Mitsubishi Electric KD Series Bedienungsanleitung

TM-XH719C

CONTACT IMAGE SENSOR (CIS)

KD series for Web Surface Inspection

TM-XH719C

User’s Manual

Design and specification are subject to change without notice.

April 25th 2020

KD6R367CX, KD6R587CX, KD6R587CXS, KD6R807CX

KD6R367CX-NL, KD6R587CX-NL, KD6R807CX-NL

TM-XH719C

Chapter 1 Notice

1-1 Restriction for use

1-2 Precautions

1-3 CE Marking

1-4 Warranty

1-5 Repair

Chapter 2 Overview

2-1 What’s Contact Image Sensor (CIS)

2-2 Principal technology of CIS

2-3 Definition

2-4 Features of scanning pixel

2-5 Interpolation function

2-6 Specifications

2-7 Handling precautions

Chapter 3 Installation

3-1 Dimensions

3-2 Preparation

3-3 Connections

Chapter 4 How to control CIS

4-1 Startup procedure

4-2 Status LED

4-3 Communication

4-4 Line sync timing

Table of Contents

Chapter 5 Getting started

5-1 Initial settings

5-2 Procedure of function settings

Setting①: Initial setting select 1

Setting②: Initial setting select 2

(Setting②For products with

DeviceFirmwareVersion 2. *. *. *)

Setting③: Output format select

Setting④: Switching Resolution

Setting⑤: Sync signal setting

Setting⑥: LED control

Setting⑦: LED setting

Setting⑧: Dark correction

Setting⑨: White correction

Setting⑩: PGA

Setting⑪: Line adjustment

Setting⑫: γ correction

Setting⑬: Mono mode

Setting⑭: Electronic shutter

Setting⑮: Overlap output

Setting⑯: Output width setting

Setting(Others) : Test pattern

Setting(Others) : Error and temperature indications

Setting(Others) : Prevention for Exposure Saturation

Appendix A：Control register list

Appendix B：Error indicator

Appendix C：How to connect with frame grabber

Appendix D：Spec - Power Supply Unit (Option).

TM-XH719C 3

Chapter 1 : Notice

TM-XH719C

Thank you very much for purchasing Mitsubishi Electric Contact Image

Sensor (CIS). This document contains information that introduces how to

use this product appropriately and safely. Read through this document

carefully before starting to use this product in your equipment or system.

This product is designed for the purpose of being used in general industries. Do not use this product for

specific and particular applications (aerospace application, combustive equipment, transportation

equipment, life-support system, safety device, etc.) where special quality and reliability are required and

failure or malfunction could directly threaten people’s lives, or do harm to the human body. Do not use for

applications other than the purpose of being used in general industries intended by Mitsubishi Electric. If

you plan to use such particular applications, contact our sales department personnel before doing so. If

you have be used it for applications other than the general industries intended by Mitsubishi Electric

without consulting our sales department personnel, Mitsubishi Electric SHALL HAVE NO

RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITEDTO ANY AND ALL RESPONSIBILITY

OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY

OR DEATH TO PERSONS OR LOSS OR DAMAGE TOPROPERTY CAUSED BY the PRODUCT.

Determine the applicability of this product to your equipment or devices through an

appropriate analysis or evaluation by the designer of such equipment or devices, or

personnel related to the specification. Such designers or personnel shall warrant the

performance and safety of your equipment or devices such as dust-proof, water-proof, EMC

and EMI, by themselves.

Design, specification and the contents of this document are subject to change without

notice.

1-1 RESTRICTION FOR USE

TM-XH719C

This indicates the Warning or Caution

described above.

This indicates the prohibited action that must

not be handled.

This indicates the mandatory action that must

be carried out.

Be aware of the following warnings and cautions to use

this product appropriately and safely.

Warning This indicates that improper use of this product may result in

a hazard such as death or catastrophic bodily injury.

Caution This indicates that improper use of this product may result in

a hazard such as a bodily injury or property damage.

■Indications and definitions

1-2 PRECAUTIONS

This indicates a prohibited action such as an

operation in a place where this product may

get wet.

This indicates the prohibition of the

disassembly of this product.

This indicates the possibility of the injury

under the specific situation

TM-XH719C 6

Warning

Do not operate this product in a place where it is explosive, combustible or inflammable.

Operating in a place having propane gas, gasoline or flammable gas may cause a fire and/or an

explosion.

Use power supply having protection against overload.

This product may be able to flow large current due to short circuit fault.

Stop operation when you find any abnormalities or defects.

Otherwise, a fire or an electric shock may occur.

Do not repair, disassemble and/or modify by yourself.

Otherwise, a fire, defect, or an electric shock may occur. If you need to repair this product, you must

contact the agency who sold you this product.

Do not get this product wet. Handle this product with water-proofing.

Otherwise, a defect or an electric shock may occur. This product is designated for indoor use. This

product is designed as a line-scan module embedded in a system.

Do not operate this product outdoors.

This product is designed as a line-scan module embedded in a system. This product is designated for

indoor use.

Do not put anything on this product.

Otherwise, a fire or electrical shock may occur because of the things or materials in this product.

1-2 PRECAUTIONS

TM-XH719C 7

Warning

Do not put this product on an unstable surface, slanting and/or vibrating.

Otherwise, drop and/or fail of this product may cause injury.

Do not look at the internal illumination directly.

This product (not included -NL series) comprises a bright illumination.

Avoid the damage that ESD can cause. Never expose the internal electronics to a potentially

hazardous environment. Do not handle this product with an insulation sheet or on wooden

desk. In addition, do not cover this product with any materials having an electrostatic

discharge. Doing so may cause serious damage.

1-2 PRECAUTIONS

TM-XH719C 8

Caution

Do not store this product in the following places.

●In a vibrating or precarious place ●In a humid, smoky, vaporized or dusty place

●In a slanting place ●In a place exposed by direct sun light

●In a temperature vasying place

●Near anything generating heat (eg. A stove, heater, etc)

●In a corrosive gas atmosphere (CL2, H2S, NH3, SO2, NOXetc.)

Care should always be exercised when handling and operating this product with your

equipment or device.

●Do not drop or damage this product. ●Do not put things on this product.

●No food or drink beside this product.

●Do not put any materials or liquids on this product.

●Avoid any ingression of materials, metals or smoke into this product and its connector.

Use the specified power cable connector and CoaXpress® cable.

Power OFF when you insert or remove cables.

Otherwise, an electric shock or a malfunction may occur.

1-2 PRECAUTIONS

CoaXpress® is a trade mark registered by JIIA (Japan Industrial Imaging Association).

TM-XH719C 9

Caution

Keep this product clean. And do not touch the glass surface of this product.

Otherwise, a defect or a failure may occur. When you need to clean this product, you must clean the

glass surface of this product with a soft cloth and IPA etc.

Put cables in a fixed position appropriately while operating.

Otherwise, a connection failure and damage may occur.

Do not use or operate this product in a slanting or unstable place

Do not use or operate this product in a humid, smoky, vaporized or dusty place.

Do not disassemble the side-bracket for mechanical mounting to your equipment or device.

Otherwise, an ingression of materials and dust, or a defect or a malfunction may occur.

Be cautious of your cloths and arms for not to be caught by the sheet metal attached to the

edge of the glass side. It may cause injury.

1-2 PRECAUTIONS

TM-XH719C 10

Caution ( Disclaimer)

Mitsubishi Electric assumes no responsibility and no liability for any damages resulting from

a fire, earthquake or any other act of God, acts by third parties, misoperation by the user

intentionally or accidentally, or used under extreme operating conditions.

Mitsubishi Electric assumes no responsibility and no liability for any damages resulting from

indirect, additional or consequential damages, including but not limited to loss of expected

income and suspension of business activities.

Mitsubishi Electric assumes no responsibility and no liability for any damages resulting from

an unintended use as stipulated in Manual and Datasheet of this product.

Mitsubishi Electric assumes no responsibility and no liability for any damages resulting from

improper handling, use or repair by any party other than Mitsubishi Electric.

Mitsubishi Electric warrants this product in conformity with the specification specified only

in the Datasheet and the Manual of this product.

Mitsubishi Electric’s total liability shall not exceed the purchase price of this product.

1-2 PRECAUTIONS

Andere Handbücher für KD Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Zubehör Handbücher

Mitsubishi Electric

Mitsubishi Electric MELSENSOR VS70 Series Gebrauchsanweisung

Mitsubishi Electric

Mitsubishi Electric PAC-SH91MK-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PZ-70CSW-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSENSOR VS70 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melsensor FA-CF26-SR Service-Handbuch

Mitsubishi Electric

Mitsubishi Electric PAC-SE41TS-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric EMU-CT100 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Lossnay PZ-70CSW-E Kurzanleitung

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20M-11F310 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric KD Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric KD Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric KD Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-AK53BC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RC-380P1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PZ-70CSB-E Kurzanleitung

Mitsubishi Electric

Mitsubishi Electric k-con KS9-BS1-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric DPLS2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric R410A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric IQSS-R-E Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung