MikroTik NetMetal ac2 Series Bedienungsanleitung

NetMetal ac²

Quickstart

The configuration is the same as PTP Bridge in AP mode, except that wireless mode is set to ap_bridge for PTMP setups. The router can be accessed

directly using MAC address. If the device is connected to the network with enabled DHCP server, configured DHCP client on the bridge interface will get

the IP address, that can be used to access the router.

Please follow these quick steps to set up your device:

Open the upper cover (see " ");NetMetal ac²#Removing upper and bottom covers

Connect an external antenna to the SMA connector (see " ");NetMetal ac²#Antenna usage

Open the bottom cover (see " ");NetMetal ac²#Removing upper and bottom covers

Connect your PC with Ethernet cable to the Ethernet port of the device, or connect your ISP cable to the device.

Connect the device to the power source (see " ");NetMetal ac²#Powering

Open network connections on your PC and search for MikroTik wireless network and connect to it;

The configuration can be done through the wireless network usinga WinBox configuration tool ;http://mt.lv/winbox

Once connected to the wireless network, open Winbox and click on the "Neighbors" to find the device.

Click on the MAC address, user name: admin and there is no password, click Connect.

Please update the device to the latest version,use the "Check for updates" button if you are connected to the ISP and have an active internet

connection. If you are connecting to the device using Winbox, please go https://mikrotik.com/download

Choose ARM packages for this device and download to your PC.

Upload downloaded packages to the Winbox "Files" menu and reboot the device.

Updatingyour RouterOS software to the latest version will ensure the best performance, stability, and security updates.

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.

Depending on the antenna used, you must set its gain in the RouterOS software to ensure that EIRP meets the limit set by the local authorities.

This is done in the Wireless menu;

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time.

Click on the "Apply Configuration" to save changes.

Powering

The device accepts power in the following ways:

Ethernet port accepts PoE 802.3af/at 24-57 V DC ;

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter;

Connect an Ethernet cable from your local network (LAN) to the PoE adapter;

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

Scan QR code and choose your preferred OS.

Install and open application.

By default, the IP address and user name will be already entered.

Click Connect to establish a connection to your device through a wireless network.

Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps.

An advanced menu is available to fully configure all necessary settings.

Removing upper and bottom covers

To remove the upper cover, unscrew two captive screws and slide it off the main body. Do not remove screws completely, when assembling

tightening torque 0.2 Nm.

To remove the bottom cover, release clips for both fasteners and cover will be free to open.

Mounting

The NetMetal ac2 is designed to be used outdoors and mounted on pole or DIN rail.

When mounting, please ensure that cable feed is pointing downwards.

The IP rating scale of this device is IP55. We recommend using Cat6 shielded cables.

Warning! This equipment should be installed and operated with a minimum distance of 20 cm between the device and your body. Operation of this

equipment in the residential environment could cause radio interference.

Mounting and configuration of this device should be done by a qualified person.

The mounting hose clamp is provided with the package.

Guide hose clamp through the opening on the back of the device.

Attach to the pole or mast.

Align and secure by hose clamp screw using PH2 screwdriver.

The device should be always placed by TOP cover facing upwards.

When mounting on DIN rail, please find a special bracket in the package and secure it with four screws to the back of the unit.

With the attached mounting bracket you will be able to slide the device on the DIN rail.

Grounding

The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded. The device includes a grounding wire attachment

screw. Attach your grounding wire to the grounding screw, then attach the other end of the grounding wire to the grounded mast.

Please secure all loose Ethernet cables and antenna cables to the pole or mast approximately 30cm from the device, so that the cable weight is not pulling

the ports and connectors.

Front status LED behavior

RouterOS allows configuring each LED's activity the way that the user wishes. It is possible to configure the LEDs to display wireless strength, blink the

LEDs on interface traffic activity and many other options. For further information please visit https://wiki.mikrotik.com/wiki/Manual:System/LEDS

Default factory configuration for this device:

Solid Blue – The device is powered on.

Solid Green – Active SFP port.

Solid Green – Active Ethernet port.

- 8. Solid Green – The set of five green LEDs, shows the signal strength.

Configuration

The device is configured as a wireless access point, with the Ethernet port configured as a DHCP client, for connecting to your ISP router or switch. A

DHCP server is configured on the wireless interface.

We recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version ensures the best

performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to conform with local

regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of http://mt.lv/help http://mt.lv/winbox

the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device for reinstallation, see a section Reset button.

Expansion slots and ports

Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for

connecting to other network devices.

SFP port.

External SMA antenna connectors.

MiniPCIe slot.

Integrated Wireless module operating at 2.4 GHz, 802.11b/g/n protocol.

Integrated Wireless module operating at 5 GHz, 802.11a/n/ac protocol.

USB type-A.

Reset button

The reset button has three functions:

Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10

seconds).

Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15

seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Accessories

Package includes the following accessories that come with the device:

EU Switching Power Supply 48 V 0.95 A 45.6 W.

Gigabit POE injector.

K-27 DIN rail bracket mounting set.

Hose clamp 40/60 w2 A2 9 mm.

Please visit wiki pages for MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

MiniPCIe slot usage

This NetMetal version is without modem installed. To install the module you will need to remove the upper cover and open bottom cover (see "NetMetal

"). Installing a miniPCIe module should be done by a qualified person, please follow safety precautions when ac²#Removing upper and bottom covers

handling electrical equipment:

Use a wrist grounding strap when unpacking and working with electrical components to avoid electrical discharge (ESD) damage.

Removing four screws using the PH2 screwdriver.

Remove the top cover by lifting it.

Locate the miniPCIe slot on the PCB and remove two factory attached screws.

Attach provided a thick thermal pad to the card, and install the card into miniPCIe slot so that the thermal pad is between PCB and card.

The secure card in place using previously removed two screws.

Attach the grey uFL connector to the MAIN antenna connector of the modem, attach the black cable to the secondary (or AUX) connector.

Attach a thinner thermal pad to the top of the card.

Drill a hole for cables using a 6.5 mm drill to provide an opening for card antenna cables.

Guide through the card cables.

Reassemble.

When assembling make sure the rubber sealing is placed firmly around the case for equal spread to prevent water contamination. Case screw torque 2,5

Nm.

When mounting the antenna for the installed card, please make sure to keep them separate at a good distance from Wireless antennas.

Antenna usage

Antenna Installation. WARNING: It is the installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC

rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly

forbidden in accordance with FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country

regulations and per antenna type. Professional installation is required for equipment with connectors to ensure compliance with health and safety issues.

LIST OF :APPROVED 2GHz ANTENNAS

5 dBi Dipole ACOMNIRPSMA

LIST OF APPROVED 5GHz ANTENNAS:

30 dBi Parabolic dish MTAD-5G-30D3

19 dBi Sector MTAS-5G-19D120

Antennas of the same type and lower gain than those listed above may be used in compliance with certification.

More information on the wireless interface: https://wiki.mikrotik.com/wiki/Manual:Interface/Wireless

Specifications

For more information about this product, specifications, pictures, downloads and test results please visit our web page: https://mikrotik.com/product

/NetMetal_ac2

Operating system support

The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be mounted on a pole. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct

hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

Read the installation instructions before connecting the system to the power source.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Andere Handbücher für NetMetal ac2 Series

Inhaltsverzeichnis

Andere MikroTik Drahtloser Zugangspunkt Handbücher

MikroTik

MikroTik SXTG-5HPacD Bedienungsanleitung

MikroTik

MikroTik RouterBOARD Groove 52HPn Bedienungsanleitung

MikroTik

MikroTik LHG XL 52 ac Bedienungsanleitung

MikroTik

MikroTik PWR-LINE AP Bedienungsanleitung

MikroTik

MikroTik LHG Series Bedienungsanleitung

MikroTik

MikroTik OmniTIK 5 Bedienungsanleitung

MikroTik

MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung

MikroTik

MikroTik wAP 60G Series Bedienungsanleitung

MikroTik

MikroTik RBSXTsq5nD Bedienungsanleitung

MikroTik

MikroTik NetMetal ac Series Bedienungsanleitung

MikroTik

MikroTik Wireless Wire Cube Bedienungsanleitung

MikroTik

MikroTik mAP 2nD Bedienungsanleitung

MikroTik

MikroTik RB931-2nD Bedienungsanleitung

MikroTik

MikroTik SXTG-5HPacD-HG Bedienungsanleitung

MikroTik

MikroTik LtAP LR8 LTE kit Bedienungsanleitung

MikroTik

MikroTik cAP Leitfaden

MikroTik

MikroTik RouterBOARD wAP R Bedienungsanleitung

MikroTik

MikroTik LHG 60G Bedienungsanleitung

MikroTik

MikroTik Cube 60G ac Bedienungsanleitung

MikroTik

MikroTik Cube Lite60 Series Bedienungsanleitung

MikroTik

MikroTik wAP ac RBwAPG-5HacD2HnD Bedienungsanleitung

MikroTik

MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung

MikroTik

MikroTik LHG 2 Bedienungsanleitung

MikroTik

MikroTik wAP series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung