Milwaukee MC110 Bedienungsanleitung

SPECIFICATIONS:

MC110 MC120 MC122

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

SETPOINT 3.5 to 7.5 pH 5.5 to 9.5 pH

ALARM active when measure is

higher/lower than selected setpoint

depending on user selection

OUTPUT POWER SOCKET active when measure is

(for MC122 only) higher/lower than selected setpoint (5A max)

depending on user selection

POWER DRIVERS 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

(for MC122 only)

pH ELECTRODE MA911B/2 (included)

ENVIRONMENT 0 to 50°C, 95% RH not condensing

POWER SUPPLY 12 VDC (included)

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT MC110, MC120 160 g (meter only)

MC122 180 g

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 20 ml sachet (25 pcs)

WARRANTY:

These instruments are warranted from all defects in materials and manufacturing for a

period of two years from the date of purchase. The electrode is warranted for a period

of 6 months.

If during this period, the repair or replacement of parts is required, where the damage is

not due to negligence or erroneous operation by the user, please return the parts to

either dealer or our office and the repair will be effected free of charge.

Note: We reserve the right to modify the design, construction and appearance of ourproducts without

advance notice.

MANUAL

PORTABLE pH METER

MODELS: MC110 -MC120 -MC122

OPERATION

• Connect the supplied 12VDC power

adapter to the meter and to the

mains line.

• Connect the pH-electrode to the

BNC socket on the bottom of the

meter.

• Always remove the electrode

protective cap before taking any

measurement. If the electrode has

been left dry, soak the tip (bottom

2.5 cm) in M10000B rinse solution

for a few minutes to reactivate it 12VDC O" RELAY OUTPUT

12VDC pH RELAY

ADAPTER ELECTRODE OUTPUT

• Make sure that the meter has been calibrated before taking any

measurements (see Calibration Procedure).

• Immerse the tip (2.5 cm) of the pH-electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize and the meter will start continuous

monitoring.

• A blinking alarm will indicate when the measured pH value is higher or

lower than selected setpoint, depending on user selection.

NOTE.The output power contact (MC122 only) has no protection fuse

inside the meter. It is recommended to protected it outside, against

failure.

SETPOINT

The setpoint can be selected by

adjusting the central front knob to the

desired value.

• The selectable range is from 3.5 to

7.5 pH for MC110; from 5.5 to 9.5 pH

for MC120 and MC122.

• The nature of the setpoint can be

selected by setting the switch to the

desired position (ABOVE or BELOW).

CALIBRATION PROCEDURE

•Remove the protective cap from the electrode.

•Immerse the electrode tip into a new sachet of pH 7

calibration solution and allow the reading to stabilize.

•Adjust the pH7 calibration trimmer (on the front) to

display "7.0 pH".

•Open a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

•Immerse the electrode tip into the pH 4 sachet and

allow the reading to stabilize.

•Adjust the pH4/10 calibration trimmer (on the front) to

display "4.0 pH".

•The calibration is now complete and the meter is

ready to take measurements.

•It is suggested to recalibrate the meter at least

once a month, after a prolonged stocking time

and after pH-electrode replacement.

INSTALLA TION PROCEDURE

(for MC122 only) :

Dieses Handbuch passt für folgende Modelle

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee L4 CLLP Bedienungsanleitung

Milwaukee

Milwaukee MW150 Bedienungsanleitung

Milwaukee

Milwaukee CALIBRATION 2238-20 Betriebsanleitung

Milwaukee

Milwaukee MR32ATC Bedienungsanleitung

Milwaukee

Milwaukee CALIBRATION 2238-20 Bedienungsanleitung

Milwaukee

Milwaukee MW100 Bedienungsanleitung

Milwaukee

Milwaukee Smart Monitoring System SMS110 Bedienungsanleitung

Milwaukee

Milwaukee 48-22-9802 Bedienungsanleitung

Milwaukee

Milwaukee REDSTICK MLDIG14 Bedienungsanleitung

Milwaukee

Milwaukee M12 3PLA Bedienungsanleitung

Milwaukee

Milwaukee 2309-60 Bedienungsanleitung

Milwaukee

Milwaukee 48-22-9801 Bedienungsanleitung

Milwaukee

Milwaukee M12 SPL Bedienungsanleitung

Milwaukee

Milwaukee MC125 Bedienungsanleitung

Milwaukee

Milwaukee HEAVY DUTY 7,5 m LED Tape Measure Bedienungsanleitung

Milwaukee

Milwaukee MI412 Bedienungsanleitung

Milwaukee

Milwaukee MAX MW160 Bedienungsanleitung

Milwaukee

Milwaukee EC40 Bedienungsanleitung

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee MC125 Bedienungsanleitung

Milwaukee

Milwaukee MW100 Bedienungsanleitung

Milwaukee

Milwaukee 4933478101 Bedienungsanleitung

Milwaukee

Milwaukee 3421 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung