Milwaukee Mi451 Bedienungsanleitung

www.milwaukeetesters.com

Milwaukee Wine Lab Photometer

Mi451

Copper

INSTRUCTION MANUAL

Instruction Manual Mi451 COPPER Photometer for wine analysis

FUNCTIONAL DESCRIPTION ............................................................................... 3

GENERAL DESCRIPTION ..................................................................................... 4

SPECIFICATIONS ............................................................................................... 6

GUIDE TO DISPLAY CODES ................................................................................. 7

GENERAL TIPS FOR AN ACCURATE MEASUREMENT ................................................. 8

MEASUREMENT PROCEDURE ............................................................................. 10

ERROR MESSAGES ........................................................................................... 13

BATTERY REPLACEMENT .................................................................................... 14

ACCESSORIES ................................................................................................. 14

TABLE OF CONTENTS

www.milwaukeetesters.com

FUNCTIONALDESCRIPTION

FRONT PANEL

A. LID

B. CUVET HOLDER

C. LIQUID CRYSTAL DISPLAY (LCD)

D. ON/OFF KEY, TO TURN THE METER ON AND

OFF

E. ZERO KEY, TO START THE ZERO MEASUREMENT

F. READ KEY, TO START THE SAMPLE MEASUREMENT

G. TIMER KEY, TO ACTIVATE THE COUNTDOWN

MODE TIMER

DISPLAY

A. BATTERY STATUS ICON

B. HOURGLASS ICON

C. LAMP STATUS INDICATOR

D. MEASURE STATUS

E. MEASUREMENT UNIT

F. MAIN DISPLAY

G. PARAMETER NUMBER INDICATOR

H. TIMER MODE INDICATOR

I. SECONDARY DISPLAY

Instruction Manual Mi451 COPPER Photometer for wine analysis

GENERAL DESCRIPTION

Thank you for choosing Milwaukee. This instruction manual will provide you the necessary

information for correct use of the meter.

Mi451 is an auto-diagnostic portable microprocessor meter. It has an advanced optical

system based on a special tungsten lamp and a narrow band interference filter that allows

most accurate and repeatable readings. All instruments are factory calibrated.

The auto-diagnostic feature of this meter ensures always optimal measurement conditions

to perform most precise readings. The light level is automatically adjusted each time a

zero-measurement is made, and the temperature of the lamp is controlled to avoid

overheating.

SIGNIFICANCE OF USE

Grapes accumulate normally only a small amount of copper by natural translocation from

roots. Unless exposed to significant airborne pollution or vineyard sprays, increased

concentrations in wine result from contamination during post-fermentation processing,

like contact with non stainless steel equipment and as impurities in fining agents and filter

media.

The copper concentration in wine is normally low, less than 0.10 to 0.30 mg/L, because

excess copper is precipitated during fermentation due to adsorption onto the yeast cells.

This adsorption and precipitation can reduce the initial copper concentration with 40 to

89%. At higher concentration copper plays an important role in catalysing oxidation reac-

tions of wine phenols.

It is important to check the copper content both in must and in wine, because at levels

above 9 mg/L copper becomes a metabolic toxin that inhibits or delays alcoholic

fermentation, and concentrations exceeding 1 mg/L may be sensorial detected and should

be avoided.

Other copper related problems can be manifested as formation of white haze (in white

wines) and later as a reddish-brown amorphous precipitate. This precipitated ‘casse’

develops only under the strongly reducing conditions found in bottled wines. It has been

found that this casse is a mixture of copper compounds and proteins.

www.milwaukeetesters.com

Factors favouring and inhibiting copper casse formulation in wine

Necessary conditions Preventive

for copper case formation Measures

strong reducing conditions copper levels at less than 0.3 mg/L

low iron concentrations limit SO2addition

high protein levels cold-stabilize and bentonite fine to reduce

proteins in white wine

light and heat

This meter is supplied with:

• Two sample cuvets and caps

• Reagents for 20 tests (Mi551A-0, Mi551B-0, Mi551C-0, Mi551D-0)

• Two 20 ml vials with caps

• Two 1 ml plastic pipettes

• Two 3 ml plastic pipettes

• Two spoons

• Four 1.5V AA batteries

• Tissue for wiping cuvets

• Instruction Manual

• Instrument Quality Certificate

Instruction Manual Mi451 COPPER Photometer for wine analysis

This instrument is in compliance with CE Directives.

SPECIFICATIONS

Range 0.00 to 1.50 mg/L

Resolution 0.05 mg/L

Precision SD±0.05 mg/L @ 0.50 mg/L

Light Source Tungsten lamp

Light Detector Silicon Photocell with narrow band interference filter @ 560 nm

Method The reaction between Copper and the reagents causes a purple tint in

the sample.

Environment 0 to 50 °C (32 to 122 °F) ; max 95% RH non-condensing

Battery Type 4 x 1,5 volt AA batteries

Auto-Shut off After 15' of non-use in measurement mode.

Dimensions 225 x 85 x 80 mm (8.7 x 3.3 x 3.1")

Weight 500 g (17,6 oz.).

Required Reagents

Code Description Quantity/test

Mi551A-0 Copper Reagent A 5 mL

Mi551B-0 Copper Reagent B 5 mL

Mi551C-0 Copper Reagent C 2 x 4 spoons

Mi551D-0 Copper Reagent D 2 x 4 spoons

www.milwaukeetesters.com

PROBE FUNCTIONAL DESCRIPTIONPROBE FUNCTIONAL DESCRIPTION

PROBE FUNCTIONAL DESCRIPTION

GUIDE TO DISPLAY CODES

After Timer is pressed, a blinking hourglass icon appears

and the display shows a 10 minutes coundown. At the

end of the countdown an acoustic signal alerts the user

that the timer is finished.

Indicates that the instrument is in a ready state and

waiting for the next command (Timer or Zero).

This prompt indicates the battery capacity value.

This prompt appears for a few seconds each time the

instrument is turned ON.

The instrument is zeroed and a measurement can be

made.

Indicates that the meter is performing a zero

measurement. The light intensity is automatically re-

adjusted (auto-calibration features) if necessary.

Indicates that the meter is making a measurement.

Batteries voltage is getting low and the batteries need

to be replaced.

Instruction Manual Mi451 COPPER Photometer for wine analysis

Indicates that the batteries are dead and must be

replaced. After this message appears, the instrument

is switched off. Change the batteries and restart the

meter.

GENERAL TIPS FOR AN ACCURATE MEASUREMENT

The instructions listed below should be carefully followed during testing to ensure

best accuracy.

• Use the supplied plastic pipette for adding the exact amount

of wine sample (15 mL) or reagents A or B (up to the 20 mL

mark) to the graduated glass vials. The liquid in the vial

forms a convexity on the top; the bottom of this convexity

must be at the same level of the mark.

• To transfer the supernatant organic solvent from the vials to

the cuvets use two different clean 1 mL pipettes, one for the zero and one for the

sample.

a) squeeze the bulb of the pipette;

b) insert the plastic pipette into the supernatant organic solvent and release the

bulb slowly, paying attention not to transfer the wine sample too;

c) fill a cuvet with organic solvent by squeezing the bulb of the pipette.

www.milwaukeetesters.com

•Diluting procedure of the wine sample in case the “L Lo” (Low

Light) message appears: use the pipette to fill the glass vials with

5 mL of wine sample, then fill the vials up to the 15 mL mark with

Mi550S1-0. This is the diluted wine sample. The final reading

must be multiplied by 3 to compensate for dilution.

• In order to avoid reagent leaking and to obtain more accurate

measurements, it is recommended to close the cuvet first with the

supplied HDPE plastic stopper and then with the black cap.

• Whenever the cuvet is placed into the measurement cell, it must

be dry outside, and completely free of fingerprints, oil or dirt.

Wipe it thoroughly with Mi0004 (tissue for wiping cuvets, see

chapter ACCESSORIES) or a lint-free cloth prior to insertion.

• Do not let the reacted sample stand too long after extraction,

or accuracy will be lost.

• It is possible to take multiple readings in a row, but it is

important to take a new zero reading for each different wine-

sample. Use always a fresh prepared zero for making the zero

reading.

• After the reading it is important to discard immediately the sample, otherwise the glass

might become permanently stained.

• All the reaction times reported in this manual are referred to 20°C (68°F). As a general

rule of thumb, they should be doubled at 10°C (50°F) and halved at 30°C (86°F).

Repeat step a), b) and c) until all the organic solvent is transferred. Ensure that at least 1/

3 of the cuvet is filled with organic solvent, otherwise erroneous results will be obtained.

Notes:

- If some wine sample is transferred too, this does not interferes with the method.

- Try to avoid transferring suspended solids that might be present.

- If necessary, air bubbles can be removed tapping the vials gently on the table.

Instruction Manual Mi451 COPPER Photometer for wine analysis

1010

MEASUREMENT PROCEDURE

• Turn the instrument on by pressing ON/OFF.

• When the LCD displays “----”, it is ready.

• Use the 3 mL plastic pipette to fill two glass vials

with 15 mL of wine sample (up to the mark).

Note: The liquid in the vial forms a convexity

on the top; the bottom of this convexity must

be at the same level of the mark.

• Use a clean 1 mL pipette to add 5 ml of

Reagent A

(Mi551A-0) to the first vial (A).

• Use the second 1 mL pipette to add 5 ml of

Reagent B (Mi551B-0) to the second vial (B).

• Add 4 full spoons of reagent C (Mi551C-0)

each vial.

• Using the other supplied spoon, add 4 full spoons

of Reagent

D (Mi551D-0) to each vial.

• Close the glass vials tightly with their caps and

shake both vials vigorously for 1 minute.

Note: block the cap with a finger during shaking!

• Press TIMER and the instrument will show the

countdown or, alternatively, wait for 10 minutes,

leaving the vials capped and undisturbed.

During this period the color of the upper layer

(organic phase) in vial B will turn purple if

copper is present.

After 10 minutes the instrument gives an

acoustic signal to alert the user that the

countdown is finished.

Inhaltsverzeichnis

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee 2235-20 Bedienungsanleitung

Milwaukee

Milwaukee MW105 MAX Bedienungsanleitung

Milwaukee

Milwaukee MA882 Bedienungsanleitung

Milwaukee

Milwaukee MI413 PRO Bedienungsanleitung

Milwaukee

Milwaukee MA886 Bedienungsanleitung

Milwaukee

Milwaukee 2205-20 Bedienungsanleitung

Milwaukee

Milwaukee 2280-20 Bedienungsanleitung

Milwaukee

Milwaukee MW700 Bedienungsanleitung

Milwaukee

Milwaukee 2217-40 Bedienungsanleitung

Milwaukee

Milwaukee MW101 Bedienungsanleitung

Milwaukee

Milwaukee CALIBRATION 2238-20 Bedienungsanleitung

Milwaukee

Milwaukee Heavy Duty 2270-20 Bedienungsanleitung

Milwaukee

Milwaukee 3631-20 Bedienungsanleitung

Milwaukee

Milwaukee LDM 30 Bedienungsanleitung

Milwaukee

Milwaukee PST MW100 PRO Bedienungsanleitung

Milwaukee

Milwaukee M12 SPL Bedienungsanleitung

Milwaukee

Milwaukee MW13 Bedienungsanleitung

Milwaukee

Milwaukee MC110 Bedienungsanleitung

Milwaukee

Milwaukee LDM 80 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM L4 3PL Bedienungsanleitung

Milwaukee

Milwaukee SM500 Bedienungsanleitung

Milwaukee

Milwaukee MC510 Bedienungsanleitung

Milwaukee

Milwaukee MI407 Bedienungsanleitung

Milwaukee

Milwaukee MW10 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung