGM&EG18-EA Bedienungsanleitung
MikroTik
MikroTik LHG LTE18 kit Bedienungsanleitung
MikroTik
MikroTik RouterBOARD Groove 2Hn Bedienungsanleitung
MikroTik
MikroTik nRAY Series Bedienungsanleitung
MikroTik
MikroTik FiberBox Plus Bedienungsanleitung
MikroTik
MikroTik ATL LTE18 kit Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
