MINOURA B60 Bedienungsanleitung
Indoor Bicycle Trainer – instructions manual
Minoura Japan Headquarters Minoura North American Tech Center
(for all customers) (for U.S. residents only)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A.
Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899
www.minoura.jp
Made in Japan
B60-D (Non-Remote)
B60-R (Remote)
Read this instructions carefully before use
Tire Size Capacity Range<w/o Z-adaptor> 26 x 1.0 – 700 x 45c
<with Z-adaptor> 22 x 1-3/8 – 700 x 32c
(ver.1.0 2010/5)
(Shown image: B60-D)
IMPORTANT NOTICE
• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.
• Fits tire size between 26x1.0 and 700x45c. 29-inch is not compatible on this model.
To use 26x1.0" or smaller tire, install the optional Z-shaped Small Wheel Adaptor.
• Some assembly required. Use correct tools (10mm spanner & M4 hex wrench). Tools
are not supplied in the kit.
• Use the supplied rear quick release skewer for maximum stability.
Minoura is not responsible for any problem caused from using your own skewer.
(* Quick release skewer = A wheel axle device which allows mounting/disengaging the
wheel without any tool)
• If your bike wheel is not equiped with a quick release skewer but a standard hub nut
type axle, remove the black plastic Grommet (F-9) from the Right Side Coupling (F-1)
for better and safer tting.
Be sure that it is not possible to convert a hub nut type wheel axle to a quick rekease
skewer type unless replacing the wheel hub itself.
• Use on at and level oor or ground for your safety.
• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.
Tire-to-roller contact will eventually wear both your tire and the trainer roller. It's
normal.
• On B60-D (non-remote type), adjusting the resistance must be done when the bike
stopped. Do not operate the Dial Lever (EM-13) for changing the resistance power
while the rear wheel is spinning.
• Touching the spinning wheel and/or any other moving parts while training should
cause serious injury. Keep children and pets away from the trainer when in use.
• If you feel any strange noise or smell, stop using B60 immediately and contact the
retailer where you purchased.
• Any warranty will be void if you use B60 for other purpose than instructed.
Minorua offers 1-year limited warranty on the resistance unit and 5-year limited
warranty on the frame from the date of your purchase for any problem caused by
manufacturer's defect.
Any damage or problem caused by transporting process is not covered under warranty.
Any damage from shipping or moving must be made to the shipping company.
Read enclosed "Minoura Limited Warranty Policy" card for more detail.
- Page 2 -
F-1: Coupling (Right)
F-4: Coupling Cover
F-7: Hub Handle
F-9: Grommet
BF-5: Leg Rubber Cover (White)
BF-6: Leg Rubber
BF-9: B60 Main Frame (Black)
M5-2: Rubber Foot Cap (29mm)
MF-3: Micro Adjust Knob Set
B60 Schematics
BF-9
BF-5
BF-6 M5-2
MF-3
F-7
F-4
F-9
F-1
EM-1 EM-2
EM-3 EM-4
EM-5 EM-6 EM-17
EM-8
EM-9
EM-10
EM-1 EM-2
EM-3 EM-4
EM-5
EM-12
EM-13
EM-17
EM-8
EM-11
LM-10
<B60-D Non-Remote>
<B60-R Remote>
EM-1: Outer Cap EM-10: Cable Guide
EM-2: Axle Holder EM-11: Connecting Plate
EM-3: Drive Roller & Bearing EM-12: Magnet Plate (Dial)
EM-4: Main Housing EM-13: Dial Lever
EM-5: Alloy Plate EM-17: Flywheel (600g)
EM-6: Magnet Plate (Remote) GM-19: Remote Shifter
EM-8: Flywheel Cover LM-10: Base Plate
EM-9: Remote Base
- Page 3 -
BF-5
BF-6
GM-19
3. Fully open both legs and place B60 on a at and
level oor.
At this moment, make sure all 4 foot are
contacting the oor at once to sit on the oor
stable. (see Fig. B)
How To Setup Your B60 Trainer
2. Install the Roller Pressure Adjust Knob set (MF-3)
to the welded nut on the B60 frame. (see Fig. A)
- Page 4 -
1. Replace your rear wheel quick release skewer to the supplied one.
Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape.
!
If your bike is not equipped with quick release skewer and it's a hub nut type, you
should remove the black plastic Grommet (Skewer Nut Protector) (F-9) from the
right side coupling. Minoura doesn't guarantee the stability if you don't remove the
Grommet
You don't need the supplied quick release skewer if your wheel is a hub nut type.
It's not possible to convert your wheel from the hub nut type to the quick release
skewer type unless replacing the hub.
!
Required Tools: 1 x 10mm Spanner
1 x M4 Hex Wrench
!
Make sure the acorn shaped spring
direction is as shown in Fig. A.
Failure will cause difculty on rotating.
(Fig. A)
(Fig. B)
4. Place your rear wheel in between the couplings.
1) Turn the Hub Handle in the direction of
counter-clockwise to make the enough space
between the couplings.
You should almost fully open the coupling
for easier wheel installation. (see Fig. C)
2) Insert the left side (quick lever side) skewer into the left side coupling rst.
The quick lever shaft must be inserted into the cut-out on the coupling to hold the bike stable. Turn the
coupling to adjust the cut-out position prior to tightening the Hub Handle.
3) While keeping this position, slowly come down the bike to align the right side acorn nut to the right
side coupling.
4) Turn the Hub Handle clockwise to hold the rear wheel.
Once the rear wheel hub is stify caught between the couplings and you see the frame starts opening,
it's the bottom position. Stop tightening.
6) Turn the Hub Handle two more rotations. Do not try to over-tighten the Hub Handle.
Both right and left side couplings are
designed to suit the supplied quick release
skewer. The left side coupling must t
perfectly in the skewer head to get correct
stability. (see Fig. D)
Any skewer type which lever is located on
the end of the axle (see Fig. E) or the lever
will not be bent over right angle (see Fig. F)
cannot be used on B60.
!
(Fig. D)
(Fig. E) (Fig. F)
!
Do not try to over-tighten the Hub Handle
to keep the correct thightness of rear hub
clamping.
Too tight setting will cause damage to both
B60 and your bike frame.
Too loose setting may cause the bike to
come out of the trainer during use.
- Page 5 -
(Fig. C)
!
Be careful not to over-loosen the
Hub Handle. It will loosen the
inside nut and no longer proper
tightening can be expected.
6. The rear tire should sit in the almost center part of
the Drive Roller without touching any other parts.
(see Fig. I)
If the tire has touched the plastic parts (see Fig. K)
due to some reasons like the rear wheel is not trued
correctly or you have installed a too fat tire, you must
adjust the Mag unit position.
To do so, loosen the backside screws with M5 hex
wrench, adjust the roller position, then tighten the
screws again tightly. (see Fig. J)
5. Contact the Drive Roller to the rear tire by turning the Roller Pressure Adjust Knob clockwise. (see Fig. G)
The best position is that the roller compresses the tire in the depth of 3 - 4 mm. (see Fig. H)
- Page 6 -
(Fig. I)
(Fig. K)(Fig. J)
!
If the rear tire has touched any other parts than the Drive Roller, the certain part
should be damaged and your tire will wear out quickly.
(Fig. G) (Fig. H)
Please note too much and too less roller pressure will bring premature tire wear.
Keep correct roller pressure and maintain the air pressure in correct level before
using B60.
!
If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.
TIPS
How To Adjust Resistance Level (B60-D)
B60-D provides 3 different resistance levels to suit your
training level.
To Increase Resistance Level:
Slide the Dial Lever toward "H" position.
To Decrease Resistance Level:
Slide the Dial Lever toward "L" position.
5. To remove the bike from B60, loosen the micro adjust knob rst, then loosen the Hub Handle.
If you remove the bike without changing the roller position, the next installation may become difcult
because the rear wheel has been pushed forward by the roller.
- Page 7 -
1. Wind the band around the handlebar or stem, and hook the metal ring to the gutter on the remote shifter
base. (see Fig. M-1)
3. The soft fabric band is pre-adjusted to t normal 22mm diameter handlebar.
If you need to mount onto an oversized or specially shaped handlebar or stem, adjust the band (see Fig. N).
At this moment, we suggest you to slide the guide pin downward (see the column) to loosen the band for
easier work.
121
23
B60-R features a convenient remote shifter lever. You can install it on the handlebar or stem, then you can
control the resistance power in 7 levels without necessary of getting off the bike.
Decrease
Increase
(Fig. M)
(Fig. N)
(Fig. O)
2. Flip up the lever to lock (see Fig. M-2). If it is loosened, adjust the band tighter as per instructed in the
following section.
4. To increase the resistance, twist the lever toward "H". To decrease the resistance, twist the lever towawrd
"L". (see Fig. O)
You can choose from 7 different levels to suit your desired workout level.
How To Adjust Resistance Level (B60-R)
(Fig. L)
If you wish to use the tire sized 26x1.0" or smaller,
you need to install the optional Z-shaped "Small
Wheel Adapter" between Base Plate and Mag unit to
raise up the roller height.
The direction of Z-adapter is xed so follow the
arrow printed on the top and make sure it's pointing
toward the front (toward your bike).
If the drive roller cannot reach the tire even if you
install the adaptor, make sure you have been installed
in correct direction.
Use the original cap head bolts for the Base Plate,
and use the supplied hex head bolts for the Mag unit.
How To Use Small Wheel Adaptor (Option)
Hex Head Bolt
Cap Head Bolt
Z-Adaptor
< in case of V270 >
Required Tools: 1 x 10mm Spanner
1 x M5 Hex Wrench
- Page 8 -
Why My Remote Shifter Doesn't Work Properly?
You may have a shifting problem that you cannot set at L
or H position properly due to the lengthened inner cable.
To x this problem, follow the steps to adjust the initial
cable tension.
1. Set your remote shifter at "H" position and remove
the shifter from your handlebar, then straighten the
cable as much as possible.
2. Pull out the plastic cover cap on foot of the remote
cable. (see Fig. P and Q)
3. Hold the inside adjusting screw and push it toward
the shifter, then adjust the locking nut to set the
cable tension properly. (see Fig. R)
4. Install the cover cap again.
(Fig. P)
(Fig. Q)
(Fig. R)
(Fig. S)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere MINOURA Heimtrainer Handbücher
MINOURA
MINOURA M60-D Bedienungsanleitung
MINOURA
MINOURA Minimag M20-D Bedienungsanleitung
MINOURA
MINOURA B60-D Bedienungsanleitung
MINOURA
MINOURA LiveRide LR340 Bedienungsanleitung
MINOURA
MINOURA MAG-850 Bedienungsanleitung
MINOURA
MINOURA FG540 HYBRID ROLLER Bedienungsanleitung
MINOURA
MINOURA LiveRide LR341 Bedienungsanleitung
MINOURA
MINOURA MAG-850 Bedienungsanleitung
MINOURA
MINOURA LiveRoll R720 Bedienungsanleitung
MINOURA
MINOURA MAG-500 Series Bedienungsanleitung
MINOURA
MINOURA VFSG-9 Bedienungsanleitung
MINOURA
MINOURA LiveRide LR960 Bedienungsanleitung
MINOURA
MINOURA MAG-850LW Series Bedienungsanleitung
MINOURA
MINOURA SmartTurbo KAGURA LSD9200 Bedienungsanleitung
MINOURA
MINOURA SmartTurbo Kagura EHT1020 Bedienungsanleitung
MINOURA
MINOURA V270 Bedienungsanleitung
MINOURA
MINOURA VFS150 Bedienungsanleitung
MINOURA
MINOURA LiveRide LR961 Bedienungsanleitung
MINOURA
MINOURA LiveRide FG220 Bedienungsanleitung
MINOURA
MINOURA VFS3R - SCHEMATICS Bedienungsanleitung
Beliebte Heimtrainer Handbücher anderer Marken
Stamina
Stamina 1310 Bedienungsanleitung
American Fitness
American Fitness SPR-BK1072A Bedienungsanleitung
Cateye
Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung
BH FITNESS
BH FITNESS H9158H Bedienerhandbuch
Body Sculpture
Body Sculpture BC-7220G Bedienungsanleitung
Cateye
Cateye EC-2300 Bedienungsanleitung
