Minuteman C37115-13 Bedienungsanleitung

SINGLE MOTOR UPRIGHT

VACUUM CLEANER

MODEL C37115-13

■OPERATION

■SERVICE

■PARTS

■CARE

MPV13 VACUUM CLEANER

Instruction Manual

-1-

CONTENT

Important safety instructions………………..…..2

Technical specification…………………………..2

How to assemble……………………………….. 3

How to use……………………………………….4

Maintenance……………………………………..6

Problem solving…………………………………9

Exploded view…………………………………..10

When using the MPV13 vacuum cleaner, basic precautions always be followed, including following:

READ ALL INSTRUCTIONS BEFORE USING

VACUUM CLEANER

WARNING-To reduce the risk of fire, electric shock or injury:

1. Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before

servicing.

2. Do not use outdoors or on wet surfaces.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in this manual. Use only manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If the appliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped into water, return it to a service center.

6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp

edges or corners. Do not run the appliance over cord. Keep cord away from heated surface.

7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

8. Do not handle plug or vacuum cleaner with wet hands.

9. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce airflow.

10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

11. Turn off all controls before unplugging.

-2-

12. Use extra care when cleaning on stairs.

13. Do not use without dust bag and/or filters in place.

14. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where

they may be present.

15. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

16. Store your cleaner indoors in a cool, dry area.

17. Unplug before connecting the crevice nozzle.

18. To reduce the risk of electric shock, this vacuum cleaner has a polarized plug (one blade is wider

than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlets, reverse the plug. If it still does not fit, contact a qualified electrician to install the

proper outlet. Do not change the plug in any way.

SAVE INSTRUCTIONS

Model C37115-13 Rated voltage 120V~

Rated input 1200W Rated frequency 60Hz

Dust container 0.20CUFT Noise ≤78dB(A)

Suction Power 72 in H2O Approvals: UL /CUL

IMPORTANT SAFETY INSTRUCTIONS

TECHNICAL SPECIFICATION

Attach handle

Caution: Do not catch cord under handle.

hose base cover

base

handle

main housing

protective valve

1. From rear of cleaner, align handle with groove and slide onto cleaner. If necessary,

use thumb and finger pressure to slide handle into position.

2. Attach handle with two ST3.5x10 screws in the assembly packet. Use a slotted

head screwdriver for tightening.

Attach hose, extension tube and crevice nozzle

-3-

extension tube

crevice nozzle

joint

furniture nozzle

hose hook

small nozzle

hose retainer

Warning: assembly the dust bag before use.

Checking dust bag

3. Remove front cover; grasp both sides of bag cover near top. Push thumbs against

center of cover and pull out on sides.

4. Check to be sure the paper bag collar is secure with the hose adapter inside the

paper bag collar.

5. Replace front bag cover.

HOW TO ASSEMBLE

(137005)

(137004)

(137006)

(137007)

front cover

dust bag

air inlet

Store Electrical Cord

6. You will find your cord retainer either at the bottom of the upper cord hook or on

the handle above the upper cord hook. Firmly push the electrical cord down into

either cord retainer. This will place the cord out of the way the next time you

vacuum.

7. Next wind the cord around the two cod hooks on the one side of cleaner. On some

models the upper cord hook turns to release the cord. Turn the hook up to store the

cord.

8. Secure the plug to the cord to prevent unwinding.

cord hook

-4-

Starting the vacuum cleaner

The upright vacuum cleaner design allows use on multiple types of carpeting and on

upholstery or bare floors with attachments. When using the attachment tools, place

the handle in the upright position. Do not place cleaner on furniture or steps as

the brush roll may cause damage.

1. Adjust cleaner height setting knob to lowest position for maximum cleaning.

Adjust to a higher setting to make pushing easier. For easy adjustments, tilt the

cleaner back to move the setting knob.

2. Plug electrical cord into outlet.

3. Step on handle release. Pull handle back to a comfortable position.

4. Push On or off power switch.

handle release

clean under

store or use attachments

use

handle release

ON/OFF

旋钮

LOWHIGH

dust indicator 2

Cleaner Height Setting

Warning: Avoid injury, Keep loose clothing, hair, fingers, and all other parts of body

away from any moving part (such as the revolving brush). Turn off the switch and

unplug the cleaner before changing the cleaner height setting.

The front of the cleaner has an adjustment that raises or lowers the cleaner base to

match the type of carpet. With the cleaner cord unplugged, set the adjustment lowest

setting for maximum cleaning. If the cleaner is difficult to push, move adjustment to

next highest setting until cleaner is comfortable to push. The brush roll must reach the

HOW TO USE

(137003)

Knob

carpet for effective cleaning.

Make each adjustment with cleaner switch off and cord disconnected from outlet.

For ease in moving the adjustment knob, place handle in operating position and tilt

cleaner back to remove weight from front wheels.

Thermal Cut-off

This cleaner has a special thermostat that protects the cleaner in case of motor

overheating. If the cleaner suddenly turns off, follow this procedure:

1. Push on/off switch to “off” position

2. Unplug cleaner.

3. Check for source of overheating problem (i.e. full bag, clogged hose or clogged

filter).

4. If a full plug, clogged hose or clogged filter is found, replace the bag, unclog the

hose or replace the filters.

5. Wait at least 30 minutes before attempting to reuse the cleaner.

6. After 30 minutes cool down period, plug the cleaner in and push the rocker switch

to “on” position. The cleaner should turn on.

7. If cleaner still does not operate, take it to the service center for repair.

Bag change indicator

When the dust bag is full of dust, the indicator on the bag cover moves into the window

as the airflow through the bag decreases.. At this time, you should change the dust bag

to restore maximum performance.

If a clean dust bag does not restore maximum performance, check for obstructions in

the hose or airflow passage.

-5-

bag change indicator

How to use accessories

Note: Do not place cleaner on furniture or steps as the brush roll may cause damage.

Place cleaner on floor with the handle in storage position while using accessories.

1. Remove hose from back of cleaner.

2. Place desired accessory onto end of hose.

Crevice nozzle (137005) cleans corners, baseboards, between cushions.

Furniture brush (137007) use brush side to dust furniture, blinds, books, lamps, shelves.

Small nozzle (137006) clean curtains, draperies, cushions, fabrics.

Dust bag (137003)

Extension tube (137004) to extend clean range.

Brush roller (137002)

The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads

from brush roll so it continues brushing the carpet. To maintain the most efficient

cleaning, the bristles must touch the carpet. To test the bristles length, hold a ruler

against the underneath side of the cleaner. If the bristles no longer touch the ruler,

replace the brush roll.

Brush roller belt (137001)

The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap.

Check the belt regularly to be sure it is in good condition. Replace the belt if it is

stretches, cracks or loses tension. Cut away any hair or threads wound around the brush

roll or the belt pulley because the buildup could cause the belt to rotate unevenly.

How to replace brush roller belt

Note: Turn off the switch and unplug the electrical cord before replacing belt.

-6-

Belt pulley can become hot during normal use. To prevent injury, avoid touching the

motor pulley when checking the belt.

belt

motor pulley

brush roll

1. Lower handle to floor to change belt.

2. Loosen, but do not remove, two screws to release hood. Lift hood to remove.

3. Lift left end of brush roll.

4. Remove and discard belt.

5. Place new belt around motor pulley.

6. Place belt around brush roll pulley.

7. Align right end cap with square in base. Push end cap into place.

8. Pull left side of brush roll to stretch belt. Secure left end cap into base.

9. Rotate brush roll to seat belt.

10. Replace the hood. Make sure hood front is behind furniture guard. Hood should

seat onto self-locating screw tabs.

11. Tighten screws.

MAINTENANCE

(137001)

base cover

crashworthy part

How to check and clear hose blockages

Note: Low suction or poor pick up may be due to a blockage in the vacuum cleaner.

Turn off the switch and unplug the electrical cord before clearing hose.

1. Remove hose and check suction at end of hose-if little or no suction, check

disposal dust bag. Change if needed. If no improvement proceed to step 2.

2. Remove the handle from the vacuum cleaner by removing the two screws and

sliding the handle towards the rear.

3. Loosen another two screws, disconnect the attachment hose from the unit. Check

for any obstructions that may be in the hose. Any obstructions can be removed by

using a blunt instrument to clear the hose. Flexing the hose may help loosen the

clog.

4. Reinstall the hose after cleaning the clog. Make sure the hose is inserted into the

top of the vacuum cleaner before reattaching the handle.

-7-

carrying handle

air inlet

Note: If no improvement in performance on carpet, proceed to following page.

1. Remove the attachment hose from the lower hose retainer and look into the hose

retainer for any obstructions. Proceed to step 2 to check for any other blockages.

2. Remove the hood by loosening the two screws located on the top of the hood and

lifting upward.

3. Step on the handle release and lower the handle all way to the floor.

4. Check for blockages in the brush roll area and remove any obstructions found there.

The base hose can be cleared of any blockage by using a blunt instrument.

5. After the blockage is removed, replace the hood and tighten the two hood screws.

Raise the handle to the upright position and replace the hose into the lower hose

retainer.

tube holder

handle

under furniture

lowest position for cleaning

upright position

operating position

Disposal dust bag and filters

Note: Turn off the switch and unplug the electrical cord before changing dust bag.

Never operate the vacuum cleaner without the dust bag or the filter.

The disposal dust bag plays a very important role in the efficiency of a vacuum cleaner.

The purpose of the paper bag is to trap dirt. As the bag traps dirt, it must also be porous

to allow air to pass on through. If the paper bag becomes clogged, no air can pass

through the cleaner and no cleaning can take place regardless of how powerful the unit.

Change the dust bag and check the filters frequently. Some fine particles can restrict

airflow very quickly and will decrease performance even before the bag appears to be

full.

When vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar fine

substances, the bag and filters may require more frequent maintenance.

How to change dust bags

front cover

dust bag

23air inlet

1. Remove front cover. Grasp both sides of bag cover near top. Push thumbs against

centerofcoverandpulloutonsides.

–8-

2. Grasp bag collar; pull down slightly and out to remove bag.

3. Align bag collar hole and notch with hose adapter. Push collar to rear of

compartment. Check to be sure hose adapter inserts into bag collar.

4. Tuck bag into bottom and along sides.

5. Replace front cover. Make sure disposable bag does not catch under front cover.

Motor filter (137008)

Check the motor filter with each disposable dust bag change. Clean or replace as

needed.

To clean motor filter

1. Remove filter from inside bag compartment.

2. Shake filter to remove excess dust. If necessary, rinse the filter under warm

running water.

3. Reinstall filter when completely dry.

Inspect the micron filter periodically and change as needed. For maximum efficiency,

replace the micron filter periodically.

To clean micron filter (137009)

motor filter

micron filter door

micron filter

1. Open micron filter door, grasp micron filter and pull out.

2. Push new micron filter into cleaner.

3. Close micron filter door.

(137003)

Note: turn off the switch and unplug the electrical cord before servicing.

Problem Cause Solution

Motor will

not start.

1.Electrical plug. 1. Push plug securely into outlet.

2. Try another outlet

3. Check circuit breaker.

Motor

suddenly

stops.

1.Thermal cut off. Refer to page 5.

It can’t clean

the carpet or

floor.

1. Disposable dust

bag and filter;

2. Belt;

3. Belt cap;

4. Brush roll;

5. Hose.

1. Change the bag and cleaner or

replace the filters. Hint: if picking

up fine dust, the bag may not look

full but a fine substance tends to

reduce suction when it blocks the

airflow through the paper bag and

filters.

2. Be sure hose adapter inserts into

paper bag.

3. Replace a cut, loose or out of

shape belt.

4. Snap the belt cap inside the hood

if it comes loose.

5. Clean hair and thread from

bristles and end cap area. Replace

brush roll if bristles are worn.

6. Remove any clogs from the hose

that restrict the restrict the airflow.

Check short hose in the base and

long hose.

No suction at

the end of the

hose.

1. Hose adapter;

2. Disposable dust

bag and filter;

3. Hose.

1. Hose adapter has to seat inside the

dust bag. Hint: put the hose in

place before attaching the handle.

The handle secures the hose.

2. Change the bag and clean or

replace the filters. Hint: If picking

up fine dust, the bag may not look

full, but a fine substance tends to

reduce suction when it blocks the

airflow through the paper bag and

filters.

3. Remove any clogs from the hose

that restrict the airflow. Check

short hose in the base and long

hose.

Noise from

the brush

rolls area.

1. Brush roll;

2. Belt.

1. Remove hood and clean debris or

items from the brush roll area.

2. Replace a cut, loose or out of

shape belt.

Cleaner is

hard to push.

1. Cleaner

height setting;

2. Belt.

1. Turn adjustment knob to a higher

position. Hint: Put handle in

operating position. Tilt the cleaner

back to raise the front wheels off

floor. Then turn the knob.

2. Replace a cut or loose and out of

shape belt.

Cleaner

height knob

will not turn.

1. Cleaner height

setting.

1. Hint: Put handle in operating

position. Tilt the cleaner back to raise

the front wheels off floor. Then turn

the knob.

-9-

PROBLEM SOVING

Inhaltsverzeichnis

Andere Minuteman Staubsauger Handbücher

Minuteman

Minuteman CRV Stücklistenhandbuch

Minuteman

Minuteman 724 Leitfaden

Minuteman

Minuteman X705 Bedienungsanleitung

Minuteman

Minuteman V10 Pro Plus Bedienungsanleitung

Minuteman

Minuteman 290 Series Stücklistenhandbuch

Minuteman

Minuteman MPV-31 Stücklistenhandbuch

Minuteman

Minuteman 829 Asbestos Series Stücklistenhandbuch

Minuteman

Minuteman Parker PV9908KLP Leitfaden

Minuteman

Minuteman Tsunami T16WD Stücklistenhandbuch

Minuteman

Minuteman C82985-06 Stücklistenhandbuch

Minuteman

Minuteman Bio-Haz C82907-00 Stücklistenhandbuch

Minuteman

Minuteman Phenom L1518 Bedienungsanleitung

Minuteman

Minuteman C47185-00 Bedienungsanleitung

Minuteman

Minuteman C29486-02 Leitfaden

Minuteman

Minuteman MC827968 Bedienungsanleitung

Minuteman

Minuteman Parker LV02675B Leitfaden

Minuteman

Minuteman X829 Asbestos Series Stücklistenhandbuch

Minuteman

Minuteman C39085-01 Leitfaden

Minuteman

Minuteman mc827854 Bedienungsanleitung

Minuteman

Minuteman Parker LV02675BM Bedienungsanleitung

Minuteman

Minuteman V14 PRO Bedienungsanleitung

Minuteman

Minuteman C82908-00 Leitfaden

Minuteman

Minuteman C84790-00 Leitfaden

Minuteman

Minuteman C82917-00 Leitfaden

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung