Thank you very much for your purchase of the JFX200-2513 optional ionizer.
Please read this manual and fully understand it before using the device. If you have any question, contact your local distributor.
For note and safety, refer to the instruction manual of JFX200-2513 main body.
Before using, be sure to read “Warning and Note” of this manual and fully understand its contents.
It is recommended to check the effect of removing electricity in advance.
At normal printing (printing from operation panel side to Y bar waiting side)
After setting the media, make the machine “REMOTE”status and print from RasterLink.
The function to remove electricity operates and it prints the media while removing electricity of it.
At reverse printing (printing from Y bar waiting side to operation panel side)
[FUNCTION] - [VIEW] - - [SET VIEW POS 1610mm], move the Y bar.
Set the media setting.
[FUNCTION] - [VIEW] - - [SET VIEW POS 0mm], move the Y bar.
[FUNCTION] - [VIEW] - - [SET VIEW POS 1610mm], move the Y bar.
During that time, the function to remove electricity operates and electricity of the media is removed.
Make the machine “REMOTE”status and print from RasterLink.
Check the electrode probe before the work and clean it if it is dirty.
Method for daily care
1. Remove the electrode probe from the ionizer.
By using the attached electrode probe replacement kit, you can remove it easily.
2. Wipe off the electrode probe and around it with a cotton swab immersed
in alcohol.
Recommended: ethyl alcohol, isopropyl alcohol
When it is very dirty
Use an ultrasonic bath.
Also, you can use alcohol as washing liquid.
Note
After cleaning, fully dry it and then attach it to the ionizer to use.
When washing liquid remains on the electrode probe, it may cause an accident or failure of the machine.
Before using
• It is possible that enough effect cannot be achieved depending on your using environment or the
media.
How to use
• While the Y bar is moving, fully be careful about your body or things not to hit it.
Daily care
• Before taking care of it, be sure to turn off the main power switch of the main body.
You may get an electric shock. Also, you may get injured collaterally.
• Do not touch the electrode probe directly. You may get injured. Be careful to work.
Instruction Manual for Ionizer
This ionizer has the function to output alarms.
Alarm output part
Alarm function
Alarm output function
Item Alarm (ALM) Ion level (ION) Condition (COND)
Indication Indicator light blinks three
times about every second.
Indicator light blinks twice
about every second.
Indicator light blinks. once
about every second
Status etc.
Internal circuit has been
broken.
Abnormal discharge occurs.
Due to blot on the electrode
probe and wear of it, ion
production has decreased.
Use this as a guide for time to
take care of the electrode probe.
The installed environment
(temperature, humidity,
peripheral metals, etc.) have
affected the performance to
remove electricity.
Removing
electricity
Removing electricity stops. Removing electricity continues. Removing electricity continues.
Countermeas
ure
Contact a distributor in your
district or our office.
Take care of the electrode
probe.
*1
If the status cannot be
improved, replace the relevant
electrode probe.
*1. Before taking care of the electrode probe, turn off the main power of the main body, and be careful to
perform the work.
Check the environment and
peripheral metals.
Replacement
part －
SPA-0208
Tungsten electrode probes for
ionizer (including 4)
－
Warning and Note
• High voltage is applied. Prevent it from water, oil, flammable solvent, etc. being poured. Other-
wise, breakdown occurs or it may cause an electric shock and failure of the machine.
• Do not put metals, your body, your finger, etc. closer to it. It may cause an electric shock and
failure of the machine.
• There is a danger that generated ozone may do something detrimental to you if the machine is
used in the close place. When you use the machine in the close place, be sure to ventilate.
• Do not use in a place where the temperature changes significantly or dew condensation occurs.
• Before maintaining or taking care of it, be sure to turn off the main power of the main body.
• When taking care of it, do not touch the electrode probe directly.
• Should an abnormality is found, contact a distributor in your district or our office. Do not repair
the machine by the customer. It may cause an electric shock and failure of the machine.
• Do not touch the electrode probe with a hard thing such as a tool. It may cause an accident or
failure of the machine.
• Due to prolonged use, dust/ ink adhere to the electrode probe and it becomes dirty. If you keep
using it as it is, the machine cannot produce the performance to remove electricity enough, and
it may cause an accident or failure of the machine. Be sure to take care of it.
• Do not use this for any purpose other than eliminating static electricity.
